TELTONIKA RUTX14 Industrial Cellular Router User Guide

: June 7, 2024
: teltonika

Table of Contents

FRONT VIEW
BACK VIEW
POWER SOCKET PINOUT
HARDWARE INSTALLATION
LOGIN TO DEVICE
TECHNICAL INFORMATION
SAFETY INFORMATION

Quick Start Guide v1.1

http s://wiki .teltonika-networks.com

Wiki Knowledge base

FRONT VIEW

BACK VIEW

POWER SOCKET PINOUT

HARDWARE INSTALLATION

Pull out the SIM needle from the front panel of the router and push the SIM holder button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
Attach all antennas.
Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.

To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router’s WebUI before you change the password.
When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router’s main operating parameters.
Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TECHNICAL INFORMATION

Radio specifications

RF technologies| 3G, 4G, GNSS, WiFi, BLE
Max RF power| 24 dBm@WCDMA, 23 dBm@LTE, 23 dBm@WiFi 10 dBm@BLE

**Bundled accessories specifications***

Power adapter| Input: 0.6 A@100-240 VAC, Output: 12 VDC, 1.5 A, 4 pin plug
Mobile antenna| 698~960 / 1710~2690 MHz, 50 Ω, VSWR<3, gain 3 dBi, omnidirectional, SMA male connector
GNSS antenna| 1575.42~1602 MHz, 2.2~5 VDC, VSWR<1.5, active total gain 28 dB (typ.), RHCP polarization, SMA male connector
WiFi antenna| 400~2483.5 MHz/5150~5905 MHz, 50 Ω, VSWR<2.0, gain 3.0 dBi, omnidirectional, RP-SMA male connector
BLE antenna| 2400~2500 MHz, 50 Ω, VSWR<2.5, gain 2.5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

SAFETY INFORMATION

RUTX14 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Hereby, TELTONIKA NETWORKS declares that this RUTX14 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following Internet address: https://wiki.teltonika- networks.com/view/RUTX14_CE/RED

[EN] Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com/

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

This sign means that product meets the requirements of the applicable EU directives.

Documents / Resources

| TELTONIKA RUTX14 Industrial Cellular Router [pdf] User Guide
RUTX14, Industrial Cellular Router
---|---
| TELTONIKA RUTX14 Industrial Cellular Router [pdf] User Guide
RUTX14 Industrial Cellular Router, RUTX14, Industrial Cellular Router, Cellular Router, Router