BL-6 JOT Desk U-Shape Workstation

“`html

Product Information

Specifications:

• Product Name: BL-6 JOT Desk U-Shape Workstation
• Main Surface Width: 54 inches
• Includes Add-Ons: A1 Surface-Mount Cable Management Tray, A2
  Modesty Panel, A3 Laminate Inset End Panels, A4 Steel Inset End
  Panels

Product Usage Instructions:

Parts List:

• 2 Main Surface
• 1 Bridge Surface
• 2 Long Beam
• 4 Lock Plate
• 8 Cap Screw
• 2 Locking Screw and Lever
• 4 30 End Leg
• 12 Wood Screws
• 2 24 End Leg
• 6 Wood Screws
• 1 or 3 42 Support Bar*
• 20 Wood Screws
• 4 Flat Bracket

Installation Steps:

Step 1: Join Main Surface 30 End Legs with Beam

Insert beam tabs into leg brackets. Hammer beam to lock in
place.

Step 2: Bolt Down Beam-to-Leg Lock Plate

Note: Ensure there is no gap between the beam and leg for proper
fit.

Frequently Asked Questions (FAQ):

Q: Are additional parts required for setting up multiple

U-Shape workstations?

A: Yes, additional parts will be needed for each additional
U-Shape workstation.

Q: What is the maximum width of the main surface included in

the package?

A: The main surface included is 54 inches wide.

“`

BL-6
JOT Desk
U-Shape Workstation
Includes Add-Ons: A1 | A2 | A3 | A4 General Installation Guide

TABLE OF CONTENTS

Edition Code
BL-6-1 :: JOT U-Shape………………………………………………………………….. 1 BL-6-2 :: JOT U-Shape with 72″ Surface……………………………..7 BL-6-3 :: JOT U-Shape with Steel Storage ……………………… 15
Add-ons
A1 :: Surface-Mount Cable Management Tray …………….. 23 A2 :: Modesty Panel ……………………………………………………………………27 A3 :: Laminate Inset End Panels……………………………………………. 31 A4 :: Steel Inset End Panels…………………………………………………… 35

Workstation with 54″ W Bridge Surface or Smaller Overview
JOT U-Shape Workstation
All parts listed are for a U-Shape workstation; additional parts will be needed for additional U-Shape workstations.
1

54″ W BRIDGE OR SMALLER

Parts List

Code

Qty.

Description

GBXXXX

2

Main Surface

GBXXXX BLPB2

1

Bridge Surface

2

Long Beam

4

Lock Plate

8

Cap Screw

2

Locking Screw and Lever

BL30

4

30″ End Leg

12

Wood Screws

BL24

2

24″ End Leg

6

Wood Screws

BASB72 BFB1

1 or 3 42″ Support Bar*

20

Wood Screws

4

Flat Bracket

*Support bars will be added to surfaces 72″ and longer.

2

54″ W BRIDGE OR SMALLER

1 | Join Main Surface 30″ End Legs with Beam
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between beam and legs. Using a rubber mallet, hammer beam to lock in place.
2 | Bolt Down Beam-to-Leg Lock Plate
Note: Beam lock plates will not fit if there is a gap between beam and leg.
3

54″ W BRIDGE OR SMALLER

3 | Measure and Adjust Beam Width
Measure from end leg to end leg until you find the approximate width of work surface. Insert the screw through overlapping beam slots and into locking screw and lever. Slightly tighten screw. DO NOT fully tighten. Insert beam grommet covers.
4 | Secure Main Surface
Position surface on frame. Align outer sides of surface flush and parallel with outer sides of end legs, adjust if not flushed. Insert wood screws into leg brackets and secure to underside of surface.
Align Flush
Align Flush
4

54″ W BRIDGE OR SMALLER

5 | Secure Support Hardware to Main Surface for Bridge Surface
Using wood screws for each flat brackets secure brackets to edge of main surface with half of brackets extended over edge of surface. Using wood screws, secure support bar to underside of surface centered between flat brackets.
6 | Attach Bridge to Main Surface
Align return surface with main surface and secure flat plates and supported bar with wood screws into underside of surface. Tighten screw on main profile beam.
5

END OF 54″ W BRIDGE OR SMALLER SECTION

7 | Attach Second Workstation to Bridge
Align second workstation with return so that back edge is flush. Secure flat brackets with wood screws into underside of both surfaces. Insert final wood screws and tighten beam locks.
8 | 9 | Secure Extra Support Bars
NOTE: Support bars will be added to surfaces 72″ and longer. Place support bars as shown below and secure to underside of surface using wood screws. Tighten screw on main profile beam.
6

Workstation with 60″ W or Longer Bridge Surface
Overview
JOT U-Shape Workstation
All parts listed are for a U-Shape workstation; additional parts will be needed for additional U-Shape workstations.
7

60″ W BRIDGE OR LONGER

Parts List

CODE

QTY

Description

GBXXXX

1

Main Surface

GBXXXX
BB3 & BBC1
BLPB2 BL30

1

Bridge Surface

2

Extra Long Beam

4

Lock Plate

8

Cap Screw

2

Locking Screw and Lever

1

Long Low Profile Beam

2

30″ End Leg

12

Wood Screws

BL24

1

24″ End Leg

6

Wood Screws

BASB72 BFB1

2

42″ Support Bar*

20

Wood Screws

4

Flat Bracket

*Support bars will be added to surfaces 72″ and longer.

8

60″ W BRIDGE OR LONGER

1 | Join Main Surface 30″ End Legs with Beam
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between the beam and legs. Using a rubber mallet, hammer beam to lock in place.
2 | Bolt Down Beam-to-Leg Lock Plate
Note: Beam lock plates will not fit if there is a gap between beam and leg.
9

60″ W BRIDGE OR LONGER

3 | Measure and Adjust Beam Width
Measure from end leg to end leg until you find the approximate width of work surface. Insert screw through overlapping beam slots and into locking screw and lever. Slightly tighten screw. DO NOT fully tighten. Insert beam grommet covers.
4 | Attach Connector Brackets to BB3 Beam
Place beam connector on the facing edges of each frame. Guide beam tabs into bracket holes, ensuring that there is not a gap between beam and leg. Using a rubber mallet, hammer beam to lock in place.
10

60″ W BRIDGE OR LONGER

5 | Secure First Surface
Position surface on frame. Align outer sides of surface flush and parallel with outer sides of end legs. Adjust beam positions if sides are not flush. Fasten surface to frame with wood screws through leg brackets into underside of surface.
Align Flush
Align Flush
6 | Secure Second Surface
Position second surface on frame. Align outer sides of surface flush and parallel with outer sides of end legs. Adjust beam positions if sides are not flush. Fasten surface to desk frame with wood screws through leg brackets into underside of surface.
Align Flush
Align Flush
11

60″ W BRIDGE OR LONGER

7 | Secure Bridge Surface
Secure flat brackets to edge of each surface, facing towards inside of workstation, with half of brackets extended over edge surface. Place final surface over exposed beam and align with back edge of workstation and secure with wood screws to flat brackets.

8 | Tighten Beam Locks

Align Flush

12

60″ W BRIDGE OR LONGER

9 | Secure Support Bars
NOTE: Support bars will be added to surfaces 72″ and longer. Place support bars as shown below and secure to underside of surface using wood screws.
13

14

END OF 60″ W BRIDGE OR LONGER SECTION

Workstation with Steel Storage Overview
JOT U-Shape Workstation All parts listed are for a U-Shape workstation
with steel storage; additional parts will be needed for additional U-Shape workstations with steel storage.
15

STEEL STORAGE

Parts List

Code

Qty.

Description

GBXXXX

2

Main Surface

GBXXXX

1

Bridge Surface

1

Extra Long Beam

2

Lock Plate

BB3

4

Cap Screw

1

Locking Screw and Lever

BL30

3

30″ End Leg

18

Wood Screws

BASB72

1 or 2 42″ Support Bar*

20

Wood Screws

BFB1

4

Flat Bracket

BLLF42

1

Steel Lateral Storage

*Support bars will be added to surfaces 72″ and longer.

16

STEEL STORAGE

1 | Join Main Surface End Legs with Beam
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between the beam and legs. Using a rubber mallet, hammer the beam to lock in place.
2 | Bolt Down Beam-to-Leg Lock Plate
Note: The beam lock plates will not fit if there is a gap between the beam and the leg.
17

STEEL STORAGE

3 | Measure and Adjust Beam Width
Measure from end leg to end leg until you find the approximate width of the work surface. Insert the screw through the overlapping beam slots and into the locking screw and lever. Slightly tighten the screw. DO NOT fully tighten. Insert beam grommet covers.
4 | Secure Main Surface
Position surface on frame. Align outer sides of surface flush and parallel with outer sides of end legs, adjust if not flushed. Insert wood screws into leg brackets and secure to underside of surface.
Align Flush
Align Flush
18

STEEL STORAGE

5 | Secure Support Hardware to Main Surface for Bridge Surface
Using wood screws for each flat brackets secure brackets to edge of main surface with half of brackets extended over edge of surface. Using wood screws, secure support bar to underside of surface centered between flat brackets.
6 | Attach Bridge to Main Surface
Align return surface with main surface and secure flat plates and supported bar with wood screws into underside of surface. Tighten screw on main profile beam.
19

END OF STEEL STORAGE SECTION

7 | Secure Second Surface to Leg
Assemble second surface by securing 24″ leg to underside of laminate surface with wood screws.
8 | Place Storage and Desk in Position
Place second surface with leg on top of steel storage and align front and side edges of surface flush with storage piece.
Align Flush
20

STEEL STORAGE

9 | Secure L-Shape Workstation to Steel Storage Surface
Align assembled L-Shape workstations with steel storage surface so that the back edge is flush. Secure the flat brackets with wood screws into the underside of both surfaces.
Align Flush
21

END OF STEEL STORAGE SECTION

10 | Tighten Beam Locks
11 | Secure Support Bar
NOTE: Support bars will be added to surfaces 72″ and longer. Place support bar as shown below and secure to underside of surface using wood screws.
22

A1: Surface-Mount Cable Management Tray Overview
JOT L-Shape Workstation If workstations have power, refer to JOT power guide.
23

CABLE TRAY

Parts List

Code

Qty.

Description

BHCT

1

Surface-Mount Cable Management

Tray

10

Wood Screws

24

CABLE TRAY

1 | Extend Cable Tray to Desired Length
Extension range: 25″­45″.
25

END OF CABLE TRAY SECTION

2 | Attach Cable Tray to Surface
Attach cable tray using wood screws.
26

A2: Modesty Panel Overview
Jot L-Shape Workstation All parts listed are for a single modesty panel;
additional parts will be needed for additional modesty panels.
27

MODESTY PANEL

Parts List

Code

Qty.

Description

1

Laminate Modesty Panel*

GLMP 4

Machine Screws

BMPBFB

2

L-Brackets

4

Wood Screws

*For Steel Modesty Panel: components may vary, but process is similar.

28

MODESTY PANEL

1 | Secure Brackets to Modesty Panel
Connect bracket to modesty panel using screws. Secure tightly.
29

END OF MODESTY PANEL SECTION

2 | Attach Modesty Panel to Surface
Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface.
30

A3: Laminate Inset End Panels Overview
JOT L-Shape Workstation All parts listed are for a single panel; additional parts
will be needed for additional panels.
31

LAMINATE INSET END PANELS

Parts List

Code

Qty.

Description

GBEP 1

Laminate Inset End Panel

4

End Panel T-Bracket

LEPBL1

8

Self-Tapping Screws

8

Wood Screws

32

LAMINATE INSET END PANELS

1 | Secure Bracket to End Legs
Attach 4 brackets to each end leg using self-tapping screws. 1. Inset­Back of bracket will align flush with edge of leg. 2. Flush­Back of bracket will be 9/16″ from edge back edge of leg.

Align Flush
/9 16″
Align Flush

Inset Bottom View Flush Bottom View

33

END OF LAMINATE INSET END PANELS SECTION

2 | Attach End Panel
Slide end panels into place and adjust until flush with bracket. Use wood screws to secure panel to each bracket.
34

A4: Steel Inset End Panels Overview
JOT L-Shape Workstation All parts listed are for a steel inset end panel;
additional parts will be needed for additional steel inset end panels.
35

STEEL INSET END PANELS

Parts List

Code

Qty.

Description

BEP 1

Steel Inset End Panel

6

Self-Tapping Screws

36

STEEL INSET END PANELS

1 | Secure Panels to End Legs
Slide the end panel into place and adjust until either flush with outside of leg or slightly recessed.

Align Flush

Slightly Recessed

37

END OF STEEL INSET END PANELS SECTION

2 | Attach End Panel
Use 4-6 self-tapping screws to secure panel to each leg.
38

1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>