Arktic 233269 4 Shelves Refrigerated Display Cabinet User Manual
- June 6, 2024
- Arktic
Table of Contents
- Safety regulations
- Special Safety Regulations
- Different operation parts
- Operation
- Cleaning and Maintenance
- Troubleshooting
- Technical specification
- Circuit diagram (Item 233238, 233269, 233610, 233627, 233634, 233641,
- Circuit diagram (Item 233290, 233696)
- Warranty
- Discarding & Environment
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
User manual
REFRIGERATED DISPLAY CABINETS
Item: 233238
233269
233290
233610
233627
233634
233641
233658
233665
233696
You should read this user manual carefully before using the appliance.
Keep these instructions with the appliance.
For indoor use only.
Dear Customer,
Thank you for purchasing this Arktic appliance. Before using the appliance for
the first time, please read this manual carefully, paying particular attention
to the safety regulations outlined below.
Safety regulations
- This appliance is intended for commercial use only.
- The appliance must only be used for the purpose for which it was intended and designed. The manufacturer is not liable for any damage caused by incorrect operation and improper use.
- Keep the appliance and electrical plug away from water and any other liquids. In the event that the appliance should fall into water, immediately remove plug from the socket and do not use it until the appliance has been checked by a certified technician. Failure to follow these instructions could cause a risk to lives.
- Never attempt to open the casing of the appliance yourself.
- Do not insert any objects in the casing of the appliance.
- Do not touch the plug with wet or damp hands.
- Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunctions, repairs are to be conducted by qualified personnel only.
- Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact the retailer if it is damaged.
- Warning! Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
- Regularly check the power plug and cord for any damage. If the power plug or power cord is damaged, it must be replaced by a service agent or similarly qualified persons in order to avoid danger or injury.
- Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. To pull the plug out of the socket, always pull on the plug and not on the cord.
- Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
- Always keep an eye on the appliance when in use.
- Warning! As long as the plug is in the socket the appliance is connected to the power source.
- Turn off the appliance before pulling the plug out of the socket.
- Never carry the appliance by the cord.
- Do not use any extra devices that are not supplied along with the appliance.
- Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
- Connect the power plug to an easily accessible electrical outlet so that in case of emergency the appliance can be unplugged immediately. To completely switch off the appliance pull the power plug out of the electrical outlet.
- Always turn the appliance off before disconnecting the plug.
- Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
- This appliance must not be used by children under any circumstances.
- Keep the appliance and its cord out of reach of children.
- Always disconnect the appliance from the mains if it is left unattended or is not in use, and before assembly, disassembly or cleaning.
- Never leave the appliance unattended during use.
Special Safety Regulations
-
This appliance is designed for short-time storage of packaged food such as lettuce, vegetables, drinks, fruits, etc. under low temperature. Do not store any other materials in the appliance. Do not place any dangerous products, such as fuel, alcohol, paint, flammable or explosives, etc. inside or near the appliance. Do not store medicine inside the appliance.
-
Products put in the appliance must be already pre-cooled. Otherwise, moisture evaporating while cooling food products can condensate inside the cooling compartment, this is natural and does not indicate any malfunction of the appliance.
-
This appliance must be installed, commissioned, and serviced by a qualified or trained person. And this appliance is intended to be used by trained or qualified personnel such as kitchen or bar staff.
-
WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
-
WARNING: Do not damage the refrigerant circuit.
-
Caution! Risk of fire! The refrigerant used is R600a / R290 It is a flammable refrigerant that is environmentally friendly. Although it is flammable, it
does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the
noise level of the appliance. In addition to the noise of the compressor, you might be able to hear the coolant flowing around the system. This is unavoidable and does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes. -
WARNING: Keep all ventilation openings in the appliance enclosure clear of obstruction. Provide sufficient ventilation in the surrounding structure when building in. Never block the airflow suction and air outlet in order to keep air circulation.
-
WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
-
Place the appliance on a clean, stable, dry, level surface only.
-
Keep the appliance away from any hot surfaces and open flames. Protect the appliance against heat, dust, direct sunlight, moisture, dripping, and splashing water.
-
During use, keep 10cm around the appliance free for ventilation.
-
Do not use hard utensils on the glass surface. Do not use water jets or steam cleaners during cleaning, do not immerse the whole appliance in water as the parts will get wet and electric shock might be resulted.
-
Do not place articles on top of the appliance. Do not place objects with open sources of fire (e.g. candles) on top or beside the appliance. Do not place objects filled with water (e.g. vases) on or near the appliance.
-
Never cover the appliance during use. This may cause a fire hazard.
-
Do not wash the appliance with water. Washing can cause leakages and increase the risk of electric shock.
-
Do not make any additional openings on the appliance. Do not install any gadgets in the appliance.
-
Do not overload the racks inside to avoid damage. Max. loading of each rack is about 8kg.
-
Do not attempt to climb up to the top of the appliance.
Installing the appliance
- The appliance should not be tipped over an angle of 45°. After installing the appliance, wait for 2 hours before connecting it to the electrical power supply to switch on. The same applies if the appliance is moved at a later date.
- The appliance must always be installed in a dry environment.
- When installing, leave at least 10 cm clearance to the rear and to the left and right for adequate ventilation. Leaving less room for ventilation may affect efficiency.
- We strongly recommend installing the appliance in a place with good natural ventilation to increase ventilation properties.
Electrical components and other dangers
- No other appliances should be plugged into the same socket as with this appliance.
- Do not place any dangerous products, such as fuel, alcohol, paint, flammable or explosives, etc. inside or near the appliance as it may result in a fire hazard.
- Do not store any medications in the appliance.
- Wait about 5 minutes before switching on the appliance again after the appliance has been switched off or unplugged from the electrical power supply.
- Do not wash the appliance with water. Washing can cause leakage and increase the risk of electric shock. No parts/accessories can be under dishwasher.
Intended use
-
This appliance is intended for professional use.
-
This appliance is designed only to keep food or beverages, under a cool state and to display them. Any other use may lead to damage of the appliance or
personal injury. -
Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.
Grounding installation
This appliance is classified as a protection class I appliance and must be
connected to protective ground. Grounding reduces the risk of electric shock
by providing an escape wire for the electric current. This appliance is
equipped with a cord having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed and grounded.
Different operation parts
- Air duct outside the glass to remove the condensation water
Preparation before using for the first time
Remove all protective packaging and wrapping.
- Check for the completeness of the product. In case of incomplete delivery and damages. Please contact supplier (See ==> Warranty).
- Clean all components as described (See ==> Cleaning and Maintenance).
- Place all the racks inside the appliance.
Note: Due to manufacturing residues, the appliance may emit a slight odor
in the first few cycles. This is normal and does not indicate any defect or
hazard. Make
sure the appliance is well ventilated.
Operation
-
Connect the power plug with a suitable electrical outlet. Leaving the appliance for running some hours to reach the cooling temperature before
placing the beverage or food inside the appliance.
-
Digital temperature controller operation
1). Setting the temperature -
Press to enter into the setting mode. The set temperature is displayed.
-
Press or to increase or decrease the set temperature.
-
Press again to confirm the setting and exit. Then, inside cabinet temperature is displayed.
Note:
- If no button is pressed within 10 seconds. The newly set temperature will be stored.
- The temperature setting range from 2°C to 6°C (233610, 233627, 233634, 233641, 233658, 233665, 233269, 233238) ; The temperature setting range from 2°C to 8°C (233696, 233290).
- Keep the door open time as short as possible in order to keep a cool temperature inside.
2). Illumination inside the cabinet
- Press to switch ON the light. Press again to switch OFF the light.
3). Refrigerant LED indicator
- During the cooling operation (compressor enabled), this refrigerant LED indicator will light up constantly.
- After the inside cabinet reaches the set temperature, the refrigerant LED indicator will flash continuously.
- When defrost start, the refrigerant LED indicator light off.
4). Defrost LED indicator
- During the defrost operation, this defrost LED indicator will light up constantly.
- After the defrost operation, defrost LED indicator will light off.
Cleaning and Maintenance
Attention: Always unplug the appliance from the electrical power outlet before cleaning & maintenance.
Cleaning
- The exterior and interior surfaces can be cleaned with a damp cloth and a little detergent.
- Racks can be removed and washed in water.
- Do not use a water jet or steam cleaner for cleaning and do not push the appliance under the water.
- No, any parts can be cleaned in the dishwasher.
- Clean the appliance regularly.
Parts | How to clean | Remark |
---|---|---|
All accessories such as racks, rack holders, etc. |
- Soak in warm, soapy water for about 10 to 20 minutes.
- Rinse under running water thoroughly.
| Dry all parts well at last.
External glass surfaces|
- Wipe clean with a soft cloth and a little neutral detergent. Make sure no water or moisture enters inside the of the appliance.
Interior glass surfaces|
- Remove any food deposits.
- Wipe clean with a soft cloth and a little mild detergent. Make sure no water or moisture enters inside the appliance.
Glassdoor
Replacing the defective light
- Attention: Always unplug the appliance from the electrical power outlet before replacement.
- Remove both screws on the side of the light cover
- Remove the old light and replace with a new one of the same type (not included). [Fluorescent tube 220-240V~ /50Hz 11W]
- Reassemble the light cover.
- If you do not sure how to replace it, contact the supplier/ service provider (See ==> Warranty).
Putting the appliance out of reach for a long period of time
- Attention: Always unplug the appliance from the electrical power outlet.
- Remove all the food and beverage inside the appliance.
- Clean the appliance as described in Cleaning. (See ==> Cleaning).
- Store the appliance in a cool, clean place and keep it out of reach of the children.
Troubleshooting
If the appliance does not function properly, please check the below table for
the solution. If you are still unable to solve the problem, please contact the
supplier/service provider.
Problems
| Possible cause|
Possible solution
---|---|---
The appliance does not start cooling after connect to electrical power
supply.| Thermal cut-out activated| Contact with the supplier/service provider
for repair.
The compressor is defective.
The power plug is connected correctly with the power supply outlet.| Check the
connection and make sure all the connections are correctly connected.
Cooling is not enough.| The appliance is under strong sunlight radiation or
close to a heat source.| Move the appliance to a new location to avoid direct
sunlight.
The doors are not properly closed or the sealing gasket is defective.| Close
the doors properly.
Too much food is placed inside the appliance.| Placeless food inside the
appliance.
Surrounding ventilation is insufficient.| Check that if sufficient ventilation
is provided by allowing at least 10cm away from other objects or walls.
Too much noise| The appliance is not placed horizontally.| Check to make sure
the appliance is placed horizontally.
The appliance touches the surrounding wall or other objects.| Check to make
sure that at least
10cm away from other objects or walls.
There are some loose parts inside the appliance.| Contact the supplier/service
provider for repair.
Technical specification
Item no.| 233610 I| 233627 I| 233634| I 233238 I| 233641 I| 233658
I| 233665| 233269| 233696 I| 233290
---|---|---|---|---|---|---|---|---|---|---
Operating voltage and frequency| 220•240V- /501-1z
Rated input power| 170W| 170W| I 170W| I 170W| 170W| 170W| I 210W| 210W|
380W I| 380W
Setting temperature| Setting from 2°C to 6 C| Setting from 2°C to 8°C
Net weight (approx.’| 32kg| 32kg| 35kg| 35kg| 36kg| 36kg| 40kg| 40kg| 90kg|
90kg
Rated Current| 1.4A| 1.4A| 1.4A| 1.4A| 1.4A| 1.1A| 1.5A| 1.5A| 2.4t,| 2.4A
Protection class| Class I
Climate class| 4
Refrigerant used and injection quantity| R600a/ 40g| R290/100g
Illuminate light| LED 2.6W| LED 4W
Noise level| < 60 dB (Al
Colour| White| I Black| White| Black| White| I Black| White| I Black|
White| I Black
Inside cabinet capacity| 58L| 68L| 78L| 98L| 270L
Outer dimension| 452 x 406 x (HI816mm| 452 x 406 x 00891mm| 452 x 406 x 00
966mm| 452 x 406 x 0111116mm| 556 x 526 x 110 1913mm
Remark: Technical specification is subjected to change without prior notification
Circuit diagram (Item 233238, 233269, 233610, 233627, 233634, 233641,
233658, 233665)
Circuit diagram (Item 233290, 233696)
Warranty
Any defect affecting the functionality of the appliance which becomes apparent
within one year after purchase will be repaired by free repair or replacement
provided the appliance has been used and maintained in accordance with the
instructions and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under warranty, state
where and when it was purchased and include proof of purchase (e.g. receipt).
In line with our policy of continuous product development, we reserve the
right to change the product, packaging, and documentation specifications
without notice.
Discarding & Environment
When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment, and ecological disposal, either directly or through a public system.
Hendi Food Service Equipment GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu
Hendi HK Ltd.
1208, 12/F Exchange Tower
33 Wang Chiu Road, Kowloon Bay, Hong Kong
Tel: +852 2154 2618
Email: info-hk@hendi.eu
Find Hendi on internet:
www.hendi.eu
www.facebook.com/HendiToolsforChefs
www.linkedin.com/company/hendi-food-service-
equipment-b.v.
www.youtube.com/HendiEquipment
– Changes, printing, and typesetting errors reserved.
© 2020 Hendi B.V. De Klomp – The Netherlands
Ver: 28-12-2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>