EVENT LIGHTING LM180 180W LED Spot Moving Head User Manual

: June 6, 2024
: EVENT LIGHTING

Table of Contents

Safety Instructions
Product Installation
Dimensions
Lux Chart
Colour Wheel
Menu Operation
Menu
DMX Chart
More Functions
Technical Specifications
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LM180
180W LED Spot Moving Head
USER MANUAL

EVENT LIGHTING LM180 180W LED Spot Moving Head For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
Version: 1.0 (revised 05/11/2020)

Safety Instructions

Warning

Do not open this device, there are no user-serviceable parts inside. Risk of electric shock.
Do not look at the light source when the device is on.

Caution: This unit’s housing may be hot during and after the operation.

Install this device in a location with adequate ventilation, at least 20 inches (50 cm) from adjacent surfaces.
Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
Use a safety chain when mounting this device overhead.
Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
Do not operate this device if the housing, lenses, or cables appear damaged.
Do not connect this device to a dimmer or rheostat.
ONLY connect this device to a grounded and protected circuit.
ONLY use the hanging bracket to carry this device.
In case of a serious operating problem, stop using immediately.
The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Power Input & Power Linking
This device has an auto-switching power supply work with an input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse with a fuse of the same type and rating.
Before replacing the fuse, unplug the mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

Product Installation

This device can be mounted in many orientations provided each individual device is secured by the use of the correct mounting bracket.
Use a safety chain when mounting this device overhead.

EVENT LIGHTING LM180 180W LED Spot Moving Head - fig1 |
---|---

Dimensions

EVENT LIGHTING LM180 180W LED Spot Moving Head -
Dimensions

Lux Chart

Lux chart@ 16º

2.5m	5m	7.5m	10m	20m
∅0.67	∅1.34	∅2	∅2.67	∅4
19,120	4,780	2,150	1,210	540

Colour Wheel

| Red| | Magenta
---|---|---|---
| Dark Blue| | Blue
| Green| | Orange
| Yellow| | Open

Static Gobo Wheel

|

Rotating Gobo Wheel

---|---
| Position 1| | Position 1
| Position 2| | Position 2
| Position 3| | Position 3
| Position 4| | Position 4
| Position 5| | Position 5
| Position 6| | Position 6
| Position 7| |
| Position 8| |

Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select/Move down a level.

MENU

|

DESCRIPTION

---|---
Function Mode| DMX Address| A001—AXXX| DMX Address Setting
Channel Mode| CH14| 14 Channel Mode
CH16| 16 Channel Mode
AutoRun| Internal Program-8| Internal Program
State: Master/Alone| AutoRun State
AutoRun (On/Off)| Toggle AutoRun
Music Control| Internal Program-8| Internal Program
State: Master/Alone| Sound Control State
Music Run (On/Off)| Toggle Sound Control
Option| Reset Default| Yes/III| Reset to Default Setting
Signal Set| DMX
Wireless DMX Wireless TX| Wired DMX
Wireless DMX Receiver Wireless DMX Transceiver
Pan / Tilt| Reverse Pan (On/Off)
Reverse Tilt (On/Off)
Select Pan 630°/540°/360° Select Tilt 270°/180°/90° Limit Mode OFF/CEN./R/L| Reverse Pan
Reverse Tilt
Pan Degree (540°)
Tilt Degree (270°)
Select Edge or Corner Range
UI SET| Mic Sens. 0-99%
Hold on no DMX(On/Off) Half Colour (On/Off)
Flip Display (On/Off)| Microphone Sensitivity Setting Hold or no hold When no Signal Select half Colour
Flip Display
Information| Temperature| XXX°C/°F| Current Temperature
Software
Version| V1.0—V9.9| Current Software Version
Manual
Control| Reset| All
Pan/Tilt
Colour
Gobo
Others| Reset all Settings Reset Pan/tilt Settings Reset Colour Settings Reset Gobo Settings Reset Other Settings
Channel| PAN=XXX ……| Manual Control Channel
ADVANCED (Access Code 088)| Calibration| PAN=XXX……..| Calibration

The default selection for each setting is highlighted.
Press the Up and Down buttons simultaneously for 3 seconds to reverse the display.

DMX Chart

Mode/Channel| Value|

Function

---|---|---
14| 16| |

1

|

1

| | Pan
0..255| Pan movement

2

|

2

| | Pan Fine
0..255| Fine control of pan movement

3

|

3

Vector Mode

| Value|

Function

| 15| | Colour Time
0..255| Colour speed, fast to slow
| 16| | Gobo Time
| | 0..255| Gobo speed, fast to slow

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has two-channel modes:
14/16, if we set the mode at standard 16 channels mode, and there are several models that need to be independently controlled, we just simply address the first fixture at 1, and the second fixture at 17, the third one at 33, etc.

If the devices have the same address, they will behave synchronically.
The display is flashing when no DMX signal is received.

More Functions

Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via a software upgrade box, without the need to change any mechanical parts. The upgrade box is not included in the package, if you need any further assistance please contact your authorized dealer.
Hibernation. The device will enter sleep mode is activated after a period of disconnecting the DMX signal to save power and will wake immediately when the DMX signal is sent or received again.