Fanvil i31S Video Door Phone Installation Guide

June 6, 2024
Fanvil

Fanvil i31S Video Door Phone Installation Guide

Fanvil i31S Video Door Phone

Package Contents

  • Door Phone

  • Connectors

  • Quick Installation Guide

  • Mounting Temlate

  • RFIC Cards

  • Screw and Wrench

Physical Specifications

Device size|

223 x 130 x 74mm

---|---
Weight|

1800g

Front Panel
Product Overview

Interface|

Description

---|---
Camera|

Get the video.

Infrared light & Photoresistor|

The Compensate for lack of ambient light

Speaker

|

The door phone has a built-in speaker for convenient communication and alert use.

MIC

|

The door phone has a built-in microphone hidden in the pinhole located on the front panel

RFID Reader|

Use RFID cards to unlock the door by touching RFID reader of device.

Button Definition

Button Description

DSS Key

|

Press the Button, calling or request to open the door.

Numeric Keyboard

|

Input password to open the door or call.

LED Definition

LED

|

Status

|

Description

---|---|---
Lock Icon

Lock

|

Steady Blue

|

Door unlocking

off

|

Door locking


Call

|

Blinks per second

|

Hold

Steady Blue

|

Call Hold

off

|

On Hook


Ring

|

Steady Blue

|

Ringing

off

|

On Hook


Network & SIP Registration

|

Blinks per second

| Network error

off

|

Network is normal, SIP is not registered

Blinks every 3 seconds

|

SIP Registration failed

Steady Blue

|

SIP Registration succeeded

**Port Definition**

After removing the Back Panel of device, there are one terminal block connectors for power and lock control connection as shown in the picture below.
Port Definition

Network Connector
Network Connector

Power and Electric-lock Connector****

Power and Electric-lock Connector****

1

| 2| 3| 4|

5

|

6

|

7

---|---|---|---|---|---|---

+DC12V

| VSS| NC| COM|

NO

|

S-IN

|

S-OUT

12V DC Input

|

Electric-lock switch

|

Indoor switch

JP1 Jumper
There are two modes for power supply of electric-lock as shown in the picture below.
(The default is “Passive Mode ”).

Passive Mode:
When the electric-lock starting current is more than 12V/500mA, need to use the external
drive mode, the electric lock interface for short circuit output control.

Active Mode :
When the electric-lock starting current is less than 12V/500mA, can use the internal drive mode, the electric lock interface is 12V DC output.

    • Jumper in passive mode
  • Jumper in active mode

Wiring instructions
NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact

Driving Mode

|

Electric-lock Mode

|

JP1

Jumper

|

Connections

---|---|---|---

Active

|

Passive

|

No electricity when open

|

Electrify when open

| |

| |

|

| | |

|

|
|

|

| |

|
|

| |

|

|
|

|

| |

|

Installation

  • **Front

**

  • **Panel Main Part of Intercom

**

  • **Rain Shade

**

  • Back Panel
    Wiring Instructions

Figure 1 Three Major Parts of i31S

Step 1: Installation preparation

  • Check the following contents:
    1. Hex wrench x 1
    2. RJ45 plugs x 2 (1 spare)
    3. TA5 x 40mm screws x 4
    4. 35mm screw anchors x4
  •  Tools that may be required:
    1. Hex wrench
    2. Phillips screwdriver (Ph2 or Ph3), hammer, RJ45 crimper
    3. Electric impact drill with an 6mm drill bit

**Step 2: Drilling

**

Figure 2 Wall Mounting

  • Place the mounting template with dimensions on the surface of a wall in a desired flat position.
  • Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 50mm deep. Remove the template when finishing drilling.
  • Push or hammer screw anchors into the drilled holes.

Step 3: Removing hanging shell

  • With L-shaped screwdriver, unpack the front panel as diagram (3) (Counter- lockwise) and (4)
    Figure 3
    Figure 4

  • After taking off the 6 conductive sponges in the plastic shell, use the cross screwdriver to remove the 6 screws on the plastic shell and remove the rain cover from the plastic shell. Then separate the plastic shell from the rear shell as diagram (5).
    Removing hanging shell

Figure 5

Step 4: Back panel fixing and cabling
Back panel fixing and cabling
Figure 6

Back panel fixing and cabling
Figure 7

  • Select the hole for cable supply, 15cm to 20cm cable length is recommended. Note: The direction of the cable hole on back panel is pointing down.
  • With 4 TA5*40mm screws, tighten the back panel on the wall as diagram (6).
  • Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors description (refer to Section 2).
  • Test whether there is electricity by doing the following:
    Press the # button for 3 seconds to get the IP address of intercom by voice. Input access password or press the indoor switch to check electric-lock installation.
    Note : Do not proceed mounting until you have finished the electric checking.

Step 4: Mounting
Mounting

Figure 8
Mounting

Figure 9

After locking the 6 screws into the corresponding position of the plastic housing, the 6 conductive sponges is loaded into a screw hole. As shown in Fig. 8, the rear shell is locked
Note: This sponge can enhance the ESD protection function of the product. Kindly suggest that it should not be ignored!

Push the front panel into the plastic frame, and tighten it with 6 screws as diagram (9)
Note: Make sure the screws have been tightened properly for better waterproof effect.

Searching Door Phone

There are two methods as shown below to search the device.

Method 1:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the IP address.
Searching Door Phone

Method 2:
Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice.
In addition device provides the device surface DSS key operation to switch IP address acquisition mode: long press the DSS key for 10 seconds, to be issued by the speaker Beep, and then press the DSS key three times, the beep stops. Wait 10 seconds, after the success of the system automatically broadcast the current IP address.
Searching Door Phone

Default Setting


Default DHCP Client

| Enable

Static IP Address

|

192.168.1.128

Default Web Port

|

80

Default Login User Name

|

admin

Default Login Password

|

admin

Display IP address

|

Hold # for 3 seconds to display by voice

Search Tools

|

iDoorPhone Network Scanner

SIP Door Phone Setting

Step 1: Log in the door phone
Input IP address (e.g. http://192.168.1.149) into address bar of PC’s web browser.
The default user name and password are both admin.
Log in the door phone

Step 2: Add the SIP account.
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.
Add the SIP account

Step 3: Setting DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Hot Key
Number 1: The DSS Key will dial to this Number 1.
Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
Line: Working line
Subtype: Speed dial
Setting DSS key

Step 4: Door Phone Setting
Door Phone Setting

Door Unlocking Setting

Local

  1. Local Password
    Step 1 : Go to EGS Setting ї Features ї Set Local Password (The default is “6789”).
    Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
    Local Password

  2. Private Access Code
    Step 1:
    Go to EGS Access ї Access Rule ї set Access Code.
    Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
    Private Access Code

Remote
Remote Password
Step 1: Go to EGS Setting ї Features ї Set Remote Password (The default is “”).
Step 2: To answer the call made by visitor via SIP phone, press the “
” key to unlock the door the visitor.
Remote

RFID Card
Step 1: Go to EGS Access ї Enter the Name and ID Number (Only Front 10 yards) ї Press Add to Access Table.
Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.
RFID Card

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals