PUR P2QC8506BLS Bottleless Point-of-Use Water Dispenser Dual Stage Filtration System Owner’s Manual

PUR P2QC8506BLS Bottleless Point-of-Use Water Dispenser Dual Stage

Filtration System Owner’s Manual

Includes Quick-Connect Filter

Safety Precautions:

• IMPORTANT: Refrigerants must be handled and disposed of by qualified service personnel only. Before discarding this water dispenser to landfill, contact local authorities for advice on proper disposal methods for refrigerants.
• This Water Dispenser is designed for “indoor” use only. DO NOT USE OUTDOORS.
• Never turn the dispenser upside down or tilt more than 45 degrees. During transportation, if the dispenser was transported sideways, the unit must be left to stand upright for 12 hours before connecting to power source and initiating operation.
• This Water Dispenser is equipped with a grounded power cord and plug for your safety.
• Keep your Water Dispenser in a dry place away from any heat source and direct sunlight.
• Never put anything flammable close to the dispenser.
• Leave a minimum of 2” (5cm) around the back and sides of the dispenser for proper ventilation.
• Always install your Water Dispenser on a level, solid floor.
• Wait 3 minutes before restarting dispenser after shutting it down.
• Always unplug (disconnect) the Water Dispenser power cord before servicing, cleaning and filter replacement.
• Service must be performed by qualified/authorized service personnel only. Service information is available through our Customer Service Department at 1-877-447-4768 or e-mail customerservice@ghpgroupinc.com.
• Regular cleaning of your Water Dispenser is required for your warranty.
• Please follow the cleaning and maintenance instructions outlined in this manual. Cleaning should be done every 4 ~ 6 months.
• It is your responsibility to ensure that all water line connections are properly connected and sealed and there are no system water leaks before operating the unit.
• Although this unit incorporates provision of a hot water “child resistant safety switch,” never allow children to dispense hot water without proper and direct supervision.
• Only use original PUR filters with this unit. (Part # PQCSED and PQCCRBL).

DANGER: The hot water in this dispenser is heated to approximately 90°C (194°F). Temperatures above 52°C (125°F) can cause severe burns from scalding.

Pre-Operation:

Grounding Precautions:

WARNING: Failure to follow these instructions can result in death, fire or electrical shock.

• This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for electric current.
• Improper use of the grounding plug can result in a risk of property damage, electric shock causing serious injury and even death.
• This appliance is equipped with a power cord having a grounding wire with a grounding plug and must be connected into a properly grounded polarized outlet. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the wall outlet is properly grounded.
• If the wall outlet is a standard 2 prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
• Do not under any circumstances cut or remove the third (ground) pin from the power cord plug.
• Do not use adapter plugs or extension cords with this appliance.
• If the power cord is too short, have a qualified electrician install an electrical outlet near the appliance.
• Do not use the appliance if the power cord becomes frayed or otherwise damaged.
• A 115 Volt, 60 Hz., AC only 15 amperes fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your Water Dispenser be provided. Use an outlet that cannot be turned off by a switch.

Specifications:

Water Dispenser Layout and Components:

Installation Instructions:

WARNING: It is highly recommended to have your Water Dispenser installed by a licensed plumber. If you are installing the Water Dispenser yourself, the following information is important: It is your personal responsibility to adhere to all Governing State, Federal, Provincial and Local Plumbing Code Regulations.

Depending on the type of plumbing in your home (copper or flexible pipe), the following plumbing installation accessories (not included with the Water Dispenser) will be required to complete the installation of your Water Dispenser. These items can be purchased at your local hardware store.

Installation Location:

Select a suitable location where the Water Dispenser will be installed, making sure you have easy access to an electrical wall outlet and the household cold water supply line.

Water Line Hook-Up:

1. IMPORTANT: Turn off the household cold water supply line.
2. Open the cold water faucet allowing water to purge the system to minimize water leakage cleanup.
3. COPPER PIPE PLUMBING : Using a tube/pipe cutter, cut and remove a section of the cold water line at the desired height. Cut should be made above any manual shut-off valve installed on the water line.
4. Using an emery cloth, clean the ends of the copper pipes and apply a liberal layer of flux to both the inside of the fitting and the outside of the pipe before sliding the two parts together that are being soldered. Follow manufacturer’s installation instructions provided with the 1/2” Male Solder x 1/4” OD Compression Fitting Shut-Off Valve (B).
5. FLEXIBLE PIPE PLUMBING: Using a tube/pipe cutter, cut and remove a section of the cold water line at the desired height. Cut should be made above any manual shut-off valve installed on the water line. Follow manufacturer’s installation instructions provided with the 1/2” x 1/2” x 1/2” Quick-Grip Tee (D) and 1/2” Quick-Grip x 1/4” OD Compression Fitting Shut-Off Valve (E).
6. Close the newly installed Shut-Off Valve (Figure 1A and Figure 1B) and slowly re-open the cold water supply line and check for leaks. If leaks are detected, immediately turn off the water supply and repair any leaks. If no leaks are detected, proceed to step 7.
7. The Water Dispenser includes 1.8 meters (6 feet) of 1/4” OD Flexible Tubing. If additional
   Tubing is needed, it can be purchased at your local hardware store. Cut the desired length to suit your installation requirements, making sure both ends of the Tubing are cut straight/ square (Figure 1 & Figure 2). Remove the Compression Nut and Ferrule from the Valve and install them onto the Tubing (Figure 3). Insert the Tubing into the Valve until it stops (Figure 4). Slide both the Compression Nut and Ferrule toward the Valve and tighten the Compression Nut firmly using a wrench (Figure 5). DO NOT OVERTIGHTEN.

8. The Water Dispenser is equipped with a Manual Shut-Off Valve installed on the rear of the unit (Figure 6) for easy access in case of an emergency. Remove sanitation plug from the Shut-Off valve before installing the water line (Figure 7).
9. Connect the incoming water line into the open side of the Manual Shut-Off Valve (Figure 6). This valve utilizes Quick-Connect Fittings, for which no tools are required. Simply insert the end of the Tubing firmly into the Manual Shut-Off Valve until it comes to a complete stop (approx. 1/4”) (Figure 8).

WARNING: DO NOT OPEN THE COLD WATER SUPPLY VALVE AT THIS STAGE. (See Installation of Filter)
To disconnect the Tubing from the Manual Shut-Off Valve, you must first remove the Blue “Horseshoe C-Clip” from the Quick-Connect Fitting (Figure 9). Then push in the Collet and pull out the Tubing to remove it from the Manual Shut- Off Valve (Figure 7).

NOTE: The Blue”Horseshoe C-Clip” must always be installed PRIOR to installation of the water lines.

Filter Installation (See Figure 10 & 11):

The Filters inside the Water Dispenser have not been factory installed. They have been shipped in their original shrink-wrapped packaging for sanitation purposes.

The Filters are located behind the Lower Front Panel of the Dispenser. Follow these steps to access/install the Filters:

1. Remove the Magnetized Lower Front Panel from the Dispenser (Figure 10).
2. Remove the Filters from the Retaining Clip, and remove the shrink-wrap.
3. Check that the Red Locking Tabs, (Filter Heads) are positioned to the left “Unlock” position (Figure 11).
4. Insert the Sediment Filter into the Sediment Filter Head (left side), and give it a 1/4 turn clockwise until it stops and the dots are properly aligned. Repeat the same process for the Carbon Block Filter (right side). Push the Red Locking Tab to the right “Locked” position (See Fig. 11) for both filters. If the Red Locking Tab fails to engage (lock), the Filter may not be properly aligned. Make sure the color dots on the filter head and filter are properly aligned.

NOTE: The internal water connection lines to the Filter Head are factory installed.

The installation is now complete. Slowly open the Shut-Off Valve. Check all connections for leaks prior to opening all water valves fully. If any leaks are detected, immediately turn off the water supply and repair.

Water Leakage Detection System:

This Water Dispenser is equipped with a low voltage water leakage detection system located inside the base of the filter compartment and is covered by a removable drip tray (Figure 12a). In the event any water makes contact with the leakage detection system, an audible alarm will sound continuously until the water is removed. Upon activation of the leakage detection system, the water inlet solenoid valve (located internally) is automatically deactivated suspending incoming water activity until the alarm is silenced. To silence the alarm, all accumulated water surrounding the sensors (Figure 12b), must be removed using a sponge and/or paper towels. The water inlet solenoid valve reactivates automatically once the alarm is silenced.

Filter Replacement:

For optimum water efficiency and performance, we recommend replacing the filter every 6 months. Replacement filters can be ordered on-line at: www.ghpgroupinc.com. Use only original PUR filters with this unit. (Part # PQCSED and PQCCRBL)

CAUTION: Before replacing the filters, always turn off the water supply using the manual shut-off valve located at the rear of the dispenser. This will depressurize the water line and minimize water over spray when the filter is released. Remove and empty drip tray of any accumulated water found under the filter. If the audible alarm sounds, refer to “WATER LEAKAGE DETECTION SYSTEM” instructions.

Initial Product Cleaning:

Like most appliances, your Water Dispenser requires periodic maintenance for maximum efficiency and performance. It must be cleaned on a regular basis, (coincide with filter replacement i.e. every 6 months) in order to maintain a hygienic environment and prevent potential bacteria growth.

1. Always disconnect (unplug) the power cord before attempting any cleaning, maintenance and filter replacement.

2. Before attempting any cleaning, maintenance and/or filter replacement, always turn off the water supply using the manual shut-off valve at the rear of the dispenser.

3. To access the reservoir system, you must remove the top cover on the dispenser by removing the two Phillips screws located at the rear of the cover (Figure 13).

4. Carefully lift off the top cover. This may require using a little force.

5. Remove the reservoir cover by carefully pulling upward (Figure 14).

6. Fill the reservoir with a pre-mixed solution of 15ml (1 tbsp) white vinegar with 3.0L (0.79 gal) of hot water and let stand for 20 min (Figure 15).

7. Place a jug under the dispensing spigot and press both hot and cold dispensing buttons until the cleaning solution stops flowing (Figure 16).

8. Flush the reservoir with clean water and press both dispensing buttons until water stops flowing.

9. To drain any remaining water from the reservoirs, unscrew the drain cap and plug located at the rear of the dispenser (Figure 17). Collect the water into a bucket. Flush the reservoir a second time with clean water.
   IMPORTANT: Remember to re-install and tighten the drain cap and the plug.

10. Re-install the reservoir cover by pressing down firmly.

11. Re-install the dispenser top cover and secure using the two Phillips screws.

12. Re-connect the power cord.

13. Re-open the manual shut-off valve. You will hear water entering the system which will stop automatically when the appropriate water levels are reached.

14. Place a container under the water dispensing spigot and press both dispensing buttons (separately) to make sure water is flowing normally.

Operation Instructions:

IMPORTANT NOTE: Your PUR® Water Dispenser is designed with a special safety feature (float switch mechanism) that controls the operation of the hot water tank heating system.

If no water is present and/or low water levels are detected inside the internal reservoir system, operation of the hot water heating system is not possible. Likewise, if the hot water heating is operational and water is being drawn simultaneously causing water levels to drop below safe levels, hot water tank operation is automatically terminated until normal water levels are restored.

NOTE: Operation of the cold water system is not affected by this safety feature.

Dispensing Hot Water (See Figure 18 & 19):

CAUTION: Do not allow children to use the hot water dispensing button without proper and direct supervision.

To prevent hot water from being dispensed accidentally and possibly harming a child, the hot water dispensing button can only be operated when the child resistant safety switch is activated. To dispense hot water, push in the child resistant safety switch (Figure 18), then press/hold the hot water button (Figure 19). Upon releasing the hot water button, the child safety switch automatically re-engages to the locked position.

WARNING: The hot water is heated to approximately 90°C (194°F).
Temperatures above 52°C (125°F) can cause severe burns from scalding.

NOTE: The hot water temperature (factory default setting) is not adjustable on this unit.

Dispensing Cold Water:

The cooling system on this unit is designed to activate automatically as soon as the power cord is connected.

1. When the blue LED light is “flashing” the cooling cycle is operational. When the blue LED is light is “on” the cooling cycle (compressor) is off and the cold water has reached optimum temperature.
2. To dispense cold water, place cup/glass under dispensing spigot, push/hold the cold water dispensing button until the desired amount of water is dispensed.

NOTE: This Water Dispenser left the factory with the cold water temperature control default setting positioned for Energy Star compliance (Figure 20). This setting will deliver cold water temperatures between 8°C – 10°C (46°F – 50°F).

Adjusting the Cold Water Temperature (See Figure 20):

The temperature of the cold water reservoir is monitored by a cold water control located at the rear of the dispenser. By turning the thermostat set screw (Figure 20) the temperature can be adjusted. Using a screwdriver, turn the dial clockwise between “L” (lower setting for warmer water) and “H” (higher setting for colder water) until the desired temperature is reached. If water is not being properly dispensed, there could be possible ice build-up in the reservoir due to the thermostat being set too cold.

If this happens, slowly rotate the thermostat set screw counter-clockwise to a warmer setting.

NOTE: Any change to the cold water temperature control may effect Energy Star efficiency.

Cleaning and Maintenance:

Cleaning the Drip Tray (See Figure 21) :

NOTE: The drip tray is NOT dishwasher safe.
To remove, pull the drip tray towards you. Drain and clean. The drip tray should be emptied and cleaned regularly to remove spotting and mineral deposits.

Clean with a mild soap and water mixture. For tough deposits, add vinegar and let soak until the deposits come loose. Then wash, rinse and dry thoroughly. Put the grill back on the tray and install on the dispenser.

Cleaning the Outside of the Water Dispenser:

The outside of the dispenser can be wiped clean using a mild soap and water mixture. Never use harsh chemicals or abrasive cleaners. Rinse thoroughly with clean water and then dry surfaces.

Vacuum or sweep away the dust from the condenser coils (Figure 22) at the back of the dispenser. Keeping the condenser coils clean improves cooling efficiency.

Internal Reservoir Overflow Protection:

The internal (cold tank) reservoir incorporates a water overflow flotation device (Figure 23). The operating parameter of this device allows the float to move freely “up/down” according to related water levels. As water levels rise, so does the float causing the water inlet valve to close at a pre-determined level. As water levels fall, so does the float causing the water inlet valve to open allowing replenishment of incoming water.

Draining the Reservoirs:

IMPORTANT! Unplug the dispenser before performing this procedure.
Dispense hot water until temperature drops to a safe level to avoid the risk of scalding.

1. Turn off the water supply, using manual shut-off valve at the rear of the dispenser.
2. Press both dispensing buttons until water stops flowing (Figure 24).
3. Place a bucket beneath the drain valve located at the rear of the dispenser (Figure 25).
4. Remove the drain cap and plug from the drain valve and let the remaining water flow into the bucket.
5. Replace the cap and plug.

Going Away on Vacation:

When not using the dispenser for long periods of time or when going on vacation, unplug the dispenser and drain the reservoirs (See Draining the Reservoirs above). Follow Initial Product Cleaning Procedures upon return.

Performance Data Sheet:

Note: Read this performance data and compare the capability of this system with your actual water treatment needs. It is recommended that, before installing the system, you have your water supply tested to determine your actual water treatment needs.

This system conforms to NSF/ANSI 42 and 53 for the specific performance claims as verified and substantiated by test data. While testing was performed under standard laboratory conditions, actual performance may vary.

The PQC2FS system has been certified by NSF International according to NSF/ANSI 42, 53 and CSA B483.1 for the reduction of substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF/ANSI 42 and 53.

PQC2FS with PQCSED and PQCCRBL Filters

Flow Rate = 0.5 gpm (1.9 lpm) Capacity = 500 gallons (1,890 L) or 6 months

Tested by NSF International according to NSF/ANSI Standard 42, 53 and CSA B483.1.

Troubleshooting Guide:

Attention: Do not return this product to the store.
Should service be required or you have any questions regarding how to use your PUR product, please contact Customer Service at:
1-877-447-4768 or customerservice@ghpgroupinc.com

Manufactured and warranted by GHP Group Inc.
USA: 6440 W. Howard St. Niles, IL 60714-3302
Canada: 271 Massey Rd. Guelph, Ontario, N1K 1B2

Warranty:

Limited Warranty:
This limited warranty is extended to the original retail purchaser of this water dispenser and warrants against any defect in material and workmanship for a period of one (1) year from the date of retail sale. GHP Group, Inc., at its option, will either provide replacement parts or replace the unit, when properly returned to the retailer where purchased within one (1) year of retail purchase. (Shipping costs, labor costs, etc. are the responsibility of the purchaser.)

Duties of the Owner:
This water dispenser must be installed and operated in accordance with the written instructions furnished with this unit. This warranty shall not excuse the owner from properly maintaining this unit in accordance with the instructions. A bill of sale, canceled check or payment record must be kept to verify purchase date and establish warranty period. Original carton should be kept in case of warranty return of the unit.

What is Not Covered?

• Service trips to your home to teach you how to use the product.
• Improper installation, delivery, or maintenance. Failure to maintain the product according to the instructions outlined in the product manual will automatically void the warranty.
• Failure of the product if it is abused, misused, altered, used commercially, or used for other than the intended purpose.
• Products that are used outside a residential or office environment.
• Replacement of house fuses or resetting of circuit breakers.
• Use of this product where water is microbiologically unsafe or of unknown quality.
• Damage to the product if used to dispense anything other than water.
• Damage to the product caused by accident, fire, floods, or acts of God.
• Any service to the product by unauthorized personnel.
• Incidental or consequential damage caused by possible defects with this appliance, its installation or repair.

THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. THE REMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES. IN NO EVENT WILL GHP GROUP. INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

Claims Handled as Follows:

1. Contact your retailer and explain the problem.
2. If the retailer is unable to resolve the problem, contact our Customer Service Dept. detailing the system model, the problem, and proof of date of purchase.
3. A representative will contact you. DO NOT RETURN THE UNIT TO GHP GROUP, INC. unless instructed by our Representative, or with written authorization.

This warranty gives you specific legal rights and you may also have other rights that vary from state/province to state/province.

Product Registration:
To register your product, please visit: ghpgroupinc.com/product- registration.html and complete within (14) days of purchase.

Read More About This Manual & Download PDF:

References

• GHP Group Inc Product Registration
• GHP Group Inc
• p65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>