EVENT LIGHTING ZEVPAR19X12L Lite Series LED Flat Par User Manual

: May 15, 2024
: EVENT LIGHTING

Table of Contents

Safety Instructions
Product Installation
Dimensions
Control Board Operation
Static Colour Mode
Technical Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EVENT LIGHTING ZEVPAR19X12L Lite Series LED Flat Par

EVENT LIGHTING ZEVPAR19X12L Lite Series LED Flat Par

Safety Instructions

For your safety, please read this user manual carefully before use.

Warning

Do not open this device, there are no user serviceable parts inside. Risk of electric shock.
Do not look directly at the light source from close range.
Avoid contact with the unit during operation, as the housing may become hot. Allow the fixture to cool for at least 15 minutes after turning off before touching.
Install this device in a location with adequate ventilation, at least 50cm from adjacent surfaces.
Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
Use a safety chain when mounting this device overhead.
Do not operate this device outdoors where excessive dust, heat, water, or humidity may affect it.
Do not operate this device if the housing, lenses, or cables appear damaged.
Do not connect this device to a dimmer or rheostat.
Do not operate this device at temperatures higher than 40°C (104°F).
Only connect this device to a grounded and protected circuit.
Only use the hanging bracket to carry this device.
Stop using this device immediately if a serious operating problem becomes apparent.

Coin/Button Cell Battery Safety Information

This product includes an IR remote that contains a coin/button cell battery. If the battery is swallowed, it can cause severe internal burns and, in extreme cases, can lead to death. Keep batteries away from children.

Product Installation

PAR19X12L can be mounted in many orientations, provided each individual device is secured by the use of the correct mounting bracket. Use a safety chain when mounting PAR19X12L overhead.

Dimensions

Lux Chart

lux	@40°
1m	2m
00.7	01.46
R	2,850
G	4,310
B	6,290
w	4,850
A	705
UV	2,460
Full	12,730

Control Board Operation

Menu Map

| - >| | –| | Select DMX address
---|---|---|---|---|---
| - >| | or| | Select DMX channel mode (CH-1: 6ch /
CH-2: 11ch)
| - >| | –| | Set program speed
| - >| | –| | Select built-in program
| - >| | | Select sound active mode|
| - >| | –| | Select static colour mode
(See static colour mode chart below)
| - >| | –| | Set strobe speed (Hz)
| - >| | –| | Set red colour intensity
| - >| | –| | Set green colour intensity
| - >| | –| | Set blue colour intensity
| - >| | –| | Set white colour intensity
| - >| | –| | Set amber colour intensity
| - >| | –| | Set UV colour intensity
| - >| | –| | Set dimmer speed
(nod0: fastest / nod4: slowest)
| - >| | or| | Toggle LED display on / off
| - >| | Long press “Enter” button to show current temperature| |
| - >| | | Show current software version|
| - >| | or| | Restore settings to factory default

Static Colour Mode

Value	Function
C1	Red
C2	Green
C3	Red+Green
C4	Blue
C5	Blue+Red+UV
C6	Green+Blue
C7	Red +Green+Blue+Amber+UV
C8	White
C9	Red+White
C10	Green+White
C11	Red+Amber
C12	Blue+White+UV
C13	Red + Blue+White+UV
C14	Red + Blue+White
C15	Red+Green+Blue+White+Amber+UV

DMX Chart 6 Channel Mode

Channel	Value	Function
1	000-255	Red: 0% ~ 100%
2	000-255	Green: 0% ~ 100%
3	000-255	Blue: 0% ~ 100%
4	000-255	White: 0% ~ 100%
5	000-255	Amber: 0% ~ 100%
6	000-255	UV: 0% ~ 100%

11 Chann

Channel	Value	Function
1	000-255	Master Dimmer 0% ~ 100%
2	000-255	Red: 0% ~ 100%
3	000-255	Green: 0% ~ 100%
4	000-255	Blue: 0% ~ 100%
5	000-255	White: 0% ~ 100%
6	000-255	Amber: 0% ~ 100%
7	000-255	UV: 0% ~ 100%
8	000-011	Strobe OFF
012-255	Strobe (slow-fast)
9	000-009	No Function
010-019	Program 1
020-029	Program 2
030-039	Program 3
040-049	Program 4
050-059	Program 5
060-069	Program 6
070-079	Program 7
080-089	Program 8
090-099	Program 9
100-109	Program 10
110-119	Program 11
120-129	Program 12
130-139	Program 13
140-255	Sound active mode
10	000-255	Speed of auto programs (slow

~ fast)

| Ch9 must be set between

10-139

11| 000-255| Colour fade time (jump ~ fade)| Mode must be set to “nod0”

IR Remote

In order to use the IR Remote, PAR19X12L must be in DMX mode without an active DMX connection. If a DMX signal is received, PAR19X12L will prioritise the DMX signal and ignore the IR Remote.
Use On/Off to turn PAR19X12L on or off. The current IR settings will be saved automatically when PAR19X12L is powered off and reloaded when it is turned on again. To reset to the factory default Blackout mode, long press Off.
Press R/G/B/W/A/U to light up the LEDs in red, green, blue, white, amber or UV respectively. Press a number 0-9 in the orange shaded area to select a pre-set colour.
Press + to increase the intensity of the selected colour and – to decrease the intensity of the selected colour.
Press Auto/Sound/Strobe to switch on or off Auto mode, Sound Active mode and Strobe mode, respectively.
Press Blackout to clear all the remote settings and blackout PAR19X12L.

Ir Remote