WORX WG607 Electric Pressure Washer Installation Guide

WG607

WARNING: This product can expose you to chemicals including lead and Di (2-ethylhexyl) phthalate (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

GENERAL SAFETY WARNINGS

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product basic precautions should always be followed, including the following:

1. Read all the instructions before using the product.
2. To reduce the risk of injury, close supervision is necessary when a product is used near children.
3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.
4. Stay alert – Watch what you are doing.
5. Do not operate the product when fatigued or under the influence of alcohol or drugs.
6. Keep operating area clear of all persons.
7. Do not overreach or stand on unstable support. Keep good footing and balance at all times.
8. Follow the maintenance instructions specified in the manual.
9. This Product Is Provided With A Ground Fault Circuit Interrupter Built Into The Power Cord or Plug. If Replacement Of The Ground Fault Circuit Interrupter Or Cord Is Needed, Use Only Identical Replacement Parts.
10. WARNING – Risk of eye injury. Spray can splashback or propel objects. Always wear properly rated eye protection such as safety goggles or face shields while spraying. (Safety glasses do not provide full protection.)

SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least

resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a ground pin. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING – Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter with this product.

GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug or the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the ground-fault circuit-interrupter or cord become necessary, use only identical replacement parts.

EXTENSION CORDS

**WARNING:** Inadequate extension cords can be dangerous. If the appliance cord is equipped with a GFCI, do not use extension cords. If the appliance cord is not equipped with a GFCI, the appliance and any extension cord used should be connected only to a GFCI-protected power source.

1. Use only extension cords that have grounding-type plugs and female cord connectors that accept the plug from the product.
2. Use only extension cords that are intended for outdoor use. These extension cords are identified on the packaging or on the cord by a marking “Accept- able for use with outdoor appliances; store indoors while not in use.”
3. Use only extension cords having an electrical rating not less than the rating of the product.
4. Do not use a damaged extension cord. Examine ex tension cord before using and replace if damaged.
5. Do not abuse extension cord and do not yank on a cord to disconnect.
6. Keep cord away from heat and sharp edges.
7. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.
   WARNING – To reduce the risk of electrocution, use only a GFCI-protected extension cord or plug into GFCI outlet. Keep all connections dry and off the ground.
   Do not touch plug with wet hands.

Electric Pressure Washer

ADDITIONAL SAFETY WARNINGS

1. The electric supply connection shall be made by a qualified electrician and comply with IEC 60364-1. It is recommended that the electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device that will prove the earth circuit.
2. WARNING : This appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance.
3. WARNING : Do not use the appliance within range of persons unless they wear protective clothing.
4. WARNING : High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment or the appliance itself.
5. Do not direct the jet against yourself or others in order to clean clothes or footwear.
6. Disconnect from the electrical power supply before carrying out user maintenance.
7. High-pressure cleaners shall not be used by children or untrained personnel.
8. To ensure appliance safety, use only original spare parts from the manufacturer or approved by the manufacturer.
9. WARNING : High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.
10. Do not use the appliance if a supply cord or important parts of the appliance are damaged, e.g. safety devices, high pressure hoses, trigger gun.
11. Water that has flown through backflow preventers is considered to be non-potable.

SYMBOLS

| Read the manual
---|---
| Before any work on the machine itself,
pull the mains plug from the socket
outlet.
| Warning
| WARNING: Do not direct the jet at
persons, animals and electrical equipment.
| Protective earth
| Lock
| Unlock

COMPONENT LIST

• Not all the accessories illustrated or described are included in standard delivery.

Electric Pressure Washer

TECHNICAL DATA

| WG607
---|---
Rated current| 13 A
Rated pressure| 2000 psi (138  bar)
Rated water flow rate| 1.2 gpm
Soap tank capacity| 0.5 Gal (1.9 L)
Power cord length| 35 ft (10.5 m)
Machinery weight| 41.2 lbs (18.7 kg)
Max water temperature|  104 °F (40°C)
Maximum inlet pressure| 80 psi (0.55 MPa)
Protection class| I

ACCESSORIES

| WG607
---|---
Nozzle (25° / 40° / soap )| 3
Turbo Nozzle| 1
25ft Hose| 1
Declogging needle| 1

We recommend that you purchase your accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store
personnel can assist you and offer advice.

OPERATING INSTRUCTIONS NOTE:

Note: Before using the tool, read the instruction book carefully. INTENDED USE The electric high pressure washer is intended for residential cleaning projects-from porch to patio, driveways and decks, boats, pavers, bricks, BBQs and more.

ASSEMBLY & OPERATION

Cart Handle assembly
NOTE: when you hear “click ”,it  means that the handle has been assembled successfully.| See Fig. A
Attaching the lance
NOTE: Hold the lance with one hand and rotate the clamping lever until it is tightened.| See Fig. B
Screwing & Unscrewing the high-pressure hose
NOTE: Make sure the hose is tightly connected.
NOTE: For convenience of unscrewing the hose, please pull the trigger to drain water from wand when operation is completed and on/off switch is in “O” position.| See Fig. C1, C2, C3, C4
Attaching the garden hose
Connect one end of the home garden hose (not supplied) to the connector and another end to the waterspout.| See Fig. D
OPERATION| See Fig. E
Extension cord
It is not recommended to use the extension cord. If necessary, ensure the plug and extension cord connection is on an elevated surface that does not contact the water area.| See Fig. F
GFCI plug test
Press “test”, the light will be out.
Press “reset”, the power regains and the light will illuminate.
NOTE: To keep good operation of GFCI, please implement it once a month.| See Fig. G1,
Start/stop|
Turn on the water supply tap. Connect the washer to the power supply and turn the on/off switch to “I ” position.
Then press trigger.
NOTE: Before pressing trigger, push the lock-out down into the trigger.
WARNING: Do not start the machine without connecting and turning on the water supply because it may cause damage to high-pressure seals and reduce the service life of pump.| See Fig. G1G2

Electric Pressure Washer

Release the trigger and turn the on/off switch to “O” position. Turn Off  the water supply tap.
NOTE: When not in use, push the lock-out up until it clicks into the slot.| See Fig. H1H2
---|---
Select the right nozzles
Select the suitable nozzle for different cleaning jobs.
Nozzle 25 0 (green) is applicable for cleaning on concrete, bricks and masonry.
Nozzle 40 O (white) is applicable for cleaning on wooden and other soft objects.
The soap nozzle is applicable for soaping while other nozzles cannot be used to do it.
Turbo nozzle is applicable for cleaning on concrete, bricks and masonry.
**WARNING: Do not change the nozzle pattern when the tool is powered on.| See Fig. I
Cleaning
Begin with the nozzle 1-2ft away from the surface and approach with caution until it reaches the desired position for overly close spray may do harm to surface.
WARNING: Do not connect the machine to water supplies that are dirty, rusty, muddy, or corrosive. (Including window cleaning liquids, plant foods, or fertilizers etc.)| See Fig. J
Add and use detergent Install the soap nozzle before opera- tion. The detergent will automatically be drawn through the wand when the soap nozzle is being used.
NOTE: If necessary, use a funnel (not supplied)to prevent accidental overflows of detergent outside of the tank.| See Fig. K1, K2, K3
Use the hose reel
NOTE:** pull the Hose Reel Handle out and uncoil hose from the hose reel before use.| See Fig.L1, L2, L3
Using the power cord holder
To wind or unwind the power cord, pull out the power cord holders and then turn outwards or inwards.| See Fig. M1, M2

MAINTENANCE

Remove plug from the socket before carrying out any adjustment, servicing or maintenance.
Inspect the product for damaged or worn parts before each use. Do not operate it if you find damaged or worn parts. Contact your supplier or the manufacturer for replacement parts.

Power cord maintenance
If the electrical cord is damaged, do not attempt to repair yourself; call the Worx solutions center for further assistance.

Pump maintenance
Inspect the pump frequently whether any leaking occurs around the pump seal. If leaking occurs, please contact the solutions center for further assistance.

Nozzle maintenance
Remove the nozzle from the lance, then remove any possible obstructions using the included declogging needle (See Fig. N).Then use a garden hose to rinse the nozzle by backwashing.

STORAGE

1. Disconnect the water source. Turn on the pressure washer for a few seconds to assist with removing any remaining water. Then, quickly turn it off.
2. Unplug the power supply and wind power cord around the reel. (See Fig. M1)
3. Disconnect the high-pressure hose and garden hose (not supplied).
4. Tilt the unit to allow any remaining water to drain out of the pump, through the water inlet.
5. Store in a frost-free location with a temperature above 0°C(32°F). (See Fig. O)
   NOTE: Regular usage of a pump protector will prevent freeze damage and prolong the life of the pump. (See Fig. P1, P2)

Electric Pressure Washer

Symptom| Possible causes|

Solution

---|---|---
Machine does not start when the switch is in” 1″position.| Power cord is not plugged in.| Plug in power cord.
Socket is defective.| Check or replace plug, socket, fuses.
GFCI is triggered.| Press reset on GFCI plug.
Machine pressure is not consistent.| Pump is faulty.| Contact service center.
Air in line.| Remove the nozzle, turn on the machine and allow low pressure water to flow for a while and install the nozzle back.
Water inlet adapter is clogged or dirty.| Remove the adapter, rinse it with water and put is back.
The pressure of the pump is not adequate| Water supply is Insufficient.| Open water source completely.
Water supply is restricted.| Check If the water hose kinks or leaks.
Diameter of garden hose is too small.| Replace with right garden hose .
Leak or kink in hose .| Replace hose or untie kinks in hose.
No detergent| Wrong nozzle is attached| Attach the soap nozzle
Lance leaks| 0-ring needs to be replaced.| Replace 0-ring .If the problem is not solved ,contact service center to buy a new lance.

www.worx.com
Copyright © 2021, Positec. All Rights Reserved.
Copyright © 2021, Positec. Tous droits réservés.
© Derechos reservados 2021, Positec. Todos los derechos reservados.
AR01574200

References

• Web Server's Default Page
• P65Warnings.ca.gov
• P65Warnings.ca
• Lawn & Garden Equipment | Innovative Power Tools | WORX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>