FEIT Smart WiFi LED Shop Light Instruction Manual
- June 6, 2024
- Feit
Table of Contents
MODEL SHOP/4/HO/CCT/AG
IMPORTANT , RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
SMART WIFI LED SHOP LIGHT INSTALLATION INSTRUCTIONS
WARNING: These products may represent a possible shocker fire hazard if
Impropedy Installed Of aladX4111 any. Products should be Installed In
accordance with the owner’s mama current electrical codes ancUomhe current
National Electsk Code (NMC).
PARTS INCLUDED (Drawings not to scale)
THIS FIXTURE IS INTENDED TO ONLY BE INSTALLED DIRECTLY BENEATH A CEILING-
MOUNTED RECEPTACLE.
CAUTION: Installation not be made on a radiant-heating ceiling.
CAUTION: Hooks are to engage the chain only and not the electric cord.
CAUTION: This fixture needs to be grounded.
Voltage: 120Vac Current: X.XXA
SUITABLE FOR DAMP LOCATIONS
LINKING MULTIPLE SHOPLIGHTS
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help. Any changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials
for up to five years from the date of purchase. If the product fails within
the warranty period, please contact Feit Electric at
info@feit.com, visit feit.com/contact-
us or call 1-866-326-BULB (2852) for instructions
on replacement or refund.
REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY
EXPRESSLY EXCLUDED.
Some states and provinces do not allow the exclusion of incidental or
consequential damages, so the above limitation or exclusion may not apply to
you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state or province to province.
For comments please contact:
Feit Electric Customer Service Department 4901 Gregg Road, Pico Rivera, CA
90660
REV007
FEIT ELECTRIC COMPANY
PICO RIVERA, CA
1-866-326-BULB (2852)
FAX 562-908-6360
www.feit.com
WARNING:
TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE
IN ORDER TO PREVENT POSSIBLE ELECTRIC SHOCK.
INSTALLATION OPTIONS
Install fixture using included chain and V-hooks
- Install provided screw-hooks directly onto the ceiling. Spacing between screws should be 28 inches (See Figure A). For concrete ceilings/drywalls, wall anchors are required. Drill two holes (use a 1/4 inch drill bit) for provided wall anchors then use provided screw hooks (See Figure 1).
- Attach the chain to V-hooks then insert hooks into mounting holes located on the endcap of the fixture (See Figure 2). Do this for both ends of the fixture.
- Install fixture to the ceiling by hanging the chain to pre-mounted screw-hooks on the ceiling (See Figure 3).
- Plugin power-cord to an outlet or connect to additional SHOP/4/HO/CCT/AG Shop Lights.
- Zip tie cord to chain so that excess cord is kept out of the workspace. (see Figure 4).
| 
Install fixture flush mount using screws
- Install provided screws directly onto the mounting surface. Spacing between screws should be 45.71 inches. Gap (D) should be .079-.099 inches. For concrete/drywall surfaces, wall anchors are required. Drill two holes (use a 1/4 inch drill bit) for provided wall anchors then use provided screws (See Figure 5).
- Install fixture to the mounting surface by inserting the Key Holes on the top side of the fixture into the mounting screws (See Figure 6). It may be necessary to adjust the tightness of the screws (Gap D). Make sure both screws hold the fixture securely on the narrow side of the Key Holes.
- Mount a third screw next to the side of the outlet (See Figure 7). If the anchor is required, mark the hole as close as possible to the fixture, remove the fixture, drill the hole on the marked position, install anchor into the drilled hole, re-install the fixture then install the screw into the wall anchor. This will secure the fixture into place.
- Plugin power-cord to an outlet or connect to additional SHOP/4/HO/CCT/AG Shop Lights.
Install fixture flush mount using screws
- Install provided screws directly onto the mounting surface. Spacing between screws should be 45.71 inches. Gap (D) should be .079-.099 inches. For concrete/drywall surfaces, wall anchors are required. Drill two holes (use a 1/4 inch drill bit) for provided wall anchors then use provided screws (See Figure 5).
- Install fixture to the mounting surface by inserting the Key Holes on the top side of the fixture into the mounting screws (See Figure 6). It may be necessary to adjust the tightness of the screws (Gap D). Make sure both screws hold the fixture securely on the narrow side of the Key Holes.
- Mount a third screw next to the side of the outlet (See Figure 7). If the anchor is required, mark the hole as close as possible to the fixture, remove the fixture, drill the hole on the marked position, install anchor into the drilled hole, re-install the fixture then install the screw into the wall anchor. This will secure the fixture into place.
- Plugin power-cord to an outlet or connect to additional SHOP/4/HO/CCT/AG Shop Lights.
Drawings not to scale
Fixture Maintenance
- Please make sure the power is Off before maintenance.
- To avoid any damage to the product, please do not use any chemical solvents during routine maintenance.
- To ensure better lighting, please clean the fixture regularly.
SAVE THESE INSTRUCTIONS
Smart Wi-Fi Shop Light
Quick Install APP Guide
Getting Started:
-
Download the Feit Electric app on your smart device
-
Plugin your Smart Wi-Fi Shop Light
Plug the Smart Wi-Fi Shop Light into any indoor receptacle.
WARNING:
These products may represent a possible shock or fire hazard if improperly
installed or attached in any way. Products should be installed in accordance
with this install guide, current electrical codes, and/or the current National
Electric Code (NEC).
NOTE: If the Shop Light(s) is not blinking, turn the Shop Light(s) ON- OFF-ON-OFF-ON by using the plug, wall switch, or slide switch (on the Shop Light). Constant power to the Shop Light(s) is required at all times. -
Launch and use the Feit Electric app to complete the setup
Tap Add Device or the + sign, then select Lighting Device and confirm. You will be prompted to enter your Wi-Fi network and password.
Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.
-
(Optional) Connect to Google Assistant or Alexa using the in-App guide
TROUBLESHOOTING TIPS
If you are having difficulty connecting:
- Make sure the Wi-Fi network is a 2.4 GHz network. Smart Wi-Fi Shop Light will not connect to a 5 GHz network.
- Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.
- The Wi-Fi connection may not have good coverage during setup. Try moving the Smart Wi-Fi Shop Light closer to your Wi-Fi router.
- Your Wi-Fi network password is case sensitive, make sure you are entering correctly.
Please also check the App User Guide for more information
Need Help?
FAQs and the latest versions of user guides can be found at
feit.com/help and
feit.com/smart.
To reach customer support please visit feit.com/contact-us
SAVE THESE INSTRUCTIONS
REV007
FEIT ELECTRIC COMPANY
PICO RIVERA, CA
1-866-326-BULB (2852)
FAX 562-908-6360
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>