Arktic 271575 Ice Cube Machine User Manual

: June 7, 2024
: Arktic

Arktic

Arktic 271575 Ice Cube Machine

product

You should read this user manual carefully before using the appliance.

Dear Customer,
Thank you for purchasing this Arktic appliance. Before using the appliance for the first time, please read this manual carefully, paying particular attention to the safety regulations outlined below.

Safety regulations

This appliance is intended to be used in household and similar applications such as

Staff kitchen areas in shops, offices and other working environments;
Farm houses and by clients in hotels, motels and other residential type environment;
Bed and breakfast type environments;
Catering and similar non-retail applications.

This appliance should be operated by trained personnel in kitchen of the restaurant, canteens or bar staff, etc.
The appliance must only be used for the purpose for which it was intended and designed. The manufacturer is not liable for any damage caused by incorrect operation and improper use.
Keep the appliance and electrical plug away from water and any other liquids. In the event that the appliance should fall into water, immediately remove plug from the socket and do not use until the appliance has been checked by a certified technician. Failure to follow these instructions could cause a risk to lives.
Never attempt to open the casing of the appliance yourself.
Do not insert any objects in the casing of the appliance.
Do not touch the plug with wet or damp hands.
Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunctions, repairs are to be conducted by qualified personnel only.
Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact the retailer if it is damaged.
Warning! Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
Regularly check the power plug and cord for any damage. If the power plug or power cord is damaged, it must be replaced by a service agent or similarly qualified persons in order to avoid danger or injury.
Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. To pull the plug out of the socket, always pull on the plug and not on the cord.
Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
Always keep an eye on the appliance when in use.
Warning! As long as the plug is in the socket the appliance is connected to the power source.
Turn off the appliance before pulling the plug out of the socket.
Never carry the appliance by the cord.
Do not use any extra devices that are not supplied along with the appliance.
Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
Connect the power plug to an easily accessible electrical outlet so that in case of emergency the appliance can be unplugged immediately. To completely switch off the appliance pull the power plug out of the electrical outlet.
Always turn the appliance off before disconnecting the plug.
Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
This appliance must not be used by children under any circumstances.
Keep the appliance and its cord out of reach of children.
Always disconnect the appliance from the mains if it is left unattended or is not in use, and before assembly, disassembly or cleaning.
Never leave the appliance unattended during use.

Special safety regulations

This appliance is intended only for making ice cube. Any other use may lead to damage of the appliance or personal injury.
Use the appliance only as described in this manual.
Caution! Hot surface! The surface is hot when in use. Touch the control panel only.
Caution! Risk of fire! The refrigerant used is R290 in this appliance. It is a highly flammable refrigerant. The insulation foaming agent used is C5H10 in this appliance. They are highly flammable.
Do not place the appliance on a heating object (gasoline, electric, charcoal cooker, etc.) Keep the appliance away from any hot surfaces and open flames. Always operate the appliance on a level, stable, clean, heat-resistant and dry surface.
This appliance is not intended to be operated by means of an external timer or separate remote-control system.
WARNING: Keep all ventilation openings in the appliance enclosure clear of obstruction.
WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
WARNING: Do not damage the refrigerant circuit.
WARNING: Connect to potable water supply only.
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Allow at least 10 cm spacing around the appliance for ventilation purpose during use.
Do not use hard utensils to hit the outer surface. Do not use water jet, flush directly with water or steam cleaner as the parts will get wet and electric shock might be resulted.
Do not expose it to direct sunlight. Avoid mechanical shocks and vibrations.
Always move or transport the appliance in an upright position or it may damage the appliance.
Caution! Securely route the power cord if necessary in order to prevent unintentional pulling or contact with the heating surface.
Do not clean or store the appliance unless it is completely cooled down.
No any parts are dishwasher safe.

IMPORTANT: The wires in this mains lead are colored in accordance with the following code:

Green and yellow: Earth
Blue: Neutral
Brown: Live

As the color of the wires in the mains lead of the appliance may not correspond with the colored markings identifying the terminal in your plug, proceed as follows:
The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with the letter E, G or by symbol or colored green or green-and-yellow. The wire which is colored blue must be connected to the terminal which is marked with the letter N.
The wire which is colored brown must be connected to the terminal which is marked with letter L.
NOTE: Created ice cubes are joined together and still need to be broken apart before use.

Intended use

This appliance is intended for household use and other similar applications.
The appliance is designed only for making ice cubes. Any other use may lead to damage to the appliance or personal injury.
Operating the appliance for any other purpose shall be deemed as misuse of the device. The user shall be solely liable for the improper use of the device.

Grounding installation
This appliance is classified as protection class I appliance and must be connected to a protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Technical Specifications

Dimensions/ Connections
Rating
Item no.| 271575
---|---
Operating voltage and frequency| 220-240V~ /50Hz
Rated current| 2,2A
Rated input power| 280W
Refrigerant used & injection quantity| R290 / 95g
Climate class| SN, N, ST, T
Flammable forming agent| C5H10
Protection class| Class I
Running conditions| Room temp 10°C ~ 38°C

Water supply temp 5°C ~ 35°C Water supply pressure 0,04 ~ 0,6 MPa

Net weight (approx.)| 27kg
Dimension| 448x400x(H)798mm

Remark: Technical specification is subjected to change without prior notification.

General information

Main Unit Construction

Overview

Top cover
Door
Ice-making & water tank assembly
Front panel
Operation panel
Air outlet: Must keep the air circulate smoothly, hot air will blow out when unit running.
Water draining port.
Water inlet port for water supply.

Accessory: White 2 meters long water drain pipe, connector for the water faucet, white 3 meter long water supply pipe(ø 6.35mm). Overview
2

A. Water dividing pipe: with nine little holes, wa-ter will flow out from these little holes.
B. Evaporator (ice-making module)
C. Ice full detecting board.
D. Water tank.
E. Water supplying pipe.
F. Cover board on the right side of the evaporator.
G. Water level switch installing plate.
H. Water drain pipe of the water tank.
I. Water pump.
J. Water level detecting switch.

Operation panel

Overview 3

A. ” Add water” light: When the light flashes, it means the water is supplied to slow; and when the light is on always, it means absence of water in unit.
B. ”Timer” light: When this light is on, it means the TIMER is set. Timer can be set on or off with the clean/timer button.
C. ”Ice” light: If the light is on, means the unit is making ice; And if the light flashes, means the unit is during the ice-harvest process.
D. “Full” light: When the unit is full of the ice cube, the light will be on.
E. “Clean” light: When this light is on, water pump cleaning start. When the light flashes, water pump cleaning stop.
F. “▲” &“▼” button: Use to adjust the ice-making process duration period length, the default setting is zero, 1 minute adding or decreasing per each pressing of “▲” or “▼” button. Also to adjust the delay time of the timer, the de-fault setting is zero, 1 hour adding or decreasing per each pressing of “▲” or “▼” button.
G. LED Display: At normal condition, the number in the window is always on, it displays the ambient temperature; And if the number flashes, it will display the time left in minutes of each process, like ice-making cycle, self-cleaning program, etc.
H. “ ” (“On/Off”) button: When the unit is off, press this button to turn on the unit; And during the Self-cleaning program, or normal ice-making state, press this button to turn off the unit at once; And also if the unit is set with the Timer, press this button to cancel the Timer setting. When the unit is making the ice cube, press this button for more than 5 seconds, the unit will switch to ice harvest process by force.
I. “ ” (“Timer clean”) button: Quickly press this button once, to enter the Timer setting pro-gram; And press this button for more than 5 seconds when the machine is off, to enter the Cleaning program.

No.| Parts Name| Qty.| Notes| No.| Parts Name| Qty.| Notes
---|---|---|---|---|---|---|---
1| Front panel| 1| | 23| Evaporator and its frame| 1|
2| Bottom plate| 1| | 24| Water supplying pipe| 1|
3| Condenser| 1| | 25| Water dividing pipe, with nine holes| 1|
4| Operation panel paper| 1| | 26| Cap of the water dividing pipe| 1|
5| Operation panel PCB box| 1| | 27| Electrical PCB box| 1|
6| Operation panel PCB| 1| | 28| Main control PCB| 1|
7| Compressor| 1| | 29| Cover of the main control PCB| 1|
8| Adjustable foot| 4| | 30| Rear plate| 1|
9| Dry filter| 1| | 31| Insulation sponge of the top cover| 1|
10| Capillary| 1| | 32| Top cover| 1|
11| DC fan| 3| | 33| Ice shovel| 1|
12| Water inlet valve| 1| | 34| Left side plate| 1|
13| Water drainage pipe of the water tank| 1| | 35| Foaming inner cabinet & Ice storing bin| 1|
14| Ice-harvesting Electro-magnetic valve| 1| | 36| Door frame| 1|
15| Water tank| 1| | 37| Back strength plate| 1|
16| Right side plate| 1| | 38| Water outlet pipe of the inner cabinet| 1|
17| Water circulation pump| 1| | 39| Water drainage cap| 1|
18| Cover of the water tank| 1| | 40| Water drainage port| 1|
19| Water level detecting switch| 1| | 41| Door| 2|
20| Ice-full detecting plate| 1| | 42| Water inlet port| 1|
21| Magnetic control switch| 4| | 43| Power cord| 1|
22| Cover board on the right side of the evaporator| 1| | 44| Clipper of the power cord| 1|
45| Wiring| 1|

Unpacking your ice maker

Remove the exterior and interior packaging. Check if all the accessories, including instruction manual, ice scoop, white water inlet pipe, 4 ways to 2 ways water quick connector and the water draining pipe, etc., are inside or not. If any parts are missing, please contact our customer service.
Remove the tapes for fixing the door and inned cabinet, ice scoop, etc.. Roughly clean the inner cabinet & ice scoop with wet clothe.
Put the ice maker on a level & flat floor, without direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Maker sure that there is at least 20cm gap between the air outlet and the obstacles, and at least 5 cm between Left/Right side and the wall.
Allow 4 hours for the refrigerant fluid to settle before plugging the ice maker in if the unit may-be fall upside down during shipping or transportation.
The appliance must be positioned so that the plug is accessible.

WARNING: Only use drinking water to make ice.

Installation location requirement

Keep the proper room temperature and inlet water temperature according to above specification table. Otherwise it will affect the ice making per-formance.
This unit should not be located near any heat source.
The unit should be located on a firm & level foundation at normal counter top height.
There must be at least 15 cm clearance at rear side for connection and 20 cm clearance in front to open the door and keep good air circulation.
Do not put anything on the top of the ice maker.

When installing the ice maker under a counter, fol-low the recommended spacing dimensions shown above. Place electrical and water supplies and drain fixtures in the recommended locations as shown.
Choose a well-ventilated area with temperatures above 10˚C and below 32˚C. This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray or drips.
The ice maker requires a continuous water supply with pressure 1-8 Bar as required in above specification table. The temperature of the water feeding into the ice maker should be between 5˚C and 25˚C for proper operation.

Electrical requirement & connections

WARNING: THIS UNIT MUST BE EARTHED.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection.
It is recommended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain. If the supply cord or plug to be replaced, it should be done by a qualified service engineer.
This appliance requires a standard 220-240 Volt, 50Hz electrical outlet with good grounding means.

Cleaning your ice maker before first using

Open the door.
Clean with diluted detergent, warm water and a soft cloth.
Repeatedly clean the water contacting inner parts, you can pull the Water drain pipe of the water tank indicating “H” in above illustration to drain the cleaned water in the water tank, next clean the inner ice-storing cabinet. After that drain out all of the cleaning water from the water drain port located at the back of the unit (“7”in above illustration). Reinstall the water drain pipe and the cap of the water drain port, otherwise, the unit will not work properly. Discard the first ice-cube after cleaning.
The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
Dry the interior and exterior with a clean soft cloth.

Water connection for your ice maker

Important: Be sure to use the new hose-sets sup-plied with the appliance.
Connect the water supplying hose to the unit

Step 1: First remove the clipper on the water inlet port (indicated in the following illustration “B”) located at the back of the unit. Remove the anti-dust plug.

Step 2: Insert the one end of the white water hose into the water inlet port, and push inward completely, and install back the clipper, then water hose connection is completed.

Connecting the water drain pipe
Pull out the water drainage cap with black color (indicated “A” in above illustration), then connect the white drainage pipe included in accessory, connect the other end of this drainage to the main water drainage pipeline.

Connect the water hose to the water faucet of the water main supply system

The supplied water quick-connector must be screwed to a faucet; remove the clipper from the water quick-connector, insert the other end of the water hose into this quick-connector port completely, install back the clipper.

Important: The water pressure of main water sup-ply system must be 0.04-05 MPa at.

Operation the ice-making process

After all of the water pipe connecting is completed, plug in the main power supply. Then press “ ” button on the control panel to begin the ice making cycle, and the “Ice” light will be on at same time. The digit window will display the ambient temperature normally. The compressor, fan motor and water pump will run during ice making process.
Each ice making cycle will last about 11 to 30 minutes, depending on the ambient temperature and the water temperature.
When the ice-making process is over the ma-chine will switch to ice-harvest process. At same time the system will detect the water lev-el, if the water level is lower than required, “Add water” light starts flashing, open the water inlet valve to supply extra water to water tank, when the water supplying process is finished, the “Add water” light is off again.
When the “Full ” indicator is on, the unit stops running. If you remove enough cubes, the unit will start to work again after a 3 minute period.
During the ice-making process, press the “▲” or “▼” button to adjust the ice-making process duration period length, this will change the thickness of the ice cube. The default setting is zero, 1 minute will add or decrease to the process per pressing of the “▲” or “▼” button. 5 seconds after the last press, the new setting are programmed.
Bad water quality will cause bad quality of ice cubes and will reduce the transparency of the ice cube.

NOTE: Created ice cubes are joined together and still need to be broken apart.

Automatic self-cleaning program
Start the self-cleaning program: After connecting all of the water pipe, plug on the main power supply plug press the “ ” button for more than 5 seconds, this starts the cleaning program. The “Clean” light will be on during cleaning, the digit window will indicate the left time. The self-cleaning program takes 30 minutes.

Cancel the self-cleaning program: It takes about 30 minutes to complete one self-cleaning program. When the program is over, the system will be in off- state automatically. And also you can press the “POWER” button on control panel to cancel the self-cleaning program by force.

Timer Setting

How to set the timer: When the machine is off, press the “Timer/Clean” button to set the time when the machine has to turn on. The “Timer” light will go on, the number in digital window will flash to display in how many hours the machine will go on. During the number flashing, press “▲” , “▼” button to add or remove hours, the default setting is zero. Five seconds after setting, your desired setting will be programmed.

How to cancel the ON-Timer: Press the “Timer/Timer” button, the number in digital window will flash to display the present delay time of your ON-Timer, and press the button again to cancel the setting. Pressing the “POWER” button will also cancel the timer.
How to cancel the OFF-Timer: This is the same procedure as for canceling the ON-Timer.

Wiring diagram

Normal Sounds

Your new ice maker may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls and cabinets can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them.

You will hear a swooshing sound when the water valve opens to fill the water tank for each cycle.
Rattling noises may come from the flow of the refrigerant or the water line.
The high-efficiency compressor may make a pulsating or high-pitched sound.
Water running from the water tank to the evaporator plate may make a splashing sound.
Water running from the evaporator to the water tank may make a splashing sound.
As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice-maker.
You may hear air being forced over the condenser by the condenser fan. During the harvest cycle, you may hear the sound of ice cubes falling into the ice storage bin.
When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

Preparing the ice maker for long storage

If the ice maker will not be used for a long time, or is to be moved to another place, it will be necessary to drain out all of the water in the system.

Turn off the unit, and unplug the power cord.
Shut off the water supply at the main water sup-ply.
Disconnect the water supply hose from the water inlet valve.
Pull out the Water drain pipe of the water tank (H in illustration) to drain out the water in the water tank. When all the water has been drained, reinstall the water drain.
Drain out all the water from the water drain port located at back of the unit (7 in illustration).
Disconnect the water drain pipe to the main drain pipeline or floor drain, plug on the drain cap again.
Leave the door open to allow for circulation and prevent mold and mildew.
Leave water supply hose and power cord disconnected until ready to reuse.
Dry the interior & wipe the outside of the unit.
Put a plastic bag on the unit to resist out dust & dirty.

Cleaning & maintenance

WARNING: Do not use any alcohol or fume for cleaning/sanitization of the ice maker. It may cause cracks on the plastic parts. Ask a trained service person to check and clean the condenser at least once a year, in order to let the unit work properly. This appliance must be cleaned by use of a water jet.
CAUTION: If the ice maker has been left unused for a long time, before the next use it must be thoroughly cleaned. Follow carefully any instructions provided for cleaning or use of sanitizing solution. Do not leave any solution inside the ice maker after cleaning.

Periodic cleaning and proper maintenance will en-sure efficiency, top performance, hygienic, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, or the unit is used out-doors, or there are other special considerations.
What shouldn’t be done
Never keep anything in the ice storage bin that is not ice: objects like wine and beer bottles are not only unsanitary, but also it’s labels may slip off and obstruct the drain pipe.

Exterior Cleaning

The door and cabinet may be cleaned with a mild detergent and warm water. Do not use sol-vent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe dry with a soft clean towel to prevent water spotting.

NOTICE: Stainless steel models exposed to chlorine gas and moisture, such as in areas with spas or swimming pools, may have some discoloration of stainless steel. Discoloration from chlorine gas is normal.

Interior Cleaning

For Ice Storage Bin
The ice storage bin should be sanitized occasion-ally. Clean the bin before the ice maker is used for the first time and reused after stopping for an extended period of time. It is usually convenient to sanitize the bin after the outside, the storage bin must be empty.

Disconnect power to the unit.
Open the door and with a clean cloth, wipe down the interior with a sanitizing solution made of 28g of household bleach or chlorine and 7.5L of hot water.
Rinse thoroughly with clear water. The waste water will be drained out through the drain pipe.
Reconnect power to the unit.
The ice scoop should be washed regularly. Wash it just like any other food container.

WARNING: Do not use solvent-based or abrasive cleaners. These may transmit taste to the ice cubes.

Ice Making Parts Cleaning

During the using, periodically to clean these main system of your ice-maker.

Repeat above step to clean the water tank and other inner parts of the unit.
Clean the water dividing pipe on the evaporator extra, uninstall this part and clean each little hole displayed in the following illustration, make sure each hole is not clogged, then install back to the original location.
When there are ice cubes on the surface of the evaporator, but they can’t fall, don’t remove it by force; just press the “POWER” button for more than 5 seconds, the unit will enter the ice melting process. After some while the big ice-cubes will fall down. Turn off the unit and unplug the power cord to clean the surface of the evaporator.
For the water tank and ice-full detecting plate.

Also the water tank and the ice-full detecting plate is very important to keep your ice cube hygienic. Put mixture of neutral cleaner & water into a clean water jet, then spray to all the inner surface of tank & the ice detecting plate. Wipe these surfaces as far as possible with a clean cloth. And then, spray the surfaces with clean water, wiping with a dry clean cloth. Then drain out the cleaned water in the water tank by pulling out the Water drain pipe of the water tank indicating (H in illustration). When all of the cleaned water has been drained out, re-install back the water drain pipe of the water tank.
Suggestion: After cleaning the interior parts dis-card the first batch of ice.

Descaling the machine

Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 4 to 5 grains/liter, you may need to clean the system as often as every 6 months.

Turn off the ice maker. Keep the ice maker connect to the water supply and drainpipe. But shut off the water faucet of main water supply.
Open the door and scoop out all of the ice cubes. Either discard them or save them in an ice chest or cooler.
Making the cleaning solution. Please mix the Nu-Calgon Nickle Safe Ice Machine Cleaner with water to make the cleaning solution.
WARNING: Wear rubber gloves and safety goggles when handling Ice Machine Cleaner
Use a plastic or stainless container with more than 4 liters capacity, mix 300 ml Nu-Calgon Nickle Safe Ice-machine Cleaner with 2.8 liters warm water about 50-60ºC, Then divide them for 2 shares equally in 2 cups. It is better to keep the temperature of each cup of the cleaning solution.
Check to be sure that the water drain pipe of the water tank has been installed properly in the slot of the tank wall. Then Pour one cup of Nickel-Safe Ice Maker Cleaning Solution into the water tank. Wait about for 5 minutes.
Turn on the power to the ice maker, then press “ ” button on control panel for more than 5 seconds, to enter the self-Cleaning program. During this process, the “Clean” light will always be on during this period, and the digit window will indicate the time left.
After self-cleaning program, pull out the drain pipe of the water tank, drain the cleaning solution down to the lower ice storage bin. Shake the unit slightly to drain out all of the cleaning solution completely. Then install back the drain pipe to the slot of the water tank.
Repeat steps 4–6 to clean the ice making assembly system again.
WARNING: The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-based cleaner products. Use rubber gloves to protect hands. Carefully read the material safety instructions on the container of the ice machine cleaner.
Open the water faucet of the main water supply, let the water flow in the unit. Again press the“ ” button on control panel for more than 5 seconds, to enter the self-Cleaning program. Through this process, It will rinse the water dividing pipe, evaporator, water pump, silicone pipe, and water tank, etc..
After one self-cleaning program complete, then pull out the drain pipe of the water tank, drain the cleaning solution down to the lower ice stor-age bin, also shake the unit slightly to drain out all of the water completely. Then install back the drain pipe to the water tank slot tightly.
Repeat the step 8-9 again 2 times.
Following the above program to clean the ice storage bin .
Discard the first batch of ice cube.

Cleaning Suggestion

DAILY CLEANING
The ice shovel, door and the water dividing pipe should be cleaned by yourself per each day. At the end of every day, rinse the ice shovel and wipe the both sides of the door with a clean cloth.
SEMI-MONTHLY CLEANING
The ice shovel, ice bin, water tank, the ice-full detecting plate and the surface of the evaporator are to be cleaned by yourself semi-monthly ac- cording to interior cleaning program.
SEMI-ANNUAL CLEANING
All the components & surfaces exposed to wa-ter or ice cubes, like ice storage bin, water tank, door, evaporator, water pump, silicone tube, wa-ter dividing pipe, etc. should be cleaned by Using Nu-Calgon Nickle Safe Ice-machine Cleaner per each 6 months.

Trouble shooting

Problem	Possible	Solution
“Add water” indicator is on.	No water supply	Check the main water supply

pressure or check the water supply hose is blocked or not, adding the water pressure or cleaning the hose necessary.
Floating ball of the water level detecting switch is blocked, can’t be raised up| Clean the water tank and the water level detecting switch.
Water flows out from the water tank| Place the unit on the level position, not on the slope.
Water flows out from the water drain pipe of the water tank.| Pull out the pipe and install back to the slot of the water tank properly.
“Add water” indicator flashes| Water supplying hose breakdown, or water flows in very slowly.| Check the main water supply pressure or check the water supply hose is blocked or not, adding the water pressure or cleaning the hose necessary.
Water pump is working, but no water flow out from the water dividing pipe| The little holes on the water dividing pipe is blocked.| Clean these little holes.
The transparency of the ice cube is not very good| Water quality is bad| Change the water supply, or use the water filter to soften or filter the water.
Ice cube shape is irregular| Water quality is not good or the water tank is very dirty| Clean the water tank, and change with new water.
The little holes on the water dividing pipe is some blocked| Clean the water dividing pipe, make sure all nine holes are unclogged.
Ice cube is very thin| Ambient temperature is too high| Move the unit to low temperature space, or lengthen the time of each ice making cycle.
Air circulation around the unit is not good| Make sure there is more than 20CM space between the unit back & front and the obstacle
Ice cube is too thick| Ambient temperature is too low| Reduce the time of each ice making cycle.
“Full” indicator is on| The ice storage bin is full of the ice cube.| Take out some ice cube
Ice making cycle is normal, but there is no ice cube produced| The temperature of Ambient, or water in water tank is too high| Move to the place with temperature lower than 32 centigrade, and change to the low temperature water
Refrigerant leakage| Need the technical serviceman to maintain
Cooling system tube is clogged| Need the technical service person to maintain

Error indicator

E1: Ambient temp sensor breakdown
E2: The duration time of one ice making cycle is more than 35 minutes, the unit will be turned off. It is the system protection of no refrigerant in cooling system or the compressor not work.

Warranty

Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or re-placement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in any way. Your statutory rights are not affected. If the appliance is claimed under warranty, state where and when it was purchased and include proof of pur-chase (e.g. receipt).
In line with our policy of continuous product development we reserve the right to change the product, packaging and documentation specifications with-out notice.

Discarding & Environment
When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose to your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment and ecological disposal, either directly or through a public system. Arktic