enbrighten 82729 Eternity Lights Installation Guide

enbrighten 82729 Eternity Lights Installation Guide

SETUP

Test the lights

Plug your lights into an outlet. Press the pairing button on the power supply a few times to ensure all the LEDs work. Unplug the lights and follow the instructions to pair your lights with the app.

1. Remotely operate your Eternity Lights with the easy-to-use Enbrighten app. Follow the available instructions and resources to set up your smart device.

INSIDE THE BOX

INSTALLATION

Install the lights on eaves, balconies, pergolas and more using the included screws and double-sided tape. Ensure the intended surface is clean and dry before proceeding. (Scan QR code for alternate installation methods.)

NOTE: When installing, ideal temperature for tape application is between 70-100°F (21-38°C). Surface temperatures below

1. Uncoil the power supply cord (F) and Eternity Lights (A) and plan your installation. Make sure an outlet is within

2. Mount the power supply (F) using the included screws and anchors (G). Usethe power cord clips (D) to secure the power cord as needed.

3. IMPORTANT: Steps 5-8 should be done one LED puck at a time.

4. Peel the red paper backing from the tape and firmly press the combined LED puck and bracket onto the mounting

5. Attach each bracket (B) to the back of LED pucks — press until they click into

LINKING ADDITIONAL STRANDS

Link multiple sets for a total length of 200ft. (60.9m).
IMPORTANT: Linking strands over 150ft. (45.5m) will lead to reduced lumen output.

1. Unplug the power
2. Loosen the plastic end cap (I) on the end of the first strand and plug in the new set of lights.
3. Fasten the gasket to secure the connection.
4. Install each strand following the installation instructions.
5. Plug in the power supply. When plugged back in, the power supply will register the newly linked strands.

ADDING 10FT. EXTENSION CABLE

Connect anywhere along the strand, between linked strands or to extend the power supply cord. Ensure the lights are unplugged before proceeding. The total combined length of strands and extensions cannot exceed 200ft. (60.9m). Ensure the safety cap is covering any unused end of the cord.

TRIMMING THE END OF THE STRAND

The very last light strand in a series of strands may be cut to remove unwanted LED pucks.
WARNING: Completely unplug the power supply before proceeding. DO NOT remove more than eight LED pucks from a strand. A minimum of four must remain for the power supply to register the lights. Strands cannot be cut, then reconnected. Cutting a strand will reduce the ingress protection (IP) rating of the product. DO NOT put cut strandsin a location where water may accumulate.

1. Unplug the power
2. Using wire cutters, cut the light strand in a straight line leaving at least of cord for easy installation of the silicone end cap (J).
3. Firmly push the silicone end cap over the cut cord until it is firmly in To ensure the best water seal, apply a small amount of silicone caulk sealant in the end cap before installation.
4. Plug in the power
5. In the Enbrighten app, manually disable the removed LED pucks following the available instructions and resources.

MANUAL CONTROL

Press the pairing button on the power supply to manually cycle through the following modes

FCC/IC

Suppliers Declaration of Conformity | Model #: 81102, 82729 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving
• Consult the dealer or an experienced radio/TV technician for

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

CAN ICES-3(B)/NMB-3(B)

WARRANTY INFORMATION

IMPORTANT — PLEASE READ
Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.
This Jasco product has a limited-lifetime replacement warranty. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1), M-F, 7AM-8PM Central Time or www.byjasco.com if the unit should prove defective within the warranty period.

WARNINGS

WARNING: When using outdoor portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury, including the following:
Ground fault circuit interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are available having built-in GFCI protection and can be used for this measure of safety.
Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW
WARNING: When using outdoor portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury, including the following:

1. Ground fault circuit interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are available having built-in GFCI protection and can be used for this measure of safety.

Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW

RISK OF FIRE

• ETERNTIY LIGHTS ARE DESIGNED TO BE LINKED BY USING THEIR ELECTRICAL PLUGS AND RECEPTACLES TO A MAXIMUM OF
• EAVE LIGHT INTERCONNECTING RECEPTACLES ARE INTENDED ONLY FOR THE LINKING OF COMPATIBLE EAVE LIGHT DO NOT USE EAVE LIGHT RECEPTACLES FOR ANY OTHER ELECTRICAL PURPOSE.

NOT INTENDED FOR INSTALLATION OF POWER SUPPLY, LED PUCK, OR CORDS IN CEILINGS IN CEILINGS, SOFFITS, CABINETS, ATTICS OR OTHER ENCLOSED SPACES

MADE IN THAILAND

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
©JASCO 2024 | 81102, 82729 | 01/26/24 v1
App Store is a service mark of Apple Inc.
Google, Google Play and Google Home are trademarks of Google LLC.
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its a liates

Read More About This Manual & Download PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>