EVENT LIGHTING LM150B 150W LED Beam Moving Head User Manual

: June 6, 2024
: EVENT LIGHTING

Table of Contents

EVENT LIGHTING LM150B 150W LED Beam Moving Head User Manual
Safety Instructions
Product Installation
Dimensions
Lux Chart
Colour Wheel
Static Gobo Wheel
Menu Operation
Menu
DMX Chart
More Functions
Technical Specifications
Warranty
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EVENT LIGHTING LM150B 150W LED Beam Moving Head User Manual

EVENT LIGHTING LM150B 150W LED Beam Moving Head

LM150B

For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

Safety Instructions

Warning

Do not open this device, there are no user-serviceable parts inside. Risk of electric shock.
Do not look at the light source when the device is on.

Caution: This unit’s housing may be hot during and after operation.

Install this device in a location with adequate ventilation, at least 20 inches (50 cm) from adjacent surfaces.
Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
Use a safety chain when mounting this device overhead.
Do not operate this device outdoors or in any location where dust, excessive heat, water, or
humidity may affect it.
Do not operate this device if the housing, lenses, or cables appear damaged.
Do not connect this device to a dimmer or rheostat.
ONLY connect this device to a grounded and protected circuit.
ONLY use the hanging bracket to carry this device.
In case of a serious operating problem, stop using immediately.
The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher
temperatures.

Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz. Link up to the maximum 8A. DO NOT exceed this.

Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.

Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing
(anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

Product Installation

This device can be mounted in many orientations provided each individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

FIG 1 Product Installation

FIG 2 Product Installation

FIG 3 Product Installation

Dimensions

FIG 4 Dimensions

Lux Chart

FIG 5 Lux Chart

Colour Wheel

FIG 6 Colour Wheel

Static Gobo Wheel

FIG 7 Static Gobo Wheel

FIG 8 Static Gobo Wheel

Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select/Move down a level.

The default selection for each setting is highlighted.
Press the Up and Down buttons simultaneously for 3 seconds to reverse the display.

DMX Chart

FIG 12 DMX Chart

FIG 13 DMX Chart

FIG 14 DMX Chart

FIG 15 DMX Chart

FIG 16 DMX Chart

FIG 17 DMX Chart

FIG 18 DMX Chart

FIG 19 DMX Chart

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used
to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has two channel modes:
13/15, if we set the mode at standard 15 channels mode, and there are several models need to
be independently controlled, we just simply address first fixture at 1, and second fixture at 16,
third one at 31, etc.

If the devices have the same address, they will behave synchronically.
Display is flashing when no DMX signal is received.

More Functions

Software upgrade function via DMX cable. If there is any new firmware for this device, it
can be upgraded simply via a software upgrade box, without the need to change any mechanical parts. The upgrade box is not included in the package, if you need any further assistance please contact your authorized dealer.
Hibernation. The device will enter sleep mode if activated after a period of disconnecting
DMX signal to save power and will wake immediately when the DMX signal is sent or received again.