TELTONIKA FMB002 Easy OBDII Tracker with Bluetooth User Manual

: June 6, 2024
: teltonika

FMB002

Easy OBDII tracker

Quick Manual

v1.4

Know your device

Top view Bottom view (without cover)

TELTONIKA FMB002 - Figure 1 - Top View

Figure 1 FMB002 device view

OBDII connector
Navigate LED
Micro-USB
Battery socket
Nano-SIM slot
Status LED

Pinout

Table 1 OBDII pinout

PIN NUMBER	PIN NAME	DESCRIPTION
2	PWM_BUS+/VPW
4	GND (-)	Ground
5	GND (-)	Ground
6	CAN_H	CAN high
7	K-Line
10	PWM_BUS-
14	CAN_L	CAN low
15	L-Line
16	VCC (12 – 30)V DC(+)	Power supply (+12-30 V DC)

TELTONIKA FMB002 - Figure 2

Figure 2 FMB002 OBDII socket pinout

Set up your device

How to insert Micro-SIM card and connect the battery

1. Open the top cover of the device. Cover is opened by unclipping it at the recessed corner.
2. Insert Nano-SIM card as shown with PIN request disabled or read our Wiki how to enter it later in Teltonika Configurator. Make sure that Nano-SIM card is fitted properly into the holder.
3. Connect the battery as shown in the figure.
4. After configuration , see “PC Connection (Windows)”, attach device cover back.

Device is ready to be mounted.

(1)
Figure 4 Device case removal

(2)
Figure 3 Nano-SIM card insert

(3)
Figure 5 Battery connection

(4)
Figure 6 Attach device cover back

PC Connection (Windows)

Power-up FMB002 with DC voltage (12 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications”.
Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Micro-USB cable
– You will need to install USB drivers, see “How to install USB drivers (Windows)”
• Using Bluetooth
– FMB002 Blue-tooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named –
“ FMBxxx_last_7_imei_digits ”, without LE in the end. Enter default password 5555 , press Connect and then select Done.
You are now ready to use the device on your computer.

How to install USB drivers (Windows)

Please download COM port drivers from here.
Extract and run TeltonikaCOMDriver.exe.
Click Next in driver installation window.
In the following window click Install button.

Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first FMB002 device will have default factory settings set. These settings should be changed according to the user’s needs. Main configuration can be performed via Teltonika Configurator software. Get the latest Configurator version from here. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

Table 2 MS .NET requirements

MS .NET REQUIREMENTS

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner (Figure 7 Language selection).

TELTONIKA FMB002 - Figure 7

Figure 7 Language selection

Configuration process begins by pressing on connected device (Figure 8 Device connected via USB).

TELTONIKA FMB002 - Figure 8

Figure 8 Device connected via USB

After connection to Configurator Status window will be displayed (Figure 9 Configurator Status window).

TELTONIKA FMB002 - Figure 9

Figure 9 Configurator Status window

Various Status window tabs display information about GNSS, GSM, I/O , Maintenance and etc. FMB002 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

1. TELTONIKA FMB002 - 1 Load from device Load from device – loads configuration from device.
2. TELTONIKA FMB002 - 2 Save to device Save to device – saves configuration to device.
3. TELTONIKA FMB002 - 3 Load from file Load from file – loads configuration from file.
4. TELTONIKA FMB002 - 4 Save to file Save to file – saves configuration to file.
5. TELTONIKA FMB002 - 5 Update firmware Update firmware – updates firmware on device.
6. TELTONIKA FMB002 - 6 Read records Read records – reads records from the device.
7. TELTONIKA FMB002 - 7 Reboot device Reboot device – restarts device.
8. TELTONIKA FMB002 - 8 Reset configuration Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured.
More details about FMB002 configuration using Configurator can be found in our Wiki.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.

Quickly set up your device by sending this SMS command to it:
” setparam 2001 :APN; 2002 :APN_username; 2003 :APN_password; 2004 :Domain; 2005 :Port; 2006 :0″

Note: Before SMS text, two space symbols should be inserted.

TELTONIKA FMB002 - Default configuration settings

GPRS settings:

2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

Default configuration settings

Movement and ignition detection:

TELTONIKA FMB002 - Movement detection Vehicle movement will be detected by accelerometer
TELTONIKA FMB002 - Ignition detection Ignition will be detected by vehicle power voltage between 13,2 – 30 V

Device makes a record On Moving if one of these events happen:

TELTONIKA FMB002 - 300s passes 300 seconds passes
TELTONIKA FMB002 - Vehicle turns 10 degrees Vehicle turns 10 degrees
TELTONIKA FMB002 - Vehicle drives 100m Vehicle drives 100 meters
TELTONIKA FMB002 - Speed 10 km h Speed difference between last coordinate and current position is greater than 10 km/h

Device makes a record On Stop if:

TELTONIKA FMB002 - 1h passes 1 hour passes while vehicle is stationary and ignition is off

Records sending to server:

TELTONIKA FMB002 - 120s passes If device has made a record it is sent to the server every 120 seconds

After successful SMS configuration, FMB002 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.

Mounting recommendations

Connecting the device to the vehicle:
– Find OBDII connector in your vehicle (Figure 10. Most common OBDII connector locations.).

TELTONIKA FMB002 - Figure 10

Figure 10. Most common OBDII connector locations.

LED indications

Table 3 Navigation LED indications

BEHAVIOUR	MEANING
Permanently switched on	GNSS signal is not received
Blinking every second	Normal mode, GNSS is working
Off	GNSS is turned off because: Device is not working or Device is in sleep

mode
Blinking fast constantly| Device firmware is being flashed

Table 4 Status LED indications

BEHAVIOUR	MEANING
Blinking every second	Normal mode
Blinking every two seconds	Sleep mode
Blinking fast for a short time	Modem activity
Off	Device is not working or Device is in boot mode

Basic characteristics

Table 5 Basic characteristics

MODULE

Name| Teltonika TM2500
Technology| GSM, GPRS, GNSS, BLUETOOTH
GNSS
GNSS| GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver| 33 channel
Tracking sensitivity| -165 dBM
Accuracy| < 3 m
Hot start| < 1 s
Warm start| < 25 s
Cold start| < 35 s
CELLULAR
Technology| GSM
2G bands| Quad-band 850 / 900 / 1800 / 1900 MHz
Data transfer| GPRS Multi-Slot Class 12 (up to 240 kbps)
Data support| SMS (text/data)
POWER
Input voltage range| 12 – 30 V DC with overvoltage protection
Back-up battery| 3.7 V 45 mAh
Power consumption| At 12V < 5 mA (Ultra Deep Sleep)
At 12V < 7 mA (Deep Sleep)
At 12V < 7 mA (Online Deep Sleep)
At 12V < 8 mA (GPS Sleep)
At 12V < 28 mA (nominal with no load)
Internal fuse| 3A, 125V
BLUETOOTH
Specification| 4.0 + LE
Supported peripherals| Temperature and Humidity sensor, Headset, Inateck Barcode Scanner, Universal BLE sensor support
OBD INTERFACE
Data| K-Line, CAN Bus data
Data reading| Up to 32 vehicle onboard parameters, 9 supported OBD protocols
INTERFACE
Connection| OBDII socket
GNSS antenna| Internal High Gain
GSM antenna| Internal High Gain
USB| 2.0 Micro-USB
LED indication| 2 status LED lights
SIM| Nano-SIM
Memory| 128MB internal flash memory
PHYSICAL SPECIFICATION
Dimensions| 52.6 x 29.1 x 26 mm (L x W x H)
OPERATING ENVIRONMENT
Operating temperature (without battery)| -40 °C to +85 °C
Storage temperature (without battery)| -40 °C to +85 °C
Operating humidity| 5% to 95% non-condensing
Ingress Protection Rating| IP41
Battery charge temperature| +10 °C to +45 °C
Battery discharge temperature| -20 °C to +60 °C
Battery storage temperature| -20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
FEATURES
Sensors| Accelerometer
Scenarios| Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip
Sleep modes| GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep
Configuration and firmware update| FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration)
SMS| Configuration, Events, Debug
GPRS commands| Configuration, Debug
Time Synchronization| GPS, NITZ, NTP
Fuel monitoring| OBDII
Ignition detection| Accelerometer, External Power Voltage, Engine RPM

Safety information

This message contains information on how to operate FMB002 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +12…+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
Before unmounting the device from vehicle, ignition MUST be OFF.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.

All wireless data transferring devices produce interference that may affect other devices which are placed nearby.

Please consult representatives of your vehicle model regarding OBDII location on your vehicle. In case you are not sure about proper connection, please consult qualified personnel.

The programming must be performed using a PC with autonomic power supply.

Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity.

Teltonika is not responsible for any harm caused by wrong cables used for connection between PC and FMB002

WARNING! Do not use FMB002 device if it distracts driver or causes inconvenience due to OBDII placement. Device must not interfere with driver.

Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

Certification and Approvals

FMB002 CE / RED
FMB002 E-Mark
FMB002 EAC
FMB002 RoHS
FMB002 REACH
FMB002 Declaration of IMEI assignment
FMB002 Declaration of device operation temperature

This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in ourWiki.

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.

Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).

Warranty

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.

Contact us teltonika.lt/company/contacts

All batteries carry a reduced 6 month warranty period.

If a product should fail within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
TELTONIKA can also repair products that are out of warranty at an agreed cost.

Warranty Disclaimer

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.

More information can be found at teltonika.lt/warranty- repair