AcuRite 01098CDI Weather Forecaster Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
DESIGNED TO WORK FOR YOU
ITEM#661262
Weather Forecaster
model# 01098CDI
Instruction Manual
Overview
Introduction
Thank You for purchasing this AcuRite® product. Please read through this
manual in itʼs entirety to fully enjoy the benefits and features of this
product. Please keep this manual for future reference.
SETUP
Battery Choice & Temperature Range
Extended periods of cold temperatures ( below -4ºF / -20ºC ) can cause
alkaline batteries to function improperly. This will cause the outdoor
wireless sensor to stop transmitting temperature readings. Use lithium
batteries in these low-temperature conditions to ensure continued operation
for wireless sensors placed outdoors. NOTE: Rechargeable batteries are not
recommended due to higher operating voltages.
A/B/C Wireless Selection
To allow for more than one weather station and wireless sensor network to be
used in close proximity, the display unit, and the wireless sensor have a
small switch labeled “A B C” within the battery compartments. This switch
selects one of 3 wireless modes to use, and both switches MUST be set in
matching positions (either A, B, or C) for wireless communication to take
place successfully.
Installing Batteries – Wireless Sensor
Remove the battery compartment cover.
Install 2 fresh “AA” batteries as shown here.
Replace the battery compartment cover. BATTERIES MUST BE INSTALLED FOR THE
SENSOR TO OPERATE
Installing Batteries – Display Unit
Remove the battery compartment cover.
About the Intelli-Time® Clock
This weather station is equipped with Intelli-Time ® technology. Intelli-Time
clock adjusts itself for Daylight Saving Time (DST). All you need to do is
select your Time Zone and Daylight Saving Time preferences.
Display Unit: Basic Setup
Press and hold the “ ” (SET) button for 3 seconds to enter into SET MODE. Once
in set mode, the preference you are currently setting will blink on the
display.
To adjust the currently selected (flashing) preference item, press the “ ∧”
or “∨ ” buttons. (press and HOLD to fast adjust).
To save your adjustments, press the “ ” button again to move on to adjusting
the next preference. The preference set order is as follows:
TIME ZONE (PST MST CST EST AST HAST AKST) REQUIRED
DST (Daylight Saving Time ON or OFF) REQUIRED
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE SCALE (ºF or ºC)
BAROMETRIC PRESSURE SCALE (inHg or hPa)
You will automatically exit SET MODE if no buttons are depressed for 30
seconds. You may enter basic setup mode again at any time by pressing the “ ”
button.
Basic Setup is Now Complete
The sensor will soon send a signal to the display unit and the two units will
be synchronized. It may take a few minutes for synchronization to be complete.
PLACEMENT
Now that setup is complete, you must choose a location to place the sensor and
the display unit. The sensor MUST be placed less than 330 feet (100 meters)
away from the display unit.
This weather station uses radiofrequency for communication, which is
susceptible to interference from other electronic devices and large metallic
items or thick walls. Always place both units at least 3 feet (.91 m) away
from appliances ( TV, microwave, radios, etc. ) or objects that may interfere
with the wireless communication ( large metal surfaces, thick stone walls,
etc. ).
Placement of Display Unit
Place the display unit in a dry area free of dirt and dust. To help ensure an
accurate indoor temperature and humidity measurement, be sure to place the
display unit out of direct sunlight, and away from any heat sources or vents
in your home. There are 2 placement options for the display unit. You may hang
the main unit on a wall using the integrated hang hole. Alternatively, you may
place the main unit on a tabletop or other flat surface using the included
tabletop display stand.
Placement of Sensor
The outdoor sensor MUST BE PLACED OUTDOORS to observe outdoor temperatures and
humidity. The sensor must be placed less than 330 feet (100 m) from the
display unit. The sensor is water-resistant and is designed for general
outdoor use. However, to extend the life of the product, place the sensor in
an area protected from direct weather elements.
To ensure an accurate outdoor temperature measurement, be sure the sensor is
placed out of direct sunlight and away from any heat sources.
There are 2 placement options for the sensor. You may hang it using one of the
two integrated hang holes, or use string (not included) to hang it from a
suitable location like a well-covered tree branch.
USE
A.
Daily High & Low
The daily high and low records are displayed for the outdoor temperature and
humidity. These records are automatically cleared daily at midnight.
B. Wireless Signal Reception Icon
The display unit has a signal reception icon near the outdoor temperature
display area. If there are a low number of “bars” present, you may experience
no temperature display ( “- -” ) or inaccuracy. In either case, you may need
to relocate one or both of the units. If most or all 4 of the bars are
present, wireless reception is good and no action is required.
C. Forecast Icon
This feature gives you the predicted weather forecast for the next 12 to 24
hours based on an advanced algorithm that includes barometric pressure and
temperature. This weather station will provide the most accurate forecast that
a single station weather instrument can provide.
D. 14-Day Learning Mode
This weather station has a patented 14-day “Learning Mode” calibration
process. During this Learning Mode, the weather station will make altitude
calculations that may affect the accuracy of the forecast. Once the Learning
Mode process is complete, the Learning Mode icon will disappear from the
display unit and the weather forecast is ready for superior operation.
E. Atmospheric Pressure: History & Current
This weather station has a pressure graph that tracks and displays the barometric pressure 12-hours in the past and displays the current barometric pressure. Additionally, the graph will automatically display the “FALLING”, “STEADY” OR “RISING” icon and a curve to represent the rate of change over the previous 12-hour time period.
About Atmospheric Pressure
Atmospheric Pressure is defined as the pressure at any location on the Earth,
caused by the weight of the column of air above it. At sea level, atmospheric
pressure has an average value of one atmosphere and gradually decreases as
altitude increases. Also called barometric pressure.
The weight of the atmosphere that envelopes Earth exerts pressure on all
points of the planet’s surface. Meteorologists use barometers to measure this
atmospheric pressure (also called barometric pressure). At sea level, the
atmospheric pressure is approximately 1 kilogram per square centimeter (14.7
pounds per square inch), which will cause a column of mercury in a mercury
barometer to rise 760 millimeters (30.4 inches). Variations in atmospheric
pressure greatly affect the weather. Low pressure generally brings rain. In
areas of low air pressure, the air is less dense and relatively warm, which
causes it to rise. The expanding and rising air naturally cools, and the water
vapor in the air condenses, forming clouds and the drops that fall as rain.
In high-pressure areas, the air is dense and relatively cool, which causes it
to sink. The water vapor in the sinking air doesnʼt condenses, resulting in
clear skies.
TROUBLESHOOTING
| Problem | Possible Solution(s) |
|---|
Low or NO Wireless Sensor
Reception
low reception
NO reception
no bars and flashing – – ” temp/humidity data| Relocate the display console
and/or the wireless sensor. Both units must be within 330 feet (100 meters)
from each other. Make sure both units are placed at least 3 feet (.91 m) from
other electronic appliances and devices that may interfere with the wireless
communication (such as TVs, microwaves, computers etc). NOTE: It may take up
to 20 minutes for the display console to re-synchronize with the sensor when
batteries are replaced. Use lithium batteries in the sensor when the
temperature is below -4°F (.20°C) Make sure the A-B-C switch selection in the
battery compartments of the display unit and sensor matches.
Forecast Seems Inaccurate| As with any weather forecast, 100% accuracy is not
possible. However, this weather station has a patented “fourteen-day learning
mode” calibration process. During this learning mode, the weather station will
make altitude calculations that may affect the accuracy of the forecast. Once
the 14-day learning mode process is complete, the learning mode icon will
disappear and the weather forecast should be ready for superior operation.
Make sure the wireless outdoor sensor is placed outdoors and is placed in a
location that will most accurately report the outside temperature and humidity
conditions, these readings directly affect the forecast feature.
Display Console Screen Not Working| The display may fail to start properly due
to static discharge.
Batteries may need replacing.
Check that battery are correctly installed.
Press the reset button located within the battery compartment of the display
unit to reset the entire unit. Please note that all of the date and time
information will need to be entered manually after a reset.
Set Wireless ID
This wireless weather station uses a long-range 433mhz radio frequency for
communication. In the event that you have reception problems due to
interference, both the display unit and the wireless sensor have a selectable
wireless ID.
The ID switches are located within the battery compartments of the display
unit and the wireless sensor.
You may choose A, B or C; but both the display unit and the wireless sensor
IDs must match for successful synchronization.
Have questions about product setup or operation? We’re here to help!
24/7 Support: www.acurite.com
- Product Setup & Demo Videos
- Product Manuals
- Frequently Asked Questions
- Register your Product
- Support Forum
- Submit Feedback & Ideas
SPECIFICATIONS
Batteries: 5 x “AA:’ (included)
Lithium Batteries Recommended in Outdoor Sensor if temperatures are below-4°F
Measurement Ranges
Outdoor Temperature: -40°F to 158°F,-40°C to 70°C
Outdoor Humidity: 1% to 99%
Indoor Temperature: 32°F to 122°F, 0°C to 50°C
Wireless Range: 330 ft/1oo m MAX
Depending on home construction materials
ITEM# 661262
MADE IN CHINA
model#
01098CDI
Limited One
Year Warranty Instructions & Warranty Enclosed
Customer Care: 877-221-1252
www.AcuRite.com
Imported by:
Costco Wholesale Corporation
PO Box 34535
Seattle, WA 98124-1535
The U.S.A.
1-800-774-2678
shop at www.costco.com
Patent numbers: 5,978,738; 6,076,044; 6,597,990; US 7,637,141 B2
AcuRite® is a reg_istered trademark of the Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior
to battery installation. Remove batteries from equipment that is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the
battery compartment. Promptly remove dead batteries from the device. Dispose
of used batteries properly. Only batteries of the same or equivalent type as
recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose
of batteries in are, as batteries may explode or leak. DO NOT mix old and new
batteries or types of batteries (alkaline/standard). DO NOT use rechargeable
batteries.
DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply
terminals.
LIMITED ONE YEAR WARRANTY
Chaney Instrument Company warrants that all products it manufactures to be of
good material and workmanship and to be free of defects if properly installed
and operated for a period of one year from the date of purchase. REMEDY FOR
BREACH OF THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIR OR REPLACEMENT OF
DEFECTIVE ITEMS. Any product which, under normal use and service, is proven to
breach the warranty contained herein within ONE YEAR from the date of sale
will, upon examination by Chaney, and at its sole option, be repaired or
replaced by Chaney. In all cases, transportation costs and charges for
returned goods shall be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This warranty will
not be breached, and Chaney will give no credit for products it manufactures
which shall have received normal wear and tear, been damaged, tampered with,
abused, improperly installed, damaged in shipping, or repaired or altered by
others than authorized representatives of Chaney.
THE ABOVE-DESCRIBED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND ALL OTHER WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. CHANEY EXPRESSLY
DISCLAIMS ALL LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES,
WHETHER ARISING IN TORT OR BY CONTRACT FROM ANY BREACH OF THIS WARRANTY. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. CHANEY FURTHER DISCLAIMS ALL LIABILITY FROM PERSONAL INJURY RELATING TO
ITS PRODUCTS TO THE EXTENT PERMITTED BY LAW. BY ACCEPTANCE OF ANY OF CHANEY’S
EQUIPMENT OR PRODUCTS, THE PURCHASER ASSUMES ALL LIABILITY FOR THE
CONSEQUENCES ARISING FROM THEIR USE OR MISUSE. NO PERSON, FIRM OR CORPORATION
IS AUTHORIZED TO ASSUME FOR CHANEY ANY
OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS PRODUCTS. FURTHERMORE, NO
PERSON, FIRM OR CORPORATION IS AUTHORIZED TO MODIFY OR WAIVE THE TERMS OF
THIS PARAGRAPH, AND THE PRECEDING PARAGRAPH, UNLESS DONE IN WRITING AND SIGNED
BY A DULY AUTHORIZED AGENT OF CHANEY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
For in-warranty repair, please contact:
Customer Care Department
Chaney Instrument Company
965 Wells Street
Lake Geneva, WI 53147
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Imported by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA98124-1535
The U.S.A.
1-800-77 4-2678
Shop at www.costco.com
01098CDI INST 060512
References
- AcuRite Weather Monitoring | #1 Weather Station Brand in North America
- AcuRite Weather Monitoring | #1 Weather Station Brand in North America
- Welcome to Costco Wholesale
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>