Fanvil I32V Video Door Phone Installation Guide

: June 6, 2024
: Fanvil

Video Door Phone

Quick Installation Guide

Fanvil I32V Video Door Phone 2

www.fanvil.com

(1) Package Contents

i32V Video Door Phone Connector
Quick Installation Guide Mounting Template
RFID Cards Screw and tool

(2) Physical specification

Device size	195 x 120 x 34 (mm)

1) Panel

$Fanvil I32V - 1\) Panel$

IR LED
RFID area
DSS Key
Camera
Speaker
MIC

2) Interface description

Open the rear case of the device, there is a row of terminal blocks for connecting the power supply, electric lock control, etc. The connection is as follows:

$Fanvil I32V - 2\) Interface description$

$Fanvil I32V - 2\) Interface description - 1$

Serial number	Description
1	Ethernet interface: standard RJ45 interface, 10/100M adaptive, it is

recommended to use five or five types of network cable
2| Power interface: 12V/1A input left positive, right grounded
3, 5| Two sets of short-circuit input detection interfaces: for connecting switches, infrared probes, door magnets, vibration sensors and other input devices
4, 6| Two sets of short-circuit output control interface: used to control electric locks, alarms, etc.
7| Wiegand interface
8, 9| Two sets of door magnetic detection
10| Recording output interface: Mix the device and the sound of the far- end call. One is the recording signal line, and the other is the ground line (be sure to ground the line, otherwise there will be noise)
11| External active speaker interface: external active speakers for audio power amplification. One is the audio signal line, and the other is the ground line (be sure to ground the line, otherwise there will be noise)
12| JP1 jumper

JP1 Jumper
There are two modes for power supply of electric-lock as shown in the picture below.
(The default is “ Passive Mode: ”).

Passive Mode: When the electric-lock starting current is more than 12V/500mA, need to use the external drive mode, the electric lock interface for short circuit output control.

Active Mode : When the electric-lock starting current is less than 12V/500mA, can use the internal drive mode, the electric lock interface is 12V DC output.

$Fanvil I32V - 2\) Interface description - 2$ $Fanvil I32V - 2\) Interface description - 3$ $Fanvil I32V - 2\) Interface description - 4$

3) Wiring instructions:

NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact

Driving Mode

|

Electric-lock Mode

| JP1 Jumper|

Connections

---|---|---|---
Active| Passive| No electricity when open| Electrify when open

√

| |

√

| | $Fanvil I32V - 2\) Interface description - 4$ |

√

| | |

√

| $Fanvil I32V - 2\) Interface description - 4$ |
|

√

|

√

| | $Fanvil I32V - 2\) Interface description - 3$ |
|

√

| |

√

| $Fanvil I32V - 2\) Interface description - 4$ | $Fanvil I32V - 3\) Wiring instructions - Connections 4$
|

√

|

√

| | $Fanvil I32V - 2\) Interface description - 3$ |

(3) Installation Diagram

Wall-mounted:

Use built-in screw tool to remove the surface shell;
Based installation dimensions, mounting hole in the wall to draw, use an electric drill holes lay;
The white rubber plugged into the wall and the bottom fixed with screws to the wall;
After connecting the power cord and network cable, screw the surface shell fixed.

(4) Searching Door Phone

There are two methods as shown below to search the device.

Method 1:

Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the IP address.
(Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe)

Fanvil I32V - Searching Door Phone

Method 2:

Long press DSS key for 10 seconds(after power-on for 30 seconds), and when the speaker beeps rapidly, press DSS key again quickly, the beeps stop, the intercom will report the IP address by itself.

In addition, device provides the device surface DSS key operation to switch IP address acquisition mode:
Long press the DSS key for 10 seconds, to be issued by the speaker Beep, and then press the DSS key three times, the beep stops. Wait 10 seconds, after the success of the system automatically broadcast the current IP address.

(5) IP Door Phone Setting

Step 1: Log in the door phone

Input IP address (e.g. http://192.168.1.128) into address bar of PC’s web browser.
The default user name and password are both admin.

Fanvil I32V - IP Door Phone Setting - Step 1

Step 2: Add the SIP account.

Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.

Fanvil I32V - IP Door Phone Setting - Step 2

Step 3: Setting DSS key

Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Hot Key
Number 1 : The DSS Key will dial to this Number 1.
Number 2 : If Number 1 is unavailable, it will be forwarded to Number 2.
Line : Working line
Subtype : Speed dial

Fanvil I32V - IP Door Phone Setting - Step 3

Step 4: Door Phone Setting

Fanvil I32V - IP Door Phone Setting - Step 4

(6) Door Unlocking Setting

RFID Card

Step 1: Go to EGS Access → Enter the Name and ID Number (Only Front 10 yards) → Press Add to Access Table.
Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.

Fanvil I32V - Door Unlocking Setting - RFID Card

Remote Password

Step 1: Go to EGS Setting → Features → Set Remote Password (The default is “”).
Step 2: To answer the call made by visitor via SIP phone, press the “” key to unlock the door the visitor.

Fanvil I32V - Door Unlocking Setting - Remote Password