sportDOG FieldSentinel 825 Electronic Remote Training Collar User Guide

sportDOG FieldSentinel 825 Electronic Remote Training Collar User Guide

Warning Read all the safety information below before using the product.

Caution FieldSentinel is not a medical device and should not be used as a substitute for professionalmedical judgment. Itis not designed or intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation, treatment, or prevention of any condition or disease. Please consult your veterinarian priortomaking any decisionsrelated to your dog’s health. Always consider your dog’s health! DO NOT exercise your dog to the point of exhaustion.

• This productisintended to be used only forrecreational purposes and not for medical purposes, and is not intended to diagnose, monitor, treat, cure, or prevent any disease or condition.
• The heart rate, heart rate variability, and other readings are for reference only, and no responsibility is accepted for the consequences of any erroneousreadings.
• NOTICE: Avoid contact with spray cleaners & Deet as they could damage the product’s plastics.

To avoid serious risk or injury to your dog, it is important you complete the following steps in order before you begin using this system.

Thank you for choosing the SportDOG® Brand FieldSentinel. With proper use,thissystemwill help you train your dog efficiently and safely. The Quick Start Guide will get you and your dog started with this remote training system. For the best experience, review this guide thoroughly. For more detailed information, we recommend reading the complete manual online. You can easily access it with the QR code provided. It will include information on Collarstim ranges; pairing your Collarto the Handheld, etc.

Whats In The Box

How It Works

In addition to being a fully functional training e-collar, this system also monitors your dog’s health. Thiswill allow you to know how your dog is doing, even if he is not within eyesight, and quickly address any potentially dangerous health situations.

STEP 1: CHARGE THE HANDHELD & COLLAR

1. Connect the magnetic charger to the back of the Handheld by aligning the two and letting itsnap into place. TheHandheld takes 2 hoursto fully charge.

2. Snap the charging clip on the Collar by aligning the brass contacts on the clip to the connection points on the Collar and matching up the SportDOG® logos. The Collartakes 4 hours to charge.
   

3. Connect each of the USB ends on the charging cablesto the wall adapter and plug into a standard wall outlet. The Collar and Handheld Indicator Lights will be solid green while charging and flash green when fully charged.

HANDHELD: To power the Handheld ON or OFF, press and hold the power button (found on top) until it beeps.
COLLAR: To powerthe CollarON, press and release the power button (between the probes). The Collar will beep, and the Indicator Light will flash red or green depending on battery status. The health sensor lights will glow steady green.

To powerOFF, press and hold the button untilthe Collar beeps and lightisred.

STEP 2: GET TO KNOW THE HANDHELD & COLLAR

STEP 3: FIT THE COLLAR ON YOUR DOG

1. Your dog should be standing comfortably while fitting the collar.

2. Position the collar as high as possible on your dog’s neck and slightly to either side, not directly centered. Buckle the collarso that it fitssnuggly.

3. You should only be able to fit one finger between the strap and your dog’s neck. This will help ensure the health sensor and the contact points are both touching your dog’s skin. If your dog has a long or thick coat, trim the hair around the contact pointsto ensure contact with the skin.

STEP 4: LET THE COLLAR GET TO KNOW YOUR DOG

 Once the collar is fit on your dog and powered on, it needs up to 5 MINUTES to calibrate to your dog and start tracking vitals allowing your hunt/training session to start with a valid heart rate. Do not remove the collar orturn it off during thistime. Every time you put the collar on your dog, it is important to make sure you wait 5 minutes for the collar to calibrate before use. Also, keep the health monitor sensors are clean by using soap, warm water, and a microfiber cloth.

During this 5 minutes, there should be minimal motion of your dog. The system will do X when ready to be used and collecting health information.

STEP 5: FIND YOUR DOG’S RECOGNITION LEVEL

For effective training, it is important to find the best level ofstatic stimulation for your dog.

RECOGNITION LEVEL: The lowest level ofstatic stimulation at which your dog acknowledges feeling the stimulation through a reaction. This reaction can be flicking his ears, looking around in curiosity, or standing up from a sitting orlying position.

Always start at the lowest level and slowly increase as needed. Every dog is different, and their recognition level is not correlated to size or breed. Therefore, it is important to watch closely for any slight changes in behavior that demonstrates your dog is feeling the static stimulation.

1. Starting with the collar powered on and properly fitted on your dog,set the Handheld dial to Level 1. Power yourHandheld on by pressing the button asshown.

2. While watching your dog, pressthe Upper Button for 1 to 2 seconds. Look for any indication that your dog feels the static stimulation.

3. If your dog shows no reaction, increase the Intensity Dial to Level 2 and repeat this process until you find your dog’s Recognition Level. This is the level you should use when you begin a training exercise.

4. If you have progressed to the highest level on the dial (7) while searching for your dog’s Recognition Level and your dog continuesto show no response, check tomake sure the fit ofthe Collar is snug against your dog’s neck. Then go back to Level 1 and repeatthe process. If your dog still does notindicate he is feeling the static stimulation, you may need to trim the hair beneath the Contact Points or contact Customer Care.

HEALTH SENSOR ALERTS

Ifthe Collar detects a significant, potentially dangerous change in your dog’s vitals, yourHandheld will alert you by flashing a light atthe base of the antenna as well as emitting a tone and vibration.

To silence the alert, quickly press and release the power button on the Handheld. The tone and vibration will stop, butthe Alert LED will continue to flash until your dog’s vitalsreturn to normal. If you accidentally turn off the Handheld,simply turn back on. You will not need to wait the 5-minute initializing period.

We recommend if your Handheld alerts you, you go to your dog to assist them (e.g. put eyes on your dog and observe them, take a break, give your dog water). You may also consider loosing the collar and then fitting properly when vitals return to normal.

To accessmore information about heat-related illnesses,referto the adjacent QR code for tips on what to do if you notice your dog exhibiting certain signs.

CHANGING THE ALERT THRESHHOLD

If you find the Handheld is alerting you frequently when your dog’s condition seems normal, you can adjust the sensitivity of the alert by following the steps below:

1. Begin with the toggle switch down and the intensity dialsetto V/T

2. Pressthemode button on the back of the Handheld with the tip of a pen. The Indicator Light will be solid green.

3. Turn the Intensity Dial to your desired threshold (1, 2, or 3).

4. Press the left side button on your Handheld to set.

Contains: FCC ID: QOQ-GM240S, IC: 5123A-GM240S
This equipment complies with FCC and RSS-102 radiation exposure limits set forth for an uncontrolled environment and meets the FCC and RSS-102 radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator atleast 20 cmormore away fromperson’s body.

FCC
This device complies with part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation. If interference does occur to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult customer care, the dealer, or an experienced radio/TV technician for help.

CAUTION: Modification or changes to this equipment not expressly approved by Radio Systems Corporation may void the user’sauthority to operate the equipment.

References

• SportDOG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>