ACURITE 00609 Weather Thermometer Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
DESIGNED TO WORK FOR YOU
Weather Thermometer
mode/#00609
Instruction Manual
Overview
Introduction
Thank You for purchasing this Acurite® product. Please read through this
manual in it’s entirety to fully enjoy the benefits and features of this
product. Please keep this manual for future reference.
NOTE: A clear film is applied to the LCD at the factory that must be removed
prior to using this product. Locate the clear tab and simply peel to remove.
SETUP
Battery Choice & Temperature Range
Extended periods of cold temperatures ( below -4°F / -20°C ) can cause
alkaline batteries to function improperly. This will cause the outdoor
wireless sensor to stop transmitting temperature readings. Use lithium
batteries in these low-temperature conditions to ensure continued operation
for wireless sensors placed outdoors. NOTE: Rechargeable batteries are not
recommended due to higher operating voltages.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior
to battery installation. Removebattteriesfrom equipment which is not to be
used for an extended period of lime. Follow the polarity(+/-) diagram in the
battery compartment. promptly removedead batteries from the device. Dispose
of used batteries properly. Only batteries of the same or equivalent type as
recommended are to be used. DO NOT incinerate used batteries.DONOTdisposeof
batteries in a fire. as batteries may explode or leak. DO not mix old and new
batteries or types of batteries (alkaline/standard). NOT DO use rechargeable
DO recharge batteries. NOT non-rechargeable DO short-circuit the supply
terminals.
A/B/C Wireless Selection
To allow for more than one display and wireless sensor network to be used
in close proximity, the display unit, and the wireless sensor has a small
switch labeled “A B C” within the battery compartments. This switch selects
one of 3 wireless modes to use, and both switches MUST be set in matching
positions (either A, B, or C) for wireless communication to take place
successfully.
Installing Batteries – Wireless Sensor
Remove the battery compartment cover. Install 2 fresh “AA” batteries as shown
here. BATTERIES MUST BE INSTALLED FOR
THE SENSOR TO OPERATE
Installing Batteries – Display Unit
Remove the battery compartment cover.
Install 3 fresh “AA” batteries into the battery compartment.
Replace the battery compartment cover.
PLACEMENT
Now that setup is complete, you must choose a location to place the wireless
sensor and the display unit. The wireless sensor MUST be placed less than 330
feet ( 100 meters} away from the display unit.
This wireless thermometer uses radiofrequency for communication, which is
susceptible to interference from other electronic devices and large metallic
items or thick walls. Always place both units at least 3 feet (.91 m} away
from appliances ( TV, microwave, radios, etc. } or objects that may interfere
with the wireless communication ( large metal surfaces, thick stone walls,
etc. ).
Placement of Display Unit
Place the display unit in a dry area free of dirt and dust. To help ensure an
accurate indoor temperature and humidity measurement, be sure to place the
display unit out of direct sunlight, and away from any heat sources or vents
in your home. There are 2 placement options for the display unit. You may hang
the main unit on a wall using the integrated hang hole. Alternatively, you may
place the main unit on a tabletop or other flat surface using the included
detachable tabletop display stand.
Placement of Sensor
The wireless sensor MUST BE PLACED OUTDOORS to observe outdoor temperatures
and humidity. The wireless sensor must be placed less than 330 feet ( 100 m)
from the display unit. The wireless sensor is water-resistant and is designed
for general outdoor use.
However, to extend the life of the product, place the wireless sensor ‘life in
an area protected from direct weather elements.
To ensure an accurate outdoor temperature measurement, be sure the wireless
sensor is placed out of direct sunlight and away from any heat sources.
There are 2 placement options for the wireless sensor. You may hang it using
one of the two integrated hang holes, or use string (not included) to hang it
from a suitable location like a well-covered tree branch.
USE
Main Unit Detachable Stand
Included with the main unit is a detachable stand for tabletop placement.
Features
TROUBLESHOOTING
| Problem | Possible Solution |
|---|
Bad Wireless Sensor Reception
no bars| Relocate the main unit and/or the wireless sensor. Both units must be
within 330 feet (100m) from each other. Make sure both units are placed at
least 3 feet (.91 m) from other electronic appliances and devices that may
interfere with the wireless
communication (such as TVs, microwaves, computers, etc). NOTE: It may take up
to 20 minutes for the main unit to re-synchronize with the sensor when
batteries are replaced. Use lithium batteries in the sensor when the
temperature is below -4°F (-20°C).
No Wireless Sensor Data
(no communication)
no bars and flashing e ” – ” data| If wireless reception is bad (no bars), see
the “Bad Reception” section above. The wireless ID setting on each unit must
match for all units to communicate properly. See “Set Wireless ID” on the next
page.
Display Console
Screen Not Working| Make certain that the batteries are installed
correctly.
Batteries may need replacing
Please DO NOT return the product to the retail store.
For technical assistance and product return information, please call Customer
Care: 877-221-1252 Mon. – Fri. 8:00
A.M. to 4:30 P.M. ICST]
www.chaneyinstrument.com
Set Wireless ID
This
wireless thermometer uses a long-range 433mhz radio frequency for
communication.
In the event that you have reception problems due to interference, both the
display unit and the wireless sensor have a selectable wireless ID.
The ID switches are located within the battery compartments of the display
unit and the wireless sensor.
You may choose A, B or C; but both the display unit and the wireless sensor
IDs must match for successful synchronization.
SPECIFICATIONS
Product Facts
Batteries: 5 x “AP:’ (not included) Lithium Batteries Recommended in Outdoor
Sensor if temperatures are below-4°F
Measurement Ranges
color Temperature: -40°F to 158°F -40°C to 70°C
Outdoor Humidity: 1% to 99% RH
Indoor Temperature: 32°F to 122°F 0°C to 50°C
Indoor Humidity: 16% to 98% RH
Wireless Range: 330 ft / 100 m MAX
Depending on home construction materials
MADE IN CHINA
HECHO EN CHINA
Limited One
Year Warranty
Instructions &
Warranty Enclosed
Customer Care:
877-221-1252
www.chaneyinstrument.com
LIMITED ONE YEAR WARRANTY
Chaney Instrument Company warrants that all products it manufactures be of
good material and workmanship and to be free of defects if properly installed
and operated for a period of one year from the date of purchase. REMEDY FOR
BREACH OF THIS WARRANTY IS EXPRESSLY LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE ITEMS. Any product which, under normal use and service, is proven to
breach the warranty contained herein within ONE YEAR from the date of sale
will, upon examination by
Chaney, and at its sole option, be repaired or replaced by Chaney. In all
cases, transportation costs and charges for returned goods shall be paid for
by the purchaser. Chaney hereby disclaims all responsibility for such
transportation costs and charges.
This warranty will not be breached, and Chaney will give no credit for
products it manufactures which shall have received normal wear and tear, been
damaged, tampered with, abused, improperly installed, damaged in shipping, or
repaired or altered by others than authorized representatives of Chaney.
THE ABOVE-DESCRIBED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND ALL OTHER WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. CHANEY EXPRESSLY
DISCLAIMS ALL LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES,
WHETHER ARISING IN TORT OR BY CONTRACT FROM ANY BREACH OF THIS WARRANTY. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. CHANEY
FURTHER DISCLAIMS ALL LIABILITY FROM PERSONAL INJURY RELATING TO ITS PRODUCTS
TO THE EXTENT PERMITTED BY LAW. BY ACCEPTANCE OF ANY OF CHANEY”S EQUIPMENT OR
PRODUCTS, THE PURCHASER ASSUMES ALL LIABILITY FOR THE CONSEQUENCES ARISING
FROM THEIR USE OR MISUSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO
ASSUME FOR CHANEY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS
PRODUCTS. FURTHERMORE, NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO MODIFY
OR WAIVE THE TERMS OF THIS PARAGRAPH, AND THE PRECEDING PARAGRAPH, UNLESS DONE
IN WRITING AND SIGNED BY A DULY AUTHORIZED AGENT OF CHANEY. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
For in-warranty repair, please contact:
Customer Care Department
Chaney Instrument Company
965 Wells Street
Lake Geneva, WI 53147
Chaney Customer Care
877-221-1252
Mon-Fri 8:00 a.m. to 4:30 p.m. CST
www.chaneyinstrument.com
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Current the equipment into an outlet on a circuit different from that to which the receiver 1s connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
06095B 060111
Patent numbers: 5,978,738; 6,076,044; 6,597,990; US 7,637,141 B2 ACURITE® is a
registered trademark of the Chaney Instrument Co.
Lake Geneva, WI
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>