EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head User Manual

: June 6, 2024
: EVENT LIGHTING

Table of Contents

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head
Safety Instructions
Product Installation
Dimensions
Menu operation
- Menu
DMX Chart
More Functions
Technical Specifications
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving
Head

For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

www.event-lighting.com.au

Safety Instructions

WARNING

Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
Do not look at the light source when the device is on.

CAUTION: This unit’s housing may be hot during and after operation.

Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
Use a safety chain when mounting this device overhead.
Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
Do not operate this device if the housing, lenses, or cables appear damaged.
Do not connect this device to a dimmer or rheostat.
ONLY connect this device to a grounded and protected circuit.
ONLY use the hanging bracket to carry this device.
In case of a serious operating problem, stop using immediately.
The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Power Input
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.

Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating. Before replacing the fuse, unplug mains lead.

Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

Product Installation

This device can be mounted in many orientations provided each individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head Product
Installation

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head Product
Installation 1

Dimensions

Lux Chart

EVENT LIGHTING LM6X15 6x15W LED RGBW Zoom Wash Moving Head lux
chart

Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select / Mode down a level.

MENU	DESCRIPTION
DMX Address	DMX Address
Auto Run	Auto Run
Music Run	Program 1-8
Reset	ALL
Pan/Tilt	On/Off
Zoom	On/Off
Reverse Pan	On/Off
Reverse Tilt	On/Off
Special	R Default
Cal	Code (Password: 088)
Pan, Tilt, Colour, Gobo, Focus, Prism	Calibrate the selected channel
Temp.	XXX °C/°F
Manual Ctrl.	Pan = XXX…
Mic Sens.	0-99%
Limit Mode	Limit Mode Off/Centre/Right/Left
DMX Mode	CH15 Mode
CH13 Mode
Scan Degree	Pan Degree

DMX Chart

Channel Mode| Min

DMX

| Max

DMX

| Name| Function
---|---|---|---|---
Standard| Basic
1| 1| 0| 255| Dimmer| Dimmer 0%..100%
2| 2| 0| 31| Shutter| Shutter closed
32| 63| Shutter open
64| 95| Strobe effect, slow to fast
96| 127| Shutter open
128| 159| Pulse effect, slow to fast
160| 191| Shutter open
192| 223| Random strobe effect, slow to fast
224| 255| shutter open
3| 3| 0| 255| Pan| Pan movement
4| | 0| 255| Pan-fine| Fine control of pan movement
5| 4| 0| 255| Tilt| Tilt movement
6| | 0| 255| Tilt-fine| Fine control of tilt movement
7| 5| 0| 255| Zoom| In (near) to out (far)
8| 6| 0| 225| Pan/tilt function| Pan/tilt speed, fast to slow
226| 235| Blackout during pan/tilt functions
236| 255| TBD
9| 7| 0| 255| Red| Red 0..100%
10| 8| 0| 255| Green| Green 0..100%
11| 9| 0| 255| Blue| Blue 0..100%
12| 10| 0| 255| White| White 0..100%
13| 11| 0| 15| Macros| TBD
16| 31| Red
32| 47| Green
48| 63| Blue
64| 79| White
80| 95| Red+Green
96| 111| Red+Blue
112| 127| Red+White
128| 143| Green+Blue
144| 159| Green+White
160| 175| Blue+White
176| 191| Red+Blue+Green
| | 192| 207| | Red+Blue+Green+White
---|---|---|---|---|---
208| 223| Jump Effect
224| 239| Fading Effect
240| 255| Pulse effect
14| 12| 0| 255| Macro speed| Slow to fast
15| 13| 0| 79| Special functions| TBD
80| 84| Reset all motors
85| 87| Reset pan/tilt motor
88| 96| TBD
97| 99| Reset zoom motor
100| 109| Internal program 1
110| 119| Internal program 2
120| 129| Internal program 3
130| 139| Internal program 4
140| 149| Internal program 5
150| 159| Internal program 6
160| 169| Internal program 7
170| 179| Internal program 8
180| 189| Internal sound program 1
190| 199| Internal sound program 2
200| 209| Internal sound program 3
210| 219| Internal sound program 4
220| 229| Internal sound program 5
230| 239| Internal sound program 6
240| 249| Internal sound program 7
250| 255| Internal sound program 8

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has two channel modes:
15/13, if we set the mode at standard 13 channels mode, and there are several models need to be independently controlled, we just simply address first fixture at 1, and second fixture at 14, third one at 27, etc.

If the devices have the same address, they will behave synchronically.
Display is flashing when no DMX signal is received.

More Functions

Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via a software upgrade box, without the need to change any mechanical parts.
The upgrade box is not included in the package, if you need any further assistance please contact your authorized dealer.
Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX signal to save power and will wake immediately when the DMX signal is sent or received again.