MARVEL MACP215-IS01A 15 Inch Built-In Undercounter Clear Ice Maker Owner’s Manual
- June 3, 2024
- Marvel
Table of Contents
MARVEL MACP215-IS01A 15 Inch Built-In Undercounter Clear Ice Maker
Welcome to the Marvel Experience!
Congratulations on your purchase of the industry’s quietest clear ice machine
with the best ice clarity and purity. Your new investment is protected by a
limited warranty for the first year, and hermetically sealed refrigeration
system parts are covered for an additional 4 years. Here’s your guide to the
operation and maintenance of your Marvel Clear Ice Machine to ensure years of
enjoyment. If you have any questions, please contact Marvel Customer Service
or Tech Support at: Phone: 616-754-5601
Email:
- Customer Service: orderdesk@marvelrefrigeration.com
- Tech Support: techsupport@marvelrefrigeration.com
Got a Marvelous Design?
We would love to see how your Marvel product looks in its new home. Send us
photos at marketing@marvelrefriger-ation.com, and we might feature your Marvel
home design on our website and social media!
Warranty Registration
It is important you send in your warranty registration card immediately after
taking delivery of your appliance or you can register online at
www.marvelrefrigeration.com.
The following information will be required when registering your appliance:
Service Number
Serial Number
Date of Purchase
Dealer’s name and address Online registration is available at www
.marvelrefriger-ation.com The service
number and serial number can be found on the serial plate which is located
inside the cabinet on the left side near the top.
Tip
Click on any section below to jump directly there
Installation
- Integrated Panel Dimensions
- Integrated Panel Installation
INTEGRATED PANEL DIMENSIONS
NOTE
- Panel thickness maybe 5/8″ or 3/4″
- Center the unit in the 24″ opening
- If the hinge side of the product is pressed against the adjacent cabinet, use a 5/8″ thick panel
- The window cutout is for glass door models only Do not use a solid door panel on a glass door model
Cut and prepare panels according to the information provided in the Integrated Panel Dimensions section.
CAUTION
It is important to use the factory-provided grille that came with the product
to assure proper airflow is maintained through the condenser. The use of a
custom grille is not recommended and will void the warranty.
Step 1 Removing the Door and Hinges
Hold the door secure in the closed position and remove the Hinge Pin from the
Upper Hinge using a 1/8” Hex Key tool. Slowly remove the door by sliding it
outward away from the cabinet and lift to remove the Lower Hinge. If reversing
the door, remove the hinges from the cabinet per Door Reversal Instructions.
Remove the hinge bushing from the adaptor plate. A new bushing is included in the literature pack with your unit.
Step 2: Remove the Door Gasket
With the door laying on a flat surface and starting at a corner of the door,
remove the magnetic door gasket from the interior side of the door. Set the
gasket aside on a flat surface. There are 10 holes in the gasket retainer
extrusions (3 on each side and 2 at the top and bottom) which are used to
fasten the panel to the front of the door. The screws are provided in the
literature pack.
Step 3: Assemble the Panel to the Door
The preferred method of attaching the panel to the door is to clamp the panel
to the door so it cannot move while drilling the screw pilot holes. Use bar
clamps or “C” clamps with pads on the clamping surfaces that will not mar the
panel or the door. The custom panel should be flush with the top of the door
and centered along the width of the door. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill size from the chart
in the table below being careful not to drill through the front surface of the
panel. Fasten the panel to the door with the 10 screws provided in the
literature pack. Remove the clamps and replace the gasket in the gasket
extrusion channels of the door. Some force may be required to seat the gasket
into the channels. Be sure the gasket corners are seated properly.
Step 4: Install the Door
If reversing the door swing, reinstall the hinges per Door Reversal
Instructions. Carefully slide the lower hinge bushing over the bottom hinge
pin. Install the new upper hinge bushing into the adaptor plate.
Align the hinge bushing with the top hinge and reinstall the upper hinge pin using a 1/8” Hex Key so that the pin is flush.
References
- The domain name ATION.COM is for sale | Dan.com
- Premium Undercounter Products for Home & Outdoor | Marvel Refrigeration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>