GEPRC RAD VTX 5.8G 4-7 Inch FPV Freestyle Drone Instruction Manual

GEPRC RAD VTX 5.8G 4-7 Inch FPV Freestyle Drone Instruction Manual

Mark4-7 Inch Instruction Manual

Arm installation

Install the arms, screws and MR30 plug

Unlock switch

After successful linking, connect to the Betaflight ground station. Enter the mode option and try to toggle each function switch on the remote control. When the yellow cursor
moves to the set range, the corresponding function will be turned on.

TBS Nano RX Receiver

1While powering on the receiver, press and hold its Bind button until the green light rapidly flashes, then release the Bind button. Press and hold the receiver’s Bind button again for 8 seconds, then release it. Wait for the green indicator light on the receiver to turn off and the red light to flash slowly. You will see !Update micro RX?’ on the remote control screen-select ‘ENTER!
2.Wait for the update to complete and the automatic binding process. Once successfully bound, the remote control will display Binding Ok’ and the TBS Nano RX receiver indicatol.

ELRS Receiver

We recommend checking whether the tuner and receiver firmware are consistent before binding. If they are inconsistent, please upgrade the firmware. 1.To activate bindina mode, power cvcle the receiver three times, When successful,the receiver’s LED will rapidly flash twice, indicating it’s in binding mode.
lf you are using the RadioMaster TX12 transmitter, access the TOOLS interface by long pressing the SYS Then, navigate to ‘ExpressLRS’ and enter this option, Inside the ‘ExpressLRS’ menu, locate the ‘Bind’ button on the ExpressLRS Lua script and select it, This action will send out a binding pulse, and a popup will briefly appear and then disappear.
If the receiver’s LED indicator turns into a solid light, it’s a clear indication that the binding process has been successfully completed

RAD VTX 5.8G 1.6w /5.8G 2.5W setting

VTX frequency：

Manual setting:
Press and hold for 3 seconds, the blue light will flash 3 times, indicating entering the frequency selection menu.
Press and hold for 3 seconds and the green light will flash 3 times, indicating entering the frequency band selection menu.
Press and hold for 3 seconds and the red light will flash 3 times, indicating entering the power selection menu.

Propeller steering and installation

 Frequency

LED Color

|

CH1

|

CH2

|

CH3

|

CH4

|

CH5

|

CH6

|

CH7

|

CH8

---|---|---|---|---|---|---|---|---

Blue

|

Flash 1X

|

Flash 2X

|

Flash 3X

|

Flash 4X

|

Flash 5X

|

Flash 6X

|

Flash 7X

|

Flash 8X

Frequency band

LED Color

|

Band A

|

Band B

|

Band E

|

Band F

|

Band R

---|---|---|---|---|---

Green

|

Flash 1X

|

Flash 2X

|

Flash 3X

|

Flash 4X

|

Flash 5X

Power (1.6W power is 25mW-1600mW)

LED Color

|

Pit

|

25mW

|

200mW

|

600mW

|

1600mW

|

2500mW

---|---|---|---|---|---|---

Red

|

Lignt ON

|

Flash 1X

|

Flash 2X

|

Flash 3X

|

Flash 4X

|

Flash 5X

Propeller steering and installation

Pre-Flight

1. Please install the antenna before powering
2. Verify that the propellers are oriented correctly and ensure the propeller nuts are securely
3. Ensure the battery is securely strapped to the Check that the battery’s balance connector is neatly arranged and secured to prevent it.
4. Please check the battery When fully charged, the 4S voltage is 16.8v and the 6S voltage is 25.2v.
5. Turn on the remote control, select the correct model, make sure the unlock switch is in the locked state and the throttle position is at the lowest; Activate your FPV goggles or screen and scan for any frequency interference.
6. Keep a safe distance of 3 meters to test the unlocking and see if the propeller rotate after the quadcopter is powered

Please flight in a safe area where no one is approaching.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>