Roxcore Avenue Silence User Manual
- June 6, 2024
- Roxcore
Table of Contents
Avenue Silence
man ual
Overview
-
- Bluetooth
- –
- Status LED
- Charging Port
- Microphone
- NC
- AIX in
- NC LCD
Specifications
Bluetooth version: 40
Impedant: 320
Sensitivity: 1053 dB
Listening frequency: 20 Hz – 20 kHz
Cancellation frequency: 0 Hz – 500 Hz
Cancellation: 20 dB
Charging input: 5V, 220 mA
Charge time: 3h
Battery time: Up to 16 h (12 with NC active)
Charging cable: Micro USB
Charging cable length: 100 cm
Audio cable length: 125 cm
Weight: 238g
Frequency Range: 2402MHz-2480 MHz
Effective Radiated Power: 3.78 dBm
Use
Power on/off
To turn on the headphones, press and hold the Bluetooth button (2) until the
Status LED (4) blinks blue. Press and hold the Bluetooth button again until
the Status LED blinks red. The headphones are now turned off. To start the
noise cancellation, slide the NC button (7) up. The NC LED (9) will light up
in green. To turn off the noise cancellation, slide the NC button down. The NC
LED will turn off.
Charging
Connect the USB cable to the charging port (5) and a computer or a USB power
adapter. The LED will shine red during charging and turn blue when the battery
is fully charged. The LED will flash red if the battery level is low. Note:
The headphones will reset when connected to a charging source.
Pairing
Make sure the headphones are turned off. Press and hold the Bluetooth button
(2) for 5 seconds to enter pairing mode. The Status LED (4) will blink blue
and red. Turn on bluetooth on your device and search for “Avenue
Silence”(90300) or “Roxcore ANC”(97900), select it when found. If necessary,
enter the passcode, “0000”, to pair and connect the headphones. Some devices
also ask to confirm the headset connection after pairing. The Status LED will
blink blue and a voice will say “connected” after the pairing is successful.
If no bluetooth devices are paired within 15 minutes the headphones will turn
off.
General functions
Change the volume with the + & – buttons (1 & 3). You can also skip to the
next track or go to the previous by holding in the corresponding button. Play
or pause the current track by pressing the Bluetooth button (2). To answer or
end a call, press the bluetooth button. Press and hold it for at least 2
seconds to reject an incoming call. Doubleclick it to redial the last call.
Note: The functions of the buttons may not always be the same for all
devices and brands.
Multifunction button
There is a multifunction button on the included 3.5 mm audio cable. You can
use this to answer incoming calls or manage music. Make sure the headphones
are turned off before connecting the cable. Connect the end with the headphone
symbol to the headphones and the other end to your device. During an incoming
call press it once to answer or press and hold for 2 seconds to reject the
call. Press it once during an ongoing call to hang up. When playing music
press once to play or pause a track, dou bleclick to go forward to the next
track. Tripleclick to go to the start of a track or jump two tracks forward
depending on phone model. There is also a microphone situated near the
multifunction button that can be used during phone calls.
Note: You must turn the headphones off and on before connecting the cable
if the bluetooth mode has been activated. The functions of the button may not
always be the same for all devices and brands. If the battery is depleted the
noise cancellation must be turned off if you want to use the 3.5 mm audio
cable.
Note! This product contains a rechargeable Li-ion battery and the battery can not be replaced. To prevent possible hearing damage, do not listen at high volume levels for long periods. If you encounter any problems with the manual, please go to www.kjell.com/97900, 90300 for an updated version.
Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
Full text of the EU declaration of conformity is available at
www.kjell.com/97900, 90300