MONSTER MLB7-1043 Indoor/Outdoor Rechargeable Multi-Color LED Mini ORB with IR Control User Manual
- June 6, 2024
- Monster
Table of Contents
MONSTER MLB7-1043 Indoor/Outdoor Rechargeable Multi-Color LED Mini ORB with
IR Control User Manual
Introduction
This Indoor/Outdoor Rechargeable Multi-Color LED Mini Orb is portable, easy to use, and is ideal for adding controllable ambient lighting to any space indoors or out.
Features
- Water-resistant LED Mini Orb is great for both indoor and outdoor and use
- Integrated rechargeable battery provides over 4hrs of light (time varies by lighting color/mode)
- Sleek, stylish design accents any décor
- Multi-color and dimmable LED lighting effects with Flashing and Fading color-changing modes
- Remote control works up to 26ft/8m away
- Charge from any USB power source (not included)
What’s Included
- Indoor/Outdoor Rechargeable Multi-Color LED Mini Orb
- IR Remote Control with battery
- USB Charging Cable
- User Manual x1 pc
Safety Instructions
Please read and understand all instructions before using this product. If damage is caused by failure to follow the instructions, this warranty is null and void.
- Keep these instructions.
- Do not drop, puncture, or disassemble this product.
- For water-resistance, keep the silicon USB cover tightly sealed.
- Avoid long exposure to direct sunlight, which may cause damage.
- Do not expose this product to open flames.
- Do not use the product in a strong magnetic field.
- Use a clean, soft cloth to clean. Do not use any corrosive cleaners/oils to clean.
- Do not attempt to repair the device or open the unit as this will void the warranty
Get Started/ Charging
The LED Mini Orb has a built-in rechargeable battery that can be charged using the included micro USB to USB Type-A cable and any 5v USB power source (not included). For best results, charge before use.
- Open the USB cover and insert the charging cable
- While charging, the LED will glow Red When charging is complete, the LED will turn OFF
- To keep water-resistant, keep the USB cover closed securely when not charging
NOTE: Under normal operation, the Orb will provide over 4.5hrs of light. Solid colors, lower brightness, and fewer adjustments can extend the battery life considerably
Folding Handle/Hanging Loop
The LED Mini Orb features a fold-out ring on the bottom that can be used to carry or hang the product, allowing you to use it in more ways and more locations.
- Do not hang the Mini Orb by the USB charging cable.
- Fold away the handle/hanging loop when not in use.
- Do not drop this product.
Specifications
- LED Mini Orb Input (USB): 5V 0.5A
- Battery Life: 4.5hrs
- Charge Time: 2.5hrs
- Standby Time: 400hrs
- USB Charging Cable Length: 3ft
- Remote Control: 3V (1 x 3V battery, type CR2025)
Controls, at a Glance
IR Remote
LED Mini Orb (bottom)
1
|
ON
|
Turn the product on
---|---|---
2
|
OFF
|
Turn the product off
3
|
COLOR SELECTORS
|
Change the color to match your mood
4
|
WHITE
|
Change the color to white
5|
FADE
|
Fade color-changing mode
6|
FLASH
|
Flash color-changing mode
7
|
RESET
|
Reset to default settings
8|
DIMMER BUTTONS
|
Adjust the brightness/intensity
Button Operation
- Turn on the LED Mini Orb by pressing the Power/Mode button on the bottom of the device (it will turn on into the last used lighting mode)
- Continuously pressing the Mode button will cycle through the following lighting modes:
- FLASH: quickly flashes through the color spectrum
- FADE: smoothly flows through the color spectrum
- RED: solid color
- GREEN: solid color
- BLUE: solid color
- WHITE: solid color
- STANDBY: LEDs are off, IR sensor remains active
- At any time, press and hold the Power/Mode button to turn OFF the LED Mini Orb
Standby Mode
Note: The Mini Orb can only respond to the remote control if it is ON or in STANDBY mode.
In STANDBY mode the LEDs will be off but the IR sensor will remain active so that the Mini Orb can respond to the IR remote. If the Mini Orb is turned OFF it must first be reactivated manually before the remote will work.
Note: If left in Standby Mode for an extended period of time, the battery may become depleted and you may need to charge the device.
IR Remote Operation
Note: The Mini Orb can only respond to the remote control if it is ON or in STANDBY mode.
- Turn on the LED Light by pushing the ON button on the remote control
- Select the desired color of the desired effect by pushing the corresponding button on the remote control
- Set the desired brightness using the buttons to increase/decrease the intensity of color
- Push the OFF button to turn off the LED Light
Changing the remote control battery:
The battery for the remote control has already been installed. Remove the battery pull tab to operate.
- The battery compartment is located on the narrow side of the remote control
- Remove the empty battery and insert a 3V battery, type CR2025, with the positive terminal pointing upwards
- Place the battery compartment back in the remote control so it locks in place
Customer Service
1 Year Limited Warranty
customerservice@monsterilluminessence.com
In the event this product becomes defective, please do not return this product to your retailer.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s warranty or authority to operate the equipment.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed or mobile condition. The minimum separation distance is 20cm. The illustrated products and specifications may differ slightly from those supplied. The M Monster logo is a registered trademark of Monster, Inc. or its subsidiaries in the U.S. and other countries and are used under license. All other brand names are trademarks of their respective owners. Neither Jem Accessories, Inc. nor Monster, Inc.is affiliated with the respective owners of their trademarks. Licensed and Manufactured by Jem Accessories, Inc. South Plainfield, NJ 07080.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>