Sky Microwave SKY-FFV580P02A Microwave Doppler Sensor Module User Manual

SKY-FFV580P02A Microwave Doppler Sensor Module

SKY MICROWAVE
Microwave Doppler Sensor Module
SKY-FFV580P02A

L19mm W20mm H7mm
Module Size
19(mm)

7(mm)

20(mm)

1(mm)
VVC GND OUT

VVC GND OUT

2(mm)

9.5(mm)

PIN definition

OUT GND DC5-12V

WWW.SKYMICROWAVE.COM
Add: Room 528, Suite A, Liwan Building, #0101Qianhai Road, Nanshan District, Shenzhen, 518054, Guangdong China. +86 755 86051735 Fax:+86 755 26483339 Email: sales@skymicrowave.com

SKY MICROWAVE CO., LTD

Technical Perimeters

Basic perimeters Input Operating current Frequency Frequency stability
Output power Harmonic Filtering and amplifier Amplifier Low pass frequency Reference TTL Maximum Maximum
Operating Environment Operating temperature Storage Relative humidity

DC 5-12V 16mA±2mA (DC 5V) 5.8GHz±75MHz ±10 MHz max. (-30 to +80°C) -3dBm±2dB FCC15.249
45000 2-37Hz 2.0V 0V 3.6V
-30°C 80°C -40°C 80°C 95 % at 35

WWW.SKYMICROWAVE.COM
Add: Room 528, Suite A, Liwan Building, #0101Qianhai Road, Nanshan District, Shenzhen, 518054, Guangdong China. +86 755 86051735 Fax:+86 755 26483339 Email: sales@skymicrowave.com

SKY MICROWAVE CO., LTD

Sensing area
Ceiling installationAngle 360°H 2.5-3mSensing radius 5-6m

0°

330°

30°

300°

60°

270° 11 10 8 6 4 2

2 4 6 8 10 11 90°

240°

Top view

210°

180°

120°
150°
Unit(m)

Wall mountedAngle 130° H 0.8-2mFront sensing range<15m

90° 18 16 14 12 10 8 6 4 2

2 4 6 8 10 12 14 16 18 90°

60°
30°
Side view

60°

30°

0°

Unit(m)

Note: Above test results are based on our filtering and amplifier circuitry.

WWW.SKYMICROWAVE.COM
Add: Room 528, Suite A, Liwan Building, #0101Qianhai Road, Nanshan District, Shenzhen, 518054, Guangdong China. +86 755 86051735 Fax:+86 755 26483339 Email: sales@skymicrowave.com

FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi s device may not cause harmful interference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte rference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling The final end product must be labeled in a visible area with the following” Contains FCC ID: 2ADDD-FFV580P02A”
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules

CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions

This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
2.4 Limited module procedures
Not applicable
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

2.7 Antennas

This radio transmitter 2ADDD-FFV580P02A has been approved by Federal Communications Commission to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Peak gain ( dBi )

Model

Type Connector 2400-2483.5 5150-5250 5250-5350 5470-5725 5725-5850

MHz

MHz

MHz

MHz

MHz

5.8G

int ernal

/

/

ant enna

/

/

/

1.85dBi

2.8 Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID:2ADDD-FFV580P02A.
2.9 Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.

ISED Statement

–

English: This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, a

nd (2) This device must accept any interference, including interference that may cause undesired

operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

– French: Le présentappareilestconforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitationestautorisée aux deux conditions suivantes: (1) l’appareil

ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareildoit accepter tout brouillageradi

oélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le fonctionnement.

l’appareil numérique du ciem conforme canadien peut – 3 (b) / nmb – 3 (b).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

cet appareil est conforme à l’exemption des limites d’évaluation courante dans la section 2.5 du cnr – 102 et conformité avec rss 102 de l’exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l’exposition aux champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme Canada limites d’exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
ISED Modular Usage Statement NOTE 1: When the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use the wording “Contains transmitter module IC: 21036-58GHZMOTION” or “Contains IC: 21036-58GHZMOTION”.

NOTE 1: Lorsque le numéro de certification ISED n’est pas visible lorsque le module est installé dans un autre appareil, l’extérieur de l’appareil dans lequel le module est installé doit également afficher une étiquette faisant référence au module inclus. Cette étiquette extérieure peut être libellée Contient le module émetteur IC:21036-58GHZMOTION ou Contient IC: 21036-58GHZMOTION.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>