IGLOO IWCTT353CRHWH Hot and Cold Top Load Countertop Water Dispenser Instruction Manual
- June 6, 2024
- Igloo
Table of Contents
Hot & Cold Top Load Countertop Water Dispenser
IWCTT353CRHWH
Instructions and Recipes
All products are trademarks of Nostalgia Products LLC.
Worldwide design & utility patented or patents pending.
© 2020 Nostalgia Products LLC.
IGLOO® and the Igloo design are trademarks of Igloo Products Corp. All rights
reserved.
www.nostalgiaproducts.com
(rev. 11/05/20 LM)
Make every day a party!
Visit www.nostalgiaproducts.com for more
fun products.
SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can cause serious injury to
you and others.
All safety messages will follow the safety alert symbol.
All safety messages will tell you what the potential hazard is, tell you how
to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
Appliance Specifications:
110 Volts, 60 Hz, 550 Watts
THIS PRODUCT IS FOR USE IN 120V AC OUTLETS ONLY.
Refer to www.nostalgiaproducts.com/user-
manuals/ for the most updated
manual.
IMPORTANT SAFEGUARDS
A person who has not read and understood all operating and safety instructions
is not qualified to operate this appliance. All users of this appliance must
read and understand this Instruction Manual before operating or cleaning this
appliance.
When using electrical appliances, basic safety precautions should always be
followed, including:
-
Read all instructions before operating this appliance.
-
DO NOT TOUCH the hot surfaces. Use handles or knobs.
-
This appliance is NOT A TOY.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they are closely supervised and instructed concerning the use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children.
Children should be supervised to ensure that they do not play with the appliance. -
Close supervision is necessary when any appliance is used by or near children.
-
Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts, and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
-
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment. The customer service number is 920-347-9122.
-
Unplug from outlet when not in use, before removing parts, and before cleaning. Allow cooling before putting on or taking off any parts, and before cleaning.
-
DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or if the appliance has been damaged in any manner. Return the appliance to the nearest repair shop for examination, repair, or adjustment.
-
The manufacturer does not recommend the use of accessory attachments other than what is provided by the manufacturer. The use of attachments may cause injuries.
-
DO NOT use the appliance for anything other than its intended use.
-
DO NOT use outdoors. FOR HOUSEHOLD USE ONLY.
-
DO NOT place on or near a hot gas or electric burner, or in a heated oven.
-
DO NOT let cord hang over the edge of table or counter, or touch hot surfaces.
-
NEVER leave the unit unattended while in use or when plugged into an outlet.
-
Extreme caution must be used when moving an appliance containing hot food.
-
Always attach the plug to the appliance first, then plug the cord in the wall outlet. To disconnect, turn any control to “off,” then remove the plug from the wall outlet.
ADDITIONAL IMPORTANT SAFEGUARDS
Operating Safety Precautions
- Prior to use, this dispenser must be properly assembled and installed in accordance with this manual.
- This dispenser is intended only for water dispensing. Do NOT use other liquids.
Do NOT use for other purposes. Never use other liquids in the dispenser other than known and microbiologically safe bottled water. Warranty is void if used with any other liquids, such as coffee, tea, juices, beer or wine.
Instructions for the Electrical Cord and Plug
-
ELECTRICAL SHOCK HAZARD: Failure to follow these instructions can result in death, fire, or electrical shock.
• Plug into a grounded 3 prong outlet.
• DO NOT remove the ground prong.
• DO NOT use an adapter.
• DO NOT use an extension cord. -
This unit MUST be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This unit is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
-
WARNING: Improper use of the grounding plug can result in a risk of electric shock. If the plug does not fit fully into the outlet, contact a qualified electrician. Do not attempt to modify the plugin anyway.
-
A short power-supply cord is provided to reduce the risk resulting from becoming entangled or tripping over a long cord.
The manufacturer does not recommend using this machine in countries that do not support 120V AC even if a voltage adapter, transformer, or converter is in use.
SAVE THESE INSTRUCTIONS!
INTRODUCTION
Thank you for purchasing the HOT & COLD WATER COUNTERTOP TOP LOAD WATER COOLER from IGLOO! With the Igloo Hot & Cold Top Load Water Cooler, ease is at your fingertips! This top-loader gives you ice-cold and hot water in just seconds! This water cooler allows you to load 3 or 5-gallon bottles with no plumbing required! There is a child safety lock for the hot button so there are no accidents. Satisfy your thirst with cool water or relax with a hot beverage using the brand you can trust!
- Top loading cooler for hot and cold water
- Uses standard 3 and 5-gallon bottles (not included)
- Compressor Cooling
- Direct water line hookup available
- Hot, room temperature & cold dispensers with a hot-button safety lock
- Overheating protection for hot tank
- Removable drip tray for an easy cleanup
- Dispensing area suitable for up to 8.5” bottle
- Hot water tank capacity: 1L/ Coldwater tank capacity: 3.2L
- Water temperature: Hot 203°F/ Cold 40°F
- Hot and Cold On/Off switches
PARTS & ASSEMBLY
- Hot Water Indicator Light
- Cold Water Indicator Light
- Cold, Room & Hot Water Spigot
- Removable Drip Tray
- Adjustable Feet
- Hot Water Push Button Dispenser/Safety Lock
- Room Temperature Water Push Button Dispenser
- Cold Water Push Button Dispenser
- Cold Water On/Off Switch
- Hot Water On/Off Switch
ASSEMBLY
Use EXTREME CAUTION when handling the appliance. When taking out of package,
it is recommended to lay the box safely on its side. For the most part, the
HOT & COLD WATER TOP LOAD WATER COOLER is assembled. Once unpacked and
standing upright, the drip tray will need to be inserted.
Location Requirements:
- Install in the area where it is protected from the elements including the direct sun.
- Install and use only on a hard, flat, and level surface.
- Do NOT place the dispenser inside an enclosed space or cabinet.
- Position the dispenser no closer than 4 inches from the wall with at least 4 inches clearance on the sides to permit free airflow.
- Service should only be performed by a certified technician.
WATER COOLERS
It is very easy to replace 3 or 5-gallon coolers (not included). NOTE:
Excessive weight hazard – It is recommended to use two or more people to move
and install bottles. Failure to do so can result in injury.
With reusable cap:
- If your water bottle has a reusable cup on the end with a plug, safely place the 3 or 5-gallon bottle onto the bottle probe and the nozzle should fit securely onto the base. Once secure, you will begin to see water flowing from the bottle to the tank.
If there is no reusable cap:
- Stand with your feet shoulder-width apart and bend down to grab the new water bottle.
- Lift the bottle up and slowly tip it to a 45-degree angle to allow water to begin dripping into the cooler.
- Place the bottle into an upright position as the flow of water into the cooler begins to increase, and then secure it onto the base. Once secure, you will begin to see water flowing from the bottle to the tank.
HOW TO OPERATE
WARNING: This unit is intended for water dispensing only. Do NOT use
other liquids. Do NOT use it for other purposes. Warranty is void if used with
any other liquids such as coffee, tea, juices, beer, or wine. This dispenser
has been designed to use water bottles with a 3 or 5-gallon capacity. Do NOT
use alternative bottles.
Initial Set-Up
To avoid damage to the compressor, allow the unit to sit upright for at least
4 hours prior to operation. NOTE: Make sure that switches are ON. Each of the
Hot and Cold switches are located in the back of the water cooler.
- Remove the tamper seal from the bottle cap. Do not remove the plastic cap.
- Lift the bottle safely (see assembly above) and place the bottle until it’s secure and the bottle is seated.
- Plug the cord into a properly grounded wall outlet.
WARNING: Always make sure that the cord is away from a water source.
Dispensing Cold Water
After setup, it will take up to 6 hours to get the water to its maximum cold temperature. When it reaches max temperature, the green light will turn off.
- Place bottle, glass, or pitcher below the cold water tap.
- Press the cold water button downward to start dispensing water.
- Release the button once the desired fill level is achieved.
Dispensing Hot Water
After setup, it will not take long to reach the maximum hottest temperature.
When it reaches the hottest temperature, the red light will turn off.
NOTE: For safety, there is a lock on the dispensing button.
- Place bottle, glass, pitcher, pot below the hot water tap.
- Release the child-safety lock by sliding the red button and pressing the hot water button downward at the same time to start dispensing water.
- Release the button once desired fill level is achieved.
NOTE: Be careful when dispensing hot water as the temperature can reach 203 °F.
Replacing An Empty Bottle
Replace the bottle as soon as you notice that it is empty.
- Lift the bottle straight up to disengage it from the bottle probe.
- Remove the tamper seal from the bottle cap of the NEW bottle. DO NOT remove the plastic cap.
- Lift the bottle and insert it (assembly directions above). Apply slight pressure until the plug inside the cap pushes in and the bottle is secure.
HELPFUL TIPS
THE DISPENSER IS NOT WORKING
- Make sure that the power cord is properly connected to a working outlet.
WATER IS LEAKING
- Replace the water bottle. The most common cause is a cracked bottle.
NO WATER IS COMING OUT
- Make sure the bottle is not empty. If so, replace it.
- Make sure that you fully press the water control buttons.
WATER DISPENSER IS NOT COLD
- Make sure the cold switch is ON. The switch is located in the back of the water cooler.
- It can take up to six hours after setup to dispense the coldest water.
- Make sure the back of the dispenser is at least 4 inches from a wall and that air is free to flow on all four sides of the dispenser.
WATER DISPENSER IS NOT HOT
- Make sure the cold switch is ON. The switch is located in the back of the water cooler.
- It can take up to 30 minutes after set up to dispense the hottest water. Each time hot water is dispensed, it needs time to heat up again.
- Make sure the back of the dispenser is at least 4 inches from a wall and that air is free to flow on all four sides of the dispenser.
DISPENSER IS NOISY
- Make sure that the dispenser is positioned on a level surface.
CLEANING & MAINTENANCE
General Cleaning
General cleaning should be performed as needed and only takes five minutes or
less.
- Clean the cabinet surfaces using a soft cloth and warm, soapy water. Rinse.
- Wipe dust in the back of the water cooler to improve efficiency.
- Remove drip tray cover and hand wash. Take a cloth and warm, soapy water to rinse the inside of the drip tray. Rinse.
- Reattach drip tray.
Cleaning Water Lines & Cold Reservoir
Cleaning the water lines and reservoirs is recommended to happen once every
three months.
NOTE : Recommended to do before loading a new 3 or 5-gallon jug.
- Unplug the power cord from the outlet.
- Remove water cooler bottle.
- Remove the plastic water guard and clean with warm, soapy water. Rinse.
- Fill stainless steel reservoir with a mixture of water and bleach and let it sit for 30 minutes.
- Remove the cleaning mixture by dispensing it from both taps into a bowl or pitcher.
- Wipe inside of reservoir with a soft cloth and fill with water.
- Dispense water from both taps into a bowl or pitcher.
- Repeat the rinsing cycle if chlorine taste persists.
- Install a new bottle of water and plug in the power cord into a grounded outlet.
RETURNS & WARRANTY
SHOULD YOUR UNIT NOT WORK OR IF DAMAGED WHEN YOU FIRST TAKE IT OUT OF THE BOX,
PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY.
HOT & COLD COUNTERTOP TOP LOAD WATER DISPENSER / IWCTT353CRHWH
Should you have any questions, please contact us via email or at the customer
service number listed below between the hours of 8:00 AM and 5:00 PM, Monday
through Friday, Central Standard Time.
Distributed by:
Nostalgia Products LLC
1471 Partnership Dr.
Green Bay, WI 54304-5685
Customer Service
Phone: 920-347-9122
Web: www.nostalgiaproducts.com
Customer Service Inquiry
To submit a Customer Service inquiry, go to
www.nostalgiaproducts.com and fill out the
Customer Service Inquiry form and click the Submit button.
A representative will contact you as soon as possible.
Product Warranty Terms
Nostalgia Products LLC (the “Company”) hereby warrants that for a period of
one (1) year from the date of original purchase, this product will be free of
defects in material and workmanship under normal home use, provided that the
product is operated and maintained in accordance with the operating
instructions. As the sole and exclusive remedy under this warranty, the
Company will at its discretion either repair or replace the product found to
be defective, or issue a refund on the product during the warranty period.
This warranty is only available to the original retail purchaser of the
product from the date of initial retail purchase, and is only valid with the
original sales receipt, as proof of purchase date is required to obtain
warranty benefits. All warranty claims must be brought to the attention of the
Company within the warranty period and no later than 30 days of the failure to
perform. This warranty does not cover normal wear or damage caused by
shipping, mishandling, misuse, accident, alteration, improper replacement
parts, or other than ordinary household use. You may be required to return the
product (with shipping prepaid by you) for inspection and evaluation. Return
shipping costs are not refundable. The Company is not responsible for returns
damaged or lost in transit. Unless otherwise specifically permitted by the
operating instructions, this warranty applies to indoor household use only. In
order to obtain service under this warranty, please contact the Company at the
telephone number listed above or by filling out the Customer Service Inquiry
Form located at www.nostalgiaproducts.com.
Warranty valid only in USA and Canada.
This warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular purpose,
which are hereby excluded to the extent permitted by law. In no event shall
the Company be liable for any indirect, incidental, consequential, or special
damages arising out of or in connection with this product or the use thereof.
Some states, provinces or jurisdictions do not permit the exclusion or
limitation of incidental or consequential damages, so the foregoing exclusion
or limitation may not apply to you.
This warranty does not apply to re-manufactured merchandise.
Please read the operating instructions carefully. Failure to comply with the
operating instructions will void this warranty.
For more information, visit us online
atwww.nostalgiaproducts.com.
Like us on Facebook at
www.facebook.com/NostalgiaElectrics.
Follow our boards on Pinterest at
www.pinterest.com/nostalgiaelctrx.
Tweet along with us on Twitter at
www.twitter.com/NostalgiaElctrx.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>