TELTONIKA TRB245 M2M LTE Gateway User Guide

TELTONIKA TRB245 M2M LTE Gateway User Guide

FRONT VIEW

BACK VIEW

16 PIN CONNECTOR PINOUT

HARDWARE INSTALLATION

1. Unscrew two back panel hex bolts and remove the back panel.

2. Insert your SIM card(s) into the SIM socket(s), which are located on the bottom side of PCB.

3. Attach the panel and tighten the hex bolts.

4. Attach the mobile antenna (max torque 0.4 N·m / 3.5 lbf·in).
   
   + – 9-30 VDC positive power pin
   D1, D2, D3 – Configurable digital Input/Output pins. Open collector output, max output 30 V, 300 mA or Digital input where 0-6 V detected as logic low and 8-30 V – logic high.
   CTS – RS232 clear data to send pin (output).
   RTS – RS232 request data to send pin (input).
   R+ – RS485 receiver positive signal pin.
   D+ – RS485 driver positive signal pin.
   – – Negative/ground power pin.
   – Ground pins for D1, D2, D3, A, RS232 and RS485.
   A – Analog input pin. Analog voltage range 0-30 V.
   TX – RS232 transmitted data (input).
   RX – RS232 received data (output).
   R – – RS485 receiver negative signal.
   D – – RS485 driver negative signal.

5. Connect open PSU leads to 16 pin terminal block:
   a) red wire to top row first contact (+);
   b) black wire to bottom row first contact (-).

6. Connect the 16 pin terminal block to gateway 16 pin connector and plug other end of the power adapter into a power outlet.
   

DEVICE CONFIGURATION

1. Power on the device and connect the Ethernet cable to your computer.
2. Allow the gateway to boot up. This might take up to 60 seconds.
3. To enter the gateway Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
4. Use login information shown in image A when prompted for authentication.
5. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory, and you will not be able to interact with the gateway WebUI until you change the password.
6. When you change the gateway password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the gateway main operating parameters.
7. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
   
   

TECHNICAL INFORMATION

Radio specifications

RF technologies

|

2G, 3G, 46, GNSS

Max RF power

|

33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE

**Bundled accessories specifications***

Power adapter

|

Input 0.4 A@100-240 VAC, output 9 VDC, 1 A, connected to 16 pin terminal block

Mobile antenna

|

698-960 / 1710-2690 MHz, 50 0, VSWR <3, gain” 3 dBi, omnidirectional, SMA male connector

GNSS antenna

|

1575.42-1602 MHz, 2.2-5 VDC, VSWR < 1.5, gain** 28 dB (typ.), RHCP polarization, SMA male connector

SAFETY INFORMATION

TRB245 gateway must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Wiki Knowledge base
https://wiki.teltonika-networks.com/

The full text of the EU declaration of conformity is available at the following
Internet address: https://wiki.teltonika- networks.com/view/TRB245_CE/RED

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

  This sign means that product meets the requirements of the applicable EU directives.

http://www.teltonika-networks.com/

References

• Amazone service client telephone tel contacter contact Amazon
• Teltonika Networks - LTE Routers, Gateways & Modems for IoT
• wiki.teltonika-networks.com
• wiki.teltonika-networks.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>