SportDOG SportTrainer SD-1275E Remote Trainer User Guide

: June 6, 2024
: sportDOG

SportDOG SportTrainer SD-1275E Remote Trainer

Product Image

The SportDOG® SportTrainer® SD-1275E Remote Trainer has been proven safe, comfortable, and eﬀective for all dogs over 3.6 kg. Consistent, correct use of this product allows you to reinforce commands and correct misbehavior from up to 1200 m. The Remote Transmitter sends a signal, activating the Collar Receiver to deliver harmless stimulation. With proper training, a dog will learn to associate this signal with a command. Like all SportDOG® products, this model features adjustable static stimulation levels so you can tailor the stimulation level to your dog’s temperament, eliminating the risk of over- stimulation.
IMPORTANT: The SportTrainer® SD-1275E Remote Trainer has a range of 1200 m. Depending on the way you hold the Remote Transmitter, the maximum range may vary. For consistent results at longer ranges, hold the Remote Transmitter in a vertical position away from your body and above your head. Terrain, weather, vegetation, transmissions from other radio devices, and other factors will aﬀect the maximum range.

THE SPORTTRAINER® SD-1275E CONTAINS

Remote Transmitter
Collar Receiver
Charging Cradle
Wall Charger
Lanyard
Long Contact Points
Test Light Tool

STEP:01

CHARGING THE BATTERIES

FIRST THINGS FIRST, the SportTrainer® SD-1275E Remote Trainer needs its batteries charged before you can use it. While your system is charging, read the entire Operating Guide available online at www.sportdog.com become familiar with your system.

TO CHARGE THE REMOTE TRANSMITTER

Align Contact Points with the Charging Cradle.
Push Charging Cradle onto Remote Transmitter until it snaps into place.
Plug the charger into a standard wall outlet.
Charge the Remote Transmitter for 2 hours. It is not harmful to let the unit charge more than 2 hours.
When charging is complete, as indicated by the full battery icon, remove Charging Cradle.

TO CHARGE THE COLLAR RECEIVER

Align the Contact Points with the Charging Cradle making sure the hole on the Charging Cradle aligns with the Receiver Indicator Light.
Push the Charging Cradle up and back on the Collar Receiver until the Cradle snaps into place.
Plug the Charger Connector into the Charging Cradle.
Plug the charger into a standard wall outlet.
Charge the Collar Receiver for 2 hours. It is not harmful to let the unit charge more than 2 hours.
When charging is complete, as indicated by the Indicator Light blinking green, remove the Charging Cradle from the Collar Receiver.

NOTE: Approximate battery life between charges for both the Remote Transmitter and Collar Receiver is 140 to 160 hours, depending on the frequency of use.

STEP:02

TURNING THE SPORTTRAINER® SD-1275E COMPONENTS ON AND OFF

Once charged, the Remote Transmitter is on. Press any button to send signals.

TO TURN THE COLLAR RECEIVER ON

Press and release the On/Oﬀ Button. The Receiver Indicator Light will come on solid green and the Collar Receiver will beep 1 to 3 times indicating which static stimulation range is set. The default is 2 (medium).

TO TURN THE COLLAR RECEIVER OFF

Press and release the On/Oﬀ Button. The Receiver Indicator Light will come on solid red and the Collar Receiver will beep for 2 seconds. To extend the battery life between charging cycles, turn oﬀ the Collar Receiver when it is not in use.

STEP:03

PROGRAM THE REMOTE TRANSMITTER

The SportTrainer® SD-1275E Remote Trainer has 12 operational modes to best match your style of training. See STEP 05 of your Operating Guide for complete descriptions of the available modes.
NOTE: The Remote Transmitter is factory set to mode 1.

TO CHANGE THE MODE:

Refer to the following table to review the available modes.
Using the Intensity Buttons +/-, set the display to 1.
Turn the Remote Transmitter over and remove the belt clip (if attached).
Using a pen or the tine of a buckle, depress and release the Mode Button. Select the desired mode using the Intensity Buttons +/-. After 5 seconds, your selected mode will ﬂash to indicate that it has been set. Your remote transmitter will now return to the same Intensity level and dog to which it was previously set.

For multi-dog dog operation, refer to STEP 07 in the Operating Guide.

MODE

|

Left Button

|

Top Right Button

|

Bottom Right Button

---|---|---|---

1

| Tone Only|

Continuous*

|

Momentary*

2

| Vibration Only|

Continuous*

|

Momentary*

3

| Continuous*|

Tone Only

|

Vibration Only

4

| Momentary*|

Tone Only

|

Vibration Only

5

| Locate Remote Beeper***|

Continuous*

|

Tone Only

6

| Locate Remote Beeper***|

Continuous*

|

Vibration Only

7

| Tone Only|

Continuous*

|

+2 Boost**

8

| Vibration Only|

Continuous*

|

+2 Boost**

9

| Rising|

Continuous*

|

Tone Only

10

| Rising|

Continuous*

|

Vibration Only

11

| Remote Launcher***|

Continuous*

|

Tone Only

12

| Remote Launcher***|

Continuous*

|

Vibration Only

Static stimulation level adjusted by Intensity Button.
** The +2 Boost sends a signal to the collar to issue a static stimulation that is 2 levels higher than the currently selected level. The system will not correct higher than level 10.
*** See your Operating Guide for more information

STEP:04

MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER

The Remote Transmitter has been pre-conﬁgured to work with the Collar Receiver. However, if you are using multiple Collar Receivers you will need to match the Collar Receivers to the Remote Transmitter.

TO MATCH THE COLLAR RECEIVER TO THE REMOTE TRANSMITTER

Turn the Collar Receiver oﬀ.
Press and hold the On/Oﬀ Button. The Receiver Indicator Light will come on and then turn oﬀ after 5 seconds. NOTE: If the Receiver Indicator Light begins flashing, repeat this step.
Release the On/Oﬀ Button.
Press and hold one of the Side Buttons on the Remote Transmitter until the Receiver Indicator Light ﬂashes 5 times.
Once the Receiver Indicator Light has ﬂashed 5 times, the Collar Receiver has been reset and will begin ﬂashing as normal. If the Receiver Indicator Light does not ﬂash, repeat this procedure.

STEP:05

PROGRAM THE SYSTEM FOR MULTI-DOG OPERATION

SportDOG® Add-A-Dog™ extra Collar Receiver(s) must be purchased to train additional dogs. Every operational mode can be used with multiple dogs.

CHANGE THE MODE

Set display to 2 for multi-dog mode (see STEP 03). Select the number of dogs using the Dog Buttons +/-. After 5 seconds, the Remote Transmitter will ﬂash 3 times to conﬁrm your selection.

Program the ﬁrst Collar Receiver.
Turn the Collar Receiver oﬀ.
Press and hold the On/Oﬀ Button. The Receiver Indicator Light will come on, then turn oﬀ after 4-5 seconds. If the On/Oﬀ Button is released too early, the Receiver Indicator Light will begin its normal ﬂashing. If this occurs, start over from A.
After the Receiver Indicator Light has turned oﬀ, release the On/Oﬀ Button.
Press and hold one of the Side Buttons on the Remote Transmitter until the Receiver Indicator Light ﬂashes 5 times. If the Receiver Indicator Light does not ﬂash 5 times, start over from A.
To match additional collars, use the Dog Buttons +/- for Dog 2, etc. and follow the steps listed above.

STEP:06

FIT THE COLLAR RECEIVER

CAUTION: Please see page 3 of the SportTrainer® SD-1275E Operating Guide for Important Safety Information.

Put the Collar Receiver around your dog’s neck and adjust to ﬁnd the proper ﬁt. Fasten the Collar Receiver so the ﬁt is snug yet loose enough to allow one ﬁnger to ﬁt between the strap and the dog’s neck. Fit is important because a loose collar may cause inconsistent performance.

TERMS OF USE AND LIMITATION OF LIABILITY

Terms of Use
Use of this Product is subject to your acceptance without modiﬁcation of the terms, conditions and notices contained herein. Use of this Product implies acceptance of all such terms, conditions and notices. If you do not wish to accept these terms, conditions, and notices, please return the Product, unused, in its original packaging and at your own cost and risk to the relevant Customer Care Centre together with proof of purchase for a full refund.
Proper Use
This Product is designed for use with dogs where training is desired. The speciﬁc temperament or size/weight of your dog may not be suitable for this Product. Radio Systems Corporation recommends that this Product is not used if your dog is aggressive and accepts no liability for determining suitability in individual cases. If you are unsure whether this Product is appropriate for your dog, please consult your veterinarian or certiﬁed trainer prior to use. Proper use includes, without limitation, reviewing the entire Operating Guide and any speciﬁc safety information.
No Unlawful or Prohibited Use
This Product is designed for use with dogs only. This dog training device is not intended to harm, injure
or provoke. Using this Product in a way that is not intended could result in violation of Federal, State
or local laws.
Limitation of Liability
In no event shall Radio Systems Corporation or any of its associated companies be liable for (i) any indirect, punitive, incidental, special or consequential damage and/or (ii) any loss or damages whatsoever arising out of or connected with the misuse of this Product. The Purchaser assumes all risks and liability from the use of this Product to the fullest extent permissible by law.
Modification of Terms and Conditions
Radio Systems Corporation reserves the right to change the terms, conditions and notices governing this Product from time to time. If such changes have been notiﬁed to you prior to your use of this Product, they shall be binding on you as if incorporated herein.

COMPLIANCE

This equipment has been tested and found to comply with relevant RED Directives. Before using this equipment outside the EU countries, check with the relevant local RED authority. Unauthorized changes or modiﬁcations to the equipment that are not approved by Radio Systems Corporation are in violation of EU RED regulations, could void the user’s authority to operate the equipment, and void the warranty.
The Declaration of Conformity can be found at: www.sportdog.com/eu_docs.php.
IC – SD-1275E/SDT54-16042
This device complies with Industry Canada licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter, model number SDT54-16042, has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Monopole antenna, part number 610-2395 or equivalent , with -27 dbi gain.
ACMA
This device complies with the applicable EMC requirements specified by the ACMA (Australian Communications and Media Authority).

BATTERY DISPOSAL

WARNING: Please see page 3 of the SportTrainer® SD-1275E Operating Guide for Important Safety Information related to the batteries.

This system operates on two Li-Ion battery packs (420 mAh capacity for the Collar Receiver, 500 mAh capacity for the Remote Transmitter). Only replace with battery received from calling the Customer Care Centre. For a listing of the telephone numbers in your area, visit our website at www.sportdog.com.
Separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. Please see below for instructions on how to remove the battery from the product for separate disposal.
AT END OF PRODUCT LIFE, USE THESE BATTERY REMOVAL INSTRUCTIONS FOR FINAL DISPOSAL (DO NOT OPEN THE COLLAR RECEIVER OR REMOTE TRANSMITTER UNTIL YOU HAVE RECEIVED THE REPLACEMENT).

Using a T8 Torx screwdriver, remove the case screws from your Remote Transmitter.
Using a 3/32 Allen Wrench, remove the case screws from your Collar Receiver.
Remove the case back or cover.
Remove the old battery pack.

WARNING

When removing the old battery pack, care must be taken when gripping the connector ﬁrmly to avoid damaging the wires. Shorting the battery wires may cause ﬁre or explosion.
These instructions are not valid for repair or battery replacement. Replacing the battery with a battery not speciﬁcally approved by Radio Systems Corporation may cause ﬁre or explosion. Please call the Customer Care Centre to avoid invalidating your warranty.

IMPORTANT RECYCLING ADVICE
Please respect the Waste Electrical and Electronic Equipment regulations in your country. This equipment must be recycled. If you no longer require this equipment, do not place it in the normal municipal waste system. Please return it to where it was purchased in order that it can be placed in our recycling system. If this is not possible, please contact the Customer Care Centre for further information. For a listing of Customer Care Centre telephone numbers, visit our website at www.sportdog.com.

WARRANTY

THREE YEAR NON-TRANSFERABLE LIMITED WARRANTY
This Product has the beneﬁt of a limited manufacturer’s warranty. Complete details of the warranty applicable to this Product and its terms can be found at www.sportdog.com and/ or are available by contacting your local Customer Care Centre.
Europe – Radio Systems PetSafe Europe Ltd, 2nd Floor, Elgee Building, Market Square Dundalk, Co. Louth, A91 YR9X Ireland
Canada – Radio Systems Corporation, 10427 PetSafe Way, Knoxville, TN 37932 USA
Australia/New Zealand – In compliance with the Australian Consumer Law, Warranties Against Defects, eﬀective January 1, 2012, warranty details of this Product are as follows: Radio Systems Australia Pty Ltd. (hereinafter referred to as “Radio Systems”) warrants to the original retail purchaser, and not any other purchaser or subsequent owner, that its Product, when subject to normal and proper residential use, will be free from defects in material or workmanship for a period of three (3) years from the purchase date. An “original retail consumer purchaser” is a person or entity who originally purchases the Product, or a gift recipient of a new Product that is unopened and in its original packaging. When serviced by Radio Systems Customer Service, Radio Systems covers labour and parts for the ﬁrst three years of ownership; after the ﬁrst three years, a service or upgrade charge will apply relative to replacement of the Product with new or refurbished items at Radio Systems’ sole discretion.
The limited warranty is non-transferable and shall automatically terminate if the original retail consumer purchaser resells the Radio Systems Product or transfers the property on which the Radio Systems Product is installed. This Limited Warranty excludes accidental damage due to dog chews; lightning damage; or neglect, alteration, and misuse. Consumers who purchase products outside of Australia, New Zealand, or from an unauthorized dealer will need to return the Product to the original place of purchase for any warranty issues.
Pease note that Radio Systems does not provide refunds, replacements, or upgrades for change of mind, or for any other reason outside of these Warranty terms.

Claims Procedure: Any claim made under this Warranty should be made directly to Radio Systems Australia Pty Ltd. Customer Care Centre at:
Radio Systems Australia Pty Ltd.
PO Box 7266, Gold Coast Mail Centre QLD 9726, Australia
Australia Residents: 1800 786 608
New Zealand Residents: 0800 543 054
Email: aus-info@petsafe.net
To ﬁle a claim, a proof of purchase must be provided. Without a proof of purchase, Radio Systems will not repair or replace faulty components. Radio Systems requests the Consumer to contact the Radio Systems Customer Care Centre to obtain a Warranty Return number, prior to sending the Product. Failure to do so may delay in the repair or replacement of the Product.
If the Product is deemed to be faulty within 30 days from date of original purchase, Radio Systems will organise for a replacement to be sent in advance of returning the faulty Product. A Post Bag will be included with the replacement Product for the return of the faulty Product. The Product must be returned within 7 days of receiving the replacement. If the Product is deemed to be faulty after 30 days from the date of original purchase, the consumer will be required to return the Product to Radio Systems at the consumer’s own expense. Radio Systems will test and replace the faulty unit or its components and return to the consumer free of charge, provided the Product is within its said warranty period. This warranty is in addition to other rights and remedies available to you under the law. Radio Systems goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Should you have any queries or require any further information, please contact our Customer Care Centre on 1800 786 608 (Australia) or 0800 543 054 (New Zealand).

For a list of patents protecting this product, please visit: www.radiosystemscorporation.com/patents