DYNATRAP DT160 Insect Trap Owner’s Manual

: June 6, 2024
: DynaTrap

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION & OPERATING INSTRUCTIONS
FCC COMPLIANCE
USER MAINTENANCE INSTRUCTIONS – CLEANING
REPLACING BULB
REPLACEMENT PARTS
HOW THE DYNATRAP® INSECT TRAP WORKS
TROUBLESHOOTING
LIMITED WARRANTY
Documents / Resources

DYNATRAP DT160 Insect Trap

Thank you for purchasing the DynaTrap® Insect Trap!
This product may be covered by one or more U.S. patents or pending patent applications. See www.DynaTrap.com/patents

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT: READ CAREFULLY

SAVE THESE INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING: when using electric appliances, basic precautions should always be followed, including the following:

Please read all instructions before using the DynaTrap® Insect Trap and keep for future reference.
To disconnect, remove plug from outlet.
To reduce the risk of injury from moving parts or electric shock, disconnect plug before servicing or cleaning.
Always unplug before replacing lamp. Replace with same type rated 1.8-Watt UV-Light LED bulb, DynaTrap® model 11020.
Do not position the unit near heat, gas, oil or other flammable materials.
Place out of reach from children.
To reduce the risk of electrical shock, do not put appliance in water or other liquid.
Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has been dropped into water or other liquid.
Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).
Do not insert fingers or any foreign objects into the unit while it is connected to an electrical outlet.
Collected insects within the unit may contribute to fire, so clean insects from the unit frequently.
Do not clean this product with water spray. Do not place where it can fall into water, or near flammable materials.
Do not touch fan while in motion.
Do not abuse cord–never carry or hang unit by cord or yank it to disconnect from receptacle. Keep cord away from sharp edges.
If using outdoors, use only extension cords with a tag stating, “Suitable for Use with Outdoor Appliances.”
Use only extension cords that have plug and receptacles that match the product plug. Replace or repair damaged cords.
Only use attachments recommended or sold by the manufacturer.
This appliance is provided with double insulation. Use only identical replacement parts. See instructions for Servicing of Double- Insulated Appliances.

INSTALLATION & OPERATING INSTRUCTIONS

Unpack unit. Save carton for off-season storage (if needed).
The unit will turn on automatically when plugged in. For best catch results, leave the trap on and running, 24/7.
Catch rate activity will be higher at night. For best catch results it is recommended to keep the unit away from competing light sources.
It is recommended to place the unit at least 20 to 40 feet away from where people will be sitting.
This unit is all-weather resistant – designed for outdoor use including rainy conditions.
SERVICING OF DOUBLE-INSULATED APPLIANCES – In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing of a double-insulated appliance requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to those parts in the appliance. The symbol must be identical to those parts in the appliance. A double-insulated appliance is marked with the words “DOUBLE INSULATION”, “DOUBLE-INSULATED” or the symbol:
The electrical adapter provided with this product is equipped with a 2-conductor cord and a 2-prong plug as a safety feature. If the plug does not fully fit in the outlet, contact a qualified electrician. To reduce the risk of electrical shock, only plug into a properly installed outlet. Do not attempt to defeat this safety feature.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

USER MAINTENANCE INSTRUCTIONS – CLEANING

Frequent cleaning will prolong the life of the unit, ensure fire prevention and provide for more efficient operation.

Be sure to clean the unit at least once per week.
Unplug the unit.
For weekly cleaning, twist the cage clockwise, and remove the damper by grasping the crossbar near the edge of the damper. Pull up firmly. Remove any buildup from the inside of the retaining cage and fan with a brush. Replace damper, snap firmly into place.
When replacing the retaining cage DO NOT press/push against the screen windows.
Clean prior to off-season storage.

REPLACING BULB

– Replace With DynaTrap UV-LIGHT LED Bulb #11020 (or equivalent G24-Q2 Type – DC 9V/1.8 W UVA Bulb) The UV-LIGHT LED light bulb life expectancy is approximately 20,000 hours (or about 2.25 years).

UNPLUG UNIT, and allow bulb to cool before replacing.
Remove screw (A) under cover, twist counter-clockwise and remove.
Grasp lamp housing and twist to remove (B). Note: Lamp housing and lower sections will remain connected by electrical wire – Do Not Pull or Attempt To Disconnect.
Cover the bulb (C) with a cloth to protect your fingers and hand. Grasp the bulb (with your hand and fingers protected by the cloth) and gently pull the bulb from the socket.
Remove any debris from the lamp socket with a brush. Replace new bulb by aligning mark on base of bulb (D), with corresponding mark on socket (E) to assure proper alignment. Replace lamp housing and twist to secure (C).
Replace cover and secure with screw **(A).

**

REPLACEMENT PARTS

11020 1, UV-LIGHT LED Replacement Bulb, G24-Q2 Type – DC 9V/1.8W

To see all replacement and accessory parts available for your DynaTrap, visitwww.DynaTrap.com.

HOW THE DYNATRAP® INSECT TRAP WORKS

Flying insects are attracted to the unit by UV light and CO2 that is generated by the photo-catalysis between the UV-LIGHT LED lamp and special TiO2 coating. The fan then pulls the insects into the screened base, trapping them until they dehydrate and die. The base can be removed, allowing the contents to be periodically emptied into the trash.

TROUBLESHOOTING

Problem:	Possible cause:	Correction:
Bulb does not illuminate and fan does not spin.	No electrical power.

Check plug, receptacle and fuse or circuit breaker.

Bulb illuminates, but fan does not spin.| Shorted fan.| UNPLUG UNIT: Examine fan to see that it is free from foreign material, dirt or buildup of dead insects.
Clean unit as in “CLEANING” section.
Fan spins, but bulb does not illuminate.|

Bulb not seated properly
Burnt out bulb

|

Check socket for proper bulb seating and alignment.
Replace bulb following instructions under “Replacing Bulb”

LIMITED WARRANTY

DYNAMIC guarantees to the original purchaser that this product is free from defective materials and workmanship. This warranty is limited to remedy any defective part for a period of one year from date of original date of purchase. Retain your original receipt as proof of purchase. This warranty does not apply to the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been altered, no warranty is in force. This warranty does not apply if this unit is purchased outside the United States, excluding Canada and Mexico. In no case shall DYNAMIC be liable for any accidental, punitive, consequential, or any other damages of any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

SAVE THESE INSTRUCTIONS

Dynamic Solutions Worldwide, LLC
69 N. Locust St., Lititz, PA 17543
1-877-403-8727 (TRAP)
dynatrap@woodstream.freshdesk.com
www.DynaTrap.com

FOR HOUSEHOLD AND COMMERCIAL, INDOOR AND OUTDOOR USE

100 – 240 V~ 50/60 Hz 0.06 A max.