EVENT LIGHTING EVE-STUNNER400 Hybrid strobe and 36 section eye candy effect User Manual

June 7, 2024
EVENT LIGHTING

EVENT LIGHTING - logo

STUNNER400
Hybrid strobe and 36 section eye-candy effect
USER MANUAL

EVENT LIGHTING EVE-STUNNER400 Hybrid strobe and 36 section eye candy effect
-0 - - -

For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

Version: 10 (28 Sep. 2020)

www.event-lighting.com.au

Safety Instructions

Warning

  • Do not open this device, there are no user-serviceable parts inside.
  • Do not look at the light source when the device is on.
  • This unit’s housing may be hot during and after the operation.
  • Install this device in a location with adequate ventilation, at least 20 inches (50 cm) from adjacent surfaces.
  • Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
  • Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
  • Do not operate this device if the housing, lenses, or cables appear damaged.
  • Do not connect this device to a dimmer or rheostat.
  • ONLY connect this device to a grounded and protected circuit.
  • ONLY use the hanging bracket to carry this device.
  • In case of a serious operating problem, stop using immediately.
  • The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
  • Keep the device out of direct sunlight. Due to the magnifying type lens, direct sunlight can cause heat to build up and damage the unit.

Power Input and Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz. Link up to the maximum of 8A. Do not exceed this.

Product Installation

  • This device can be mounted in many orientations provided each individual device is secured by the use of the correct mounting bracket.
  • Use a safety chain when mounting this device overhead.

Overview

![EVENT LIGHTING EVE-STUNNER400 Hybrid strobe and 36 section eye candy effect

Dimensions

![EVENT LIGHTING EVE-STUNNER400 Hybrid strobe and 36 section eye candy effect

Distance 1m 2m
R 95 35
G 290 90
B 12 9
W 3300 900
RGB 375 110
Full 3400 950

Menu Operation

![EVENT LIGHTING EVE-STUNNER400 Hybrid strobe and 36 section eye candy effect

  • Menu Operation](https://manuals.plus/wp-content/uploads/2021/09/EVENT- LIGHTING-EVE-STUNNER400-Hybrid-strobe-and-36-section-eye-candy-effect-Menu- Operation.jpg)

    1. Menu – Move up a level.
    2. Up – Move selection up one item.
    3. Down – Move selection down one item.
    4. Enter – Select / Move down a level.

Menu

Display

| OptionsNalues|

Description

---|---|---
Address| A001 — A512| Set the DMX address.
Chad| 12ch/45ch/117ch| Set the DMX channel mode.
Mode| Mast/d512| Set master/slave mode.
sound| Su 0 … Su59 Se00 … Se99| Set sound active mode. Set sound sensitivity.
Auto| Au 0 … Au59 Sp 1 … Sp 9| Set auto mode.

Auto speed adjustment.

Colo| Co 1 … Co 7| Set a static color.
Muan| rEd 0 … 255 grEE 0 … 255 bluE 0 … 255 Whit 0 … 255 to 0 … 255| Red dimmer. Green dimmer. Blue dimmer. White dimmer. Strobe.
Disp| Disp/IP| Reverse display.
Ver| V10| Display software version.

Colour

|

Description

---|---
Co 1| Red + strobe
Co 2| Green + strobe
Co 3| Blue + strobe
Co 4| Red + green + strobe
Co 5| Red + blue + strobe
Co 6| Green + blue + strobe
Co 7| Red + green + blue + strobe

Master/Slave Operation
Master/Slave mode allows you to link up to 12 fixtures and operate them without a controller. In Master/Slave mode, the first fixture will control the others. To set up Master/Slave mode, connect each fixture to the previous one using a DMX cable. Leave the first fixture’s DMX input unconnected. The other fixtures will be set to slave mode automatically.

DMX Chart

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has three channel modes: 12/45/117, if we set the mode to 12 channel mode, and there are several models that need to be independently controlled, we just simply address the first fixture at 1, and the second fixture at 13, the third one at 25, etc.

  • If the devices have the same address, they will behave synchronically.
  • Display is flashing when no DMX signal is received.
MODE / CHANNEL VALUE FUNCTION
12CH 45CH 117CH
1 1 1
2
009 255
3
4
5
6
7
009 009
010 012
013 013
014 131
132 139
140 181
182 189
190 231
232 255
2 2 000
009 255 RGB 5050 strobe, slow to fast
3 3 000
4 4 000
009 009 White 3535 strobe
010 012 White 3535 strobe, slow to fast
013 013 White 3535 no strobe
014 131 White 3535 strobe, slow to fast
132 139 White 3535 no strobe
140 181 White 3535 pulse strobe from slow to fast, fade in
182 189 White 3535 no strobe
190 231 White 3535 pulse strobe from slow to fast, fade out
232 255 White 3535 no strobe
000
016 031
032 047
048 063
064 079
080 095
096 111
112 127
128 143
144 159
160 175
176 191
192 207
208 255
6 000
016 031
032 047
048 063
064 079
080 095
096 111
112 127
128 143
144 159
160 175
176 191
192 207
208 255
40 000
016 031
032 047
048 063
064 079
080 095
096 111
112 127
128 143
144 159
160 175
176 191
192 207
208 255
5 000
6 000
7 000
8 000
9 000
10 000
110 000
111 000 255
112 000 255
8 41 113
008
013 016
017 020
021 024
025 028
029 032
033 036
037 040
041 044
045 048
049 052
053 056
057 060
061 064
065 068
069 072
073 076
077 080
081 085
086 089
090 093
094 097
098 101
102 105
106 109
110 113
114 117
118 121
122 125
126 129
130 133
134 137
138 141
142 145
146 149
150 153
154 158
159 162
163 166
167 170
171 174
175 178
179 182
183 186
187 190
191 194
195 198
199 202
203 206
207 210
211 214
215 218
219 222
223 226
227 231
232 235
236 239
240 243
244 247
248 255
9 42 114
008
013 016
017 020
021 024
025 028
029 032
033 036
037 040
041 044
045 048
049 052
053 056
057 060
061 064
065 068
069 072
073 076
077 080
081 085
086 089
090 093
094 097
098 101
102 105
106 109
110 113
114 117
118 121
122 125
126 129
130 133
134 137
138 141
142 145
146 149
150 153
154 158
159 162
163 166
167 170
171 174
175 178
179 182
183 186
187 190
191 194
195 198
199 202
203 206
207 210
211 214
215 218
219 222
223 226
227 231
232 235
236 239
240 243
244 247
248 251
252 255
10 43 115
016
032 047
048 063
064 079
080 095
096 111
112 127
128 143
144 159
160 175
176 191
192 207
208 255
11 44 116
016
032 047
048 063
064 079
080 095
096 111
112 127
128 143
144 159
160 175
176 191
192 207
208 255
12 45 117

Power Technical Specifications

  • Power supply: 100-240v AC, 50/60Hz
  • Power consumption: 400W

Photometrics

  • Light Source:
    o RGB: 432x 0.2W SMD5050 RGB LEDs
    o Strobe: 90x 3W SMD3535 White LEDs, 6,500-7,500K

  • Output: 3,400 lux @ 1m, full on

  • LED Lifespan: 50,000 hours

Effects

  • Dimming: 0-100%
  • Strobe: 0-20hz

Control

  • Protocol: DMX512
  • DMX Channels: 12/45/117
  • Interface: 3-pin DMX in/out
  • Operation Modes: DMX, Manual, Auto, Sound Active, Master/Slave
  • Display: 4-digit LED display with 4-button control

Housing

  • Dimensions: 449248109mm
  • Weight: 4.55kg

Warranty
Please refer to your local dealer or contact Event Lighting Pty Ltd.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

EVENT LIGHTING User Manuals

Related Manuals