EDIFIER W830BT Wireless Stereo Headphones User Manual

W830BT
Wireless Stereo Headphones
Operating instructions

Introduction

Before use the headphone, please read these operating instructions carefully. Keep the operating instructions safe for future reference.

Features

• 40mm drivers deliver the deep powerful bass ideal for all music genres
• 90°-degree swivel ear pads optimize movement while ensuring overall comfort
• Bluetooth V4.1 supports HSP, HFP, A2DP, and AVRCP protocol
• CSR8645 chip with AAC and Qualcomm® aptX™ audio decoding technology
• Supports 95 hours of continuous play
• Bluetooth connects up 10 meters
• Sleek metal bracket and headband styled with soft leather ear caps and head cushion
• Accessories include: Travel case x1 3.5mm audio cable x1 USB charging cable x1

Specifications

Bluetooth Version: Bluetooth V4.1
Bluetooth Profiles: HFP, HSP, A2DP, AVRCP
Audio Decoder: Qualcomm® aptX™
Operating distance: 10m
Operating Time: About 95 hours
Charge Time: About 4 hours
Rated Power Input: 5.0V 1A
Frequency Range: 20Hz-20KHz
Sensitivity (SPL): 96dB
Nominal Impedance: 24ohm
Frequency Band: 2.402GHz – 2.480GHz
RF Power Output: ≤20 dBm (EIRP)

Box Content

Operating Instructions

I. Diagram

1. Press: volume increase /press and hold: next track
2. Multi-function key
3. Press: volume decrease/press and hold: previous track
4. micro USB charging port
5.  3.5mm audio jack

II. Charge batteries
The headset is equipped with a built-in rechargeable battery. Fully charge the battery before first use. While in use, the headset will beep and flash red light to indicate battery low. You shall recharge the device.

1. Attach the USB charge cable to a standard USB power adapter.
2. Attach the charge cable to the Micro USB charge port on the headset.
3. Charge time: approximately 4 hours for a full charge.

Warning: The rechargeable batteries that provide power for this product must be disposed of properly for recycling. Do not dispose of batteries in fire to prevent an explosion.

Using the Headset

I. ON/OFF

Function| Operation Indicator|
---|---|---
ON| Long press the multifunction key for 3 seconds| The blue light flashes quickly
OFF| Long press the multifunction key for 3 seconds| Indicator off

II. Connection

Bluetooth connection
Please complete the connection with your mobile before use.
Follow the steps below:

• The distance between your mobile and the headset should be kept within 1m. The closer the better.

• Switch on the headset. Press and hold the multifunction key for 5 seconds to enter pairing mode.

• Enable your mobile’s Bluetooth and search for Bluetooth devices Select ”EDIFIER W830BT” to pair. Once successfully paired, LED flashes blue slowly and you hear a prompt beep.
  Note:

• While in pairing state, if a connection cannot be established within 3 minutes, it will automatically exit the pairing mode;

• If prompted for a passkey, enter “0000”;

• Once successfully paired, the headset and your mobile will remember each other. When the headset is turned on again, it will connect to the last connected device automatically.

NFC connection
If your Bluetooth mobile supports NFC (Near Field Communication), enable your mobile’s NFC function first and switch on the headset. Then touch the NFC  area of W830BT with the NFC area of your mobile to pair your devices.

Note:

• When the mobile hibernates or is screen-locked, it cannot pair with NFC.
  

• The first time you try to pair, it requires keeping your mobile in touch with W830BT for a slightly longer time. Wait till W830BT enters the pairing mode before you take away the mobile.

• If no device is connected, you may use NFC to establish pairing; if a device is NFC already connected, the NFC function can also be used to disconnect.

Pair another device
The headset can simultaneously connect two Bluetooth devices.
Follow the steps below:

• Pair your headset with Device 1.
• Switch off the headset. Long press the multi-function key to restart the headset and enter pairing mode. Connect device 2.
• Now operate on device 1. Tap the headset in Bluetooth connection settings to connect and complete pairing with two devices.

Note: When two connected mobiles have different operating systems (e.g. One on Android™ and the other one on iOS®), certain cross-system operations may  show some delay (e.g. The song in mobile A will pause while play the song in mobile B). This is considered normal.

Making calls
Basic operations

Function

| Headset status|

Operation

---|---|---
Answer a call| Incoming ring| Short press the multi-function key
Reject a call| Incoming ring| Long press the multi-function key for approx. 2 seconds
End a call| Talking| Short press the multi-function key
Increase volume| Talking| Tap the volume + key
Decrease volume| Talking| Tap the Volume – key
Direct a call to the mobile| Talking| Long press the multi-function key for approx. 2 seconds
Direct a call to the headset| Talking| Long press the multi-function key for approx. 2 seconds
Mute the mic| Talking| Long press the volume — key for approx. 2 seconds
Unmute| Talking (with mic muted)| Long press the volume + key for approx. 2 seconds
Call back last

call

| Device connected| Long press the multi-function key for approx. 2 seconds
Enable voice assistant| Device connected| Double press the multi-function key

Three-way calling

Function

| Headset status|

Operation

---|---|---
Answer new call and| Second incoming| Tap the multi-function key once
end the current call| call
Answer the new calls and keep| Second incoming| Tap the multi-function key twice
the current call on hold| call
Switch between calls| Talking (on hold)| Double-tap the multi-function key
End current call| Talking (on hold)| Tap the multi-function key once

Calls with two mobiles connected

Function

| Headset status|

Operation

---|---|---
End call with mobile 1 and answer a call from mobile 2| Talking with mobile 1 while 2nd mobile calling| Tap the multi-function key once
Put the call from mobie 1 on hold and answer the call from mobile 2| Talking with mobile 1 while 2nd mobile calling| Tap the multi-function key twice
Switch calls| Talking with one while the other call is on hold| Double-tap the multi-function key
End the current call and switch back to the mobile on hold| Talking with one call while the other call is on hold| Tap the multi-function key once

Play music
Bluetooth audio mode
When the headset is connected to a mobile that supports Qualcomm® aptX™, you may enjoy WIFI music via the headphones:

Note:

• When the headset is turned up to its maximum volume, you will hear a prompt tone from the headset.

AUX IN audio mode
The headset supports AUX IN audio input. Using 3.5mm to 3.5mm audio cable to connect the headset to a Jmusic player and enjoy the music on line.
Note:

• Plugging in a 3.5mm audio cable will turn off the headset and automatically disconnect the connection with the Bluetooth. AUX IN audio input is now in effect.
• If you want to go back to Bluetooth, unplug the 3.5mm audio cable and restart the headset to pair.

Restore factory setting

The headphone is under power off and charging status, press and hold the Volume

• key and volume – key simultaneously for about 3 seconds. The blue light flashes 3  times quickly. The factory settings are restored.
  Note:
  Once the factory settings are restored, the pairing list of the headphone is erased. When you power on the headphone again, it will automatically begin the pairing process rather than automatic connecting. If it needs to connect a device, you will have to go through the pairing again.

Maintenance

• Do not place the product in wet places to avoid adverse effect to internal circuits of the product.
• Do not expose the product to direct sunlight or heat. The high temperature will shorten electronic components’ life, damage the battery, and cause the deformation of certain plastic parts.
• Do not expose the product to excessive cold to avoid damage to internal circuits.
• Do not attempt to disassemble the product. A non-professional is likely to damage the product.
• Do not drop, intensively vibrate, or impact the product with hard object. It will damage the internal circuits.
• Do not clean the headset with harsh chemical solvents.
• Do not scratch the product surface with sharp objects. It will damage the housing and appearance.

In the event the product does not work properly, take it to an authorized service center. The staff will help you solving the problem.

FAQs

Red light flashes in place of blue.

• It tells that your headset battery is low and needs to recharge. The red light does not light up during charging.
• Make sure the charging device connects to the headset properly.
• The battery hibernates when the headset is not used for an extended period of time. In this case, it needs about 30 minutes of charge before the red light lights up.

Don’t hear anything in the headset.

• Make sure the headset is on.
• Make sure the headset is set to a proper volume.
• Make sure the headset has a valid connection with the mobile.
• Make sure the headset is within a normal working range.

Headset’s call quality is bad.

• Make sure the mobile is in a location with a strong signal.
• The headset has an effective working range of 10m. Please make sure the headset is within working distance without obstacles between the headset and the mobile.

During playing, why the headset cannot perform controls over a pause, resume, last song, and next song?

• This function requires that the device paired with your headset must support AVRCP (Audio/Video Remote Control Profile).

Cannot use NFC for pairing.

• Make sure your mobile’s NFC function has been enabled.
• When pairing at the first time, you need to keep your mobile in contact with the headset for about 3 seconds until the blue and red lights of the headset flash alternatively before taking away the mobile or a pairing may not be successful.

CAUTION
The danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type.
A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

• “To prevent possible hearing damage, do not listen at high volume levels for long periods.”
• “Fully understand user manual before use.”
• “Ensure your player at low volume levels or power off before you leaving.”

Correct Disposal of this product. This marking indicates that this product should not be disposed of with another household disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

WARNING!
The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
For products with a removable battery, the battery must be properly recycled or disposed of. For products with built-in batteries, disassembling is prohibited.
Never disassemble, hit with force, squeeze batteries or dispose of batteries in fire. Do not expose batteries in conductive materials, liquid, fire, or heat. Do not let metal objects contact two battery poles. If the battery looks swollen, leaking, discolored, having odor or any abnormal appearance, stop using it. Do not use the battery after being immersed in water.
Improper use of battery may lead to explosion or leakage, causing skin burn or other injuries; in the event of battery leakage, handle it with care and immediately dispose of the battery in the manner in compliance with applicable laws and regulations in your locality.

To guarantee your personal safety, please do not wear or keep earphones in the vicinity (closer than 10cm) of a pacemaker. Supervise children when using the equipment, the product is not a toy.
Earphone listening at high volume levels – particularly, over extended periods of time – may damage your hearing. The operation of switches on your hi-fi system or plugging in the earphones may cause clicks which at high volume setting may affect your hearing. Therefore, always set the volume control to a minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earphones.
For traffic safety, do not use earphones while driving or cycling.

Edif ier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
© 2019 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade, the information contained herein may be subject to change from time to time without prior notice.

Products of EDIFIER will be customized for different applications. Pictures and illustrations shown in this manual may be slightly different from the actual product.  Images are for illustrative purposes only and may differ from the actual product.
V1.5 IB-200-W0830B-03

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>