EVENT LIGHTING PAR12X12L 12W LED RGBWAU Parcan with IR Remote User Manual

EVENT LIGHTING PAR12X12L 12W LED RGBWAU Parcan with IR Remote User Manual

For your safety, please read this user manual carefully before use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please contact your local Kookaburra Account Manager.

Safety Instructions

Warning

• Do not open this device, there are no user serviceable parts inside. Risk of electric shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the fixture to cool for at least 15 minutes after turning off before touching.
• Install this device in a location with adequate ventilation, at least 50cm from adjacent surfaces.
• Do not operate this device, or connect this device to power, within 50cm of any flammable material.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.

Coin/Button Cell Battery Safety Information
This product includes an IR remote that contains a coin/button cell battery. If the battery is swallowed, it can cause severe internal burns and, in extreme cases, can lead to death. Keep batteries away from children.

Product Installation

PAR12X12L can be mounted in many orientations, provided each individual device is secured by the use of the correct mounting bracket. Use a safety chain when mounting PAR12X12L overhead.

Dimensions

Lux Chart

Lux chart @40″ (PAR12X12L)

 | 1m             ‘        2m| 3m| 4m| 5m
 | 00.73              01.46| 02.18| 02.91| 03.64
 | 1,445                 409| 180| 93| 70
G| 2,030          570| 250| 130| 95
B| 2,910              882| 270                   171| 126
W| 2,420                 734            322| 171| 126
A| 850                    258| 120| 66| 46
UV| 840                 264| 120| 66| 49
FULL| 8,550         2,580| 1,123       I     543| 423

Control Board Operation

Menu Map

| ->| | –| | Select DMX address
---|---|---|---|---|---
| ->| | or| | Select DMX channel mode (CH-1: 6ch / CH-2: 11ch)
| ->| | –| | Set program speed
| ->| | –| | Select built-in program
| ->| | Select sound active mode
| ->| | –| | Select static colour mode(See static colour mode chart below)
| ->| | –| | Set strobe speed (Hz)
| ->| | –| | Set red colour intensity
| ->| | –| | Set green colour intensity
| ->| | –| | Set blue colour intensity
| ->| | –| | Set white colour intensity
| ->| | –| | Set amber colour intensity
| ->| | –| | Set UV colour intensity
| ->| | –| | Set dimmer speed(nod0: fastest / nod4: slowest)
| ->| | or| | Toggle LED display on / off
| ->| ****| Long press “Enter” button to show current temperature
| ->| | Show current software version
| ->| | or| | Restore settings to factory default

Static Colour Mode

DMX Chart

6 Channel Mode

11 Channel Mode

~ fast)

| Ch9 must be set between

10-139

11| 000-255| Colour fade time (jump ~ fade)| Mode must be set to “nod0”

IR Remote

In order to use the IR Remote, PAR12X12L must be in DMX mode without an active DMX connection. If a DMX signal is received, PAR12X12L will prioritise the DMX signal and ignore the IR Remote.

Use On/Off to turn PAR12X12L on or off. The current IR settings will be saved automatically when PAR12X12L is powered off and reloaded when it is turned on again. To reset to the factory default Blackout mode, long press Off.

Press R/G/B/W/A/U to light up the LEDs in red, green, blue, white, amber or UV respectively. Press a number 0-9 in the orange shaded area to select a pre-set colour.

Press + to increase the intensity of the selected colour and – to decrease the intensity of the selected colour.

Press Auto/Sound/Strobe to switch on or off Auto mode, Sound Active mode and Strobe mode, respectively.

Press Blackout to clear all the remote settings and blackout PAR12X12L.

Technical Specifications

Photometric

• Light Source: 12x W RGBWAU 6-in-1 LEDs
• Beam Angle: 40°
• PWM: 2,000 Hz
• LED Lifespan: 50,000hours

Effects

• Dimming: 0~100%
• Strobe: 1 – 20 Hz

Power

• Input Voltage: 100~240V AC, 50/60Hz
• Power Consumption: 60W
• Connection: IEC in/out

Control

• Operation Modes: DMX, manual, auto, sound active, IR remote, master/slave
• DMX channels: 6/11

Housing

• Materials: Die cast aluminium, matte black finish
• Cooling: Fanless Cooling
• Net weight: 1.85kg

Warranty

Please contact your local Kookaburra Account Manager.

For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions.
Please contact your local Kookaburra Account Manager

Safety Instructions

WARNING

• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not connect this device to a dimmer or rheostat.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Product description

The KONTROL36 is a compact DMX controller designed for an independent control of up to six fixtures with a RGBWAU control mode.

Fixtures can be doubled up on addresses to allow control of more than six fixtures.

Control Surface

Fixtures
The KONTROL36 has six fixture buttons allowing independent control of your fixtures.
By selecting a fixture the corresponding LED will light up and the dimming sliders will then control the fixtures six
channels. Multiple fixtures can be selected at one time.

Manual RGBW
The KONTROL36 has a manual control function, selecting this mode by pressing the Manual RGBWAUbutton then, select the fixture you want to control and then you can manually adjust the colours by the 6 sliders.

Colour Fade
The KONTROL36 has a built in Colour fader program, selecting this mode will fade the colours of all selected fixtures. Speed, Fade time, Master Dimmer, Sound and sound level can be set prior or after selecting this mode.

Auto
The KONTROL36 has built in automatic random colour programs. Selecting this mode will start the program of selected fixtures. Speed, Fade time, Master Dimmer, Sound and sound level can be set prior or after selecting this mode.

Chases
The KONTROL36 has built in chase programs. Selecting this mode will start the program on selected fixtures and the mode can be change by selecting presets which are based on the following table. Speed, Fade time, Master Dimmer, Sound and sound level can be set prior or after selecting this mode.

Preset Mode
The KONTROL36 has preset colour presets, selecting this mode allows you to select the colours from the 18 buttons. First, select the fixture you want to control and then select the colour from the preset buttons. Master dimmer, fade time and speed can be set prior to selecting the colour.

Colour Macro Mode
The KONTROL36 has preset colour macros, selecting this mode allows you to select the colours from the Speed slider. First, select the fixture you want to control and then select the colour from the Speed slider. Master dimmer and fade time can be set prior and after selecting the colour.

Follow Mode
The KONTROL36 has colour follow chaser mode, selecting the Colour fade and the Auto button will active this mode. Speed, Fade time, Master Dimmer, Sound and sound level can be set prior or after selecting this mode.

Sound
The KONTROL36 has built in microphone which can be used in Auto and Chasers modes, the sensitivity can be adjusted by the sound knob.

Strobe
The KONTROL36 has built in strobe function. The rate of the strobe can be adjusted by the Strobe slider

DMX Addresses

Fixtures should be set to the following addresses to be controlled by the Kontrol36
Fixture 1 = Address 1
Fixture 2 = Address 7
Fixture 3 = Address 13
Fixture 4 = Address 19
Fixture 5 = Address 25
Fixture 6 = Address 31

TECHNICAL SPECIFICATIONS

• DMX512 protocol with 36channels
  Independent control of 6 fixtures, 6ch each (RGBWAU)
  Each fixture can be set in different playback modes simultaneously Sound- activated: synchronized music activation through internal microphone with adjustable sensitivity

• Preset: 18 color preset for an immediate operation

• Macro: Virtual color wheel to scroll the whole color spectrum
  Variable fade times for all playback modes
  Variable strobe 0-30Hz
  Slider for master dimmer
  Adjustable blackout allows fixtures to fade out

• Power: 9V DC 500mA

• MIDI Signal: 5 din pin standard interface

• Dimensions: 393 x 140 x 50 mm

• Weight: 1.5kg

WARRANTY

Please contact your local Kookaburra Account Manager.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>