TELTONIKA RUT360 LTE Industrial Router User Guide

: June 6, 2024
: teltonika

Table of Contents

Wiki knowledge base
FRONT VIEW
BACK VIEW
POWER SOCKET PINOUT
HARDWARE INSTALLATION
LOGIN TO DEVICE
TECHNICAL INFORMATION
SAFETY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RUT360
Quick Start Guide v1.1

TELTONIKA RUT360 LTE Industrial Router

Wiki knowledge base

https://wiki.teltonika-networks.com/

FRONT VIEW

TELTONIKA RUT360 LTE Industrial Router - front view

BACK VIEW

TELTONIKA RUT360 LTE Industrial Router - back view

POWER SOCKET PINOUT

TELTONIKA RUT360 LTE Industrial Router - power socet

I/O: programmable Input/Output pins (Open Collector output max 30 V, 300 mA or Digital input where 0-6 V detected as a logic low and 8-30 V – logic high).

HARDWARE INSTALLATION

TELTONIKA RUT360 LTE Industrial Router - hardware

Push the SIM holder button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
Attach Mobile and WiFi antennas.
Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to the LAN port.

To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL ﬁeld of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory and you will not be able to interact with the router’s WebUI before you change the password.
When you change the router’s password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool used to set up some of the router’s main operating parameters.
Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TELTONIKA RUT360 LTE Industrial Router - LOGIN TO
DEVICE

TECHNICAL INFORMATION

Radio specifications

RF technologies| 3G, 4G, 1NiFi
Max RF power| 24 dBm@WCOMA. 23 dBm@LTE, 20 dBm@WiR
**Bundled accessories specifications*
Power adapter| Input: 0.6 A@100-240 VAC, Output 12 VDC, 1.5 A, 4 pin plug
Mobile antenna| 698-960/1710-2690 MHz, 50 a VSWR<3, gain 4 dBi, omnidirectional, SMA male connector
W1IR antenna| 2400-2483.5 MHz, 500. VSWR<2, gain” 5 dBi, omnidirectional, RP- SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for compliance with the legal regulations.

SAFETY INFORMATION

RUT360 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.
Hereby, TELTONIKA NETWORKS declares that this RUT360 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following Internet address: https://wiki.teltonika- networks.com/view/RUT360_CE/RED
Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to conﬁgure it. More information on https://wiki.teltonika-networks.com/
This sign means that all used electronic and electric equipment should not be mixed with general household waste.
www.teltonika-networks.com

This sign means that the product meets the requirements of the applicable EU directives.
©2020 Teltonika Networks