JASCO 46562 In-Wall Z-Wave Smart Switch Instruction Manual
- June 6, 2024
- JASCO
Table of Contents
- JASCO 46562 ZW4008 In-Wall Smart Switch Instruction Manual
- Tools You Will Need
- Getting to know your new Z-Wave device
- Multi-switch wiring
- Single-switch wiring
- Wire gauge requirements
- Wire strip length
- Basic operation
- Manual control
- Cycle LED light
- Adding your device to a Z-Wave network
- To remove and reset the device
- To return your switch to factory defaults
- Changing paddle color
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JASCO 46562 ZW4008 In-Wall Smart Switch Instruction Manual
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video. Scan QR code or visit goo.gl/gAVDRo
*Convert any smart control to a multi-location switch**
*For a list of compatible devices, visit ezzwave.com
To purchase an add-on switch or for more details, visit ezaddonswitch.com.
Multiple Paddle
Colors Available
ezzwave.com/paddlecolors
Purchase additional items at EZzwave.com or visit your local retailer.
DO NOT RETURN THIS PRODUCT TO THE STORE
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.byjasco.com/support.
- No user-serviceable parts in this unit.
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES
CAUTION:
- DO NOT EXCEED RATINGS
- DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
- DO NOT USE TO CONTROL RECEPTACLES
- FOR INDOOR USE ONLY
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period.
SPECIFICATIONS
ZW4008
Power: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 960W incandescent, 1/2HP motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the
closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independently mounted (vertical position only), operating
control: type 1.c action, pollution degree (2), impulse voltage (2500V),
software class A
For indoor use only Specifications subject to change without notice due to
continuing product improvement
ZW4008DV
Power: 120/277VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 960W (120VAC)/1385W (277VAC) incandescent, 1/2HP (120/277VAC)
motor or 1800W (15A) (120/277VAC) resistive
Range: Up to 150ft. line of sight between the wireless controller and the
closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independently mounted (vertical position only), operating
control: type 1.c action, pollution degree (2), impulse voltage (4000V),
software class A
For indoor use only
Specifications subject to change without notice due to continuing product
improvement
Tools You Will Need
IMPORTANT!
The fixture controlled by the Z-Wave In-Wall Smart Switch must not exceed 960W
incandescent, 1800W (15A) resistive or 1/2HP motor. The switch is designed
only for use with permanently installed fixtures.
Getting to know your new Z-Wave device
- Turn ON/OFF manually or remotely via the Z-Wave controller
- Can be included in multiple groups and scenes
- May be used in single-pole installation or with up to four add-on switches (model 46560) in 3-way or 4-way wiring configurations
- Compatible with all LED/CFL and incandescent bulbs
- Auto line/load detection
- Interchangeable paddle switch — white & light almond paddle in package
- Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
- Blue LED indicates switch location in a dark room
- Z-Wave certified for simple pairing and integrated home automation
- Screw terminal installation — requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way or 4-way installation
- This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
A. Ground (Green/Bare)
B. Line or Load (Black)
C. Line or Load (Black)
D. Traveler (Red/Other)
E. Neutral (White)
F. Top rocker — press & release to turn switch on
G. Bottom rocker — press & release to turn switch off
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture
at the service panel. All wiring connections must be made with the POWER OFF
to avoid personal injury and/or damage to the switch.
This device is intended for installation in accordance with the National
Electric Code and local regulations in the United States or the Canadian
Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation, consult a qualified
electrician.
Multi-switch wiring
For 3-way installations, please refer to add-on switch (model 46560) manual
Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate or décor. Please proceed to section 5.
-
Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing. -
Remove wallplate.
-
Remove the switch mounting screws.
-
Carefully remove the switch from the switch box. DO NOT disconnect the wires.
There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
5. Disconnect the wires from the existing switch. Label wires according to the previous terminal connection.
Observe important wiring information
IMPORTANT! This switch is rated for and intended to only be used with copper wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, neutral, ground and traveler connections.
Wire strip length
For attachment using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
-
Connect the green or bare copper ground wire to the GROUND terminal.
-
Connect the black wire from the light to either LINE/LOAD terminal.
-
Connect the black wire from the electrical service panel (hot) to the remaining LINE/LOAD terminal.
-
Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
Note: The traveler terminal is only used for 3-way or 4-way wiring and should remain unused if the switch is being installed in a 2-way system (one switch & one load). -
Insert switch into the switch box being careful not to pinch or crush wires.
-
Switch must be independently mounted (vertical position only).
-
Secure the switch to the box using the supplied screws.
-
Mount the wallplate.
-
Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected fixture can be turned ON/OFF in two ways:
- Manually from the front panel of the switch
- Remotely with a Z-Wave controller
Manual control
The front panel rocker switch allows the user to turn ON/OFF the connected fixture.
- To turn the connected fixture ON, press and release the top of the rocker.
- To turn the connected fixture OFF, press and release the bottom of the rocker.
Cycle LED light
The LED below the switch acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
- LED is ON when the load is OFF (guide light in the dark) (default)
- LED is ON when the load is ON (indicates the switch is ON)
- LED is always OFF
- LED is always ON (illuminates switch in the dark)
Adding your device to a Z-Wave network
- Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
- Once the controller is ready to add your device, press the top or bottom of the wireless smart switch (rocker).
You have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller.
If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.
If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code.
Figure 1:
To remove and reset the device
- Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
- Once the controller is ready to remove your device, press the top or bottom of the wireless smart switch (rocker).
To return your switch to factory defaults
- Quickly press ON (top) button three times, then, immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully.
Note: This should only be used if your network’s primary controller is missing or otherwise inoperable.
Changing paddle color
This step is optional. Before installation, you may want to change the color of the paddle to match your wallplate or décor.
- Lift the air gap tab at the base of the paddle.
- Push side tabs in on one side and then the other to release paddle. Lift the cover up and off.
- Simply put the new paddle onto the switch by inserting the air gap and side tabs and snapping securely into place.
Once this step has been completed, return to section 3.
The add-on switch is required for multi-switch 3-way or 4-way installations.
Connecting the traveler terminal of this switch to a standard, non-Jasco switch will cause damage or result in improper function. If this switch is part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply power until add-on switch (model 46560) is correctly installed. For more information on 3-way or 4-way installations, view the manual or quick-start guide for the add-on switch.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
This device supports Association Command Class (3 Groups)
- Association Group 1 supports Lifeline, Binary Switch Report
- Association Group 2 supports Basic Set and is controlled by pressing the ON/OFF button with the local load
- Association Group 3 supports Basic Set and is controlled by double pressing the ON/OFF button
- Each Association Group supports 5 total nodes
FCC/IC
This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
Responsible Party – US Contact Information
ZW4008:
FCC — U2ZZW4008 | IC: 6924A-ZW4008
ZW4008DV:
FCC — U2ZZW4008DV | IC: 6924A-ZW4008DV
Jasco Products Company | Model: ZW4008/46562/ZW4008DV/43104
10 E. Memorial Rd., Oklahoma City, OK 73114 |
1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their respective owners.
MADE IN CHINA
DISTRIBUTED BY
JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
©JASCO 2020 | 46562 | ZW4008 | 43104 | ZW4008DV 5/20/20 v3
References
- Add-On Switches
- Z-Wave by Jasco
- Add-Ons
- 14318: Jasco Z-Wave Plus In-Wall Smart Switch - YouTube
- Jasco
- Jasco
- Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>