WORX WX051 Pegasus Folding Work Table and Sawhorse User Manual

: June 2, 2024
: Worx

Table of Contents

SAFETY INSTRUCTIONS
SYMBOLS

WORX WX051 Pegasus Folding Work Table and Sawhorse a

PRODUCT SAFETY

SAFETY INSTRUCTIONS

WARNING: When using this product, always follow basic safety precautions. Failure to follow all instructions listed below may result in personal injury. Read all instructions before attempting to operate this product. Save these instructions for future reference.

Keep work area clear and well lit.
● Cluttered areas and benches invite injuries.
Make sure all moving parts are free from interference.
Ensure Pegasus is set up on firm, level ground and is stable.
Keep other people away.
● Do not let other people, especially children, not involved in the work touch the tool and keep them away from the work area.
Be aware of over-balancing. When a large piece is cut from one end of material supported by Pegasus, the remaining piece may be heavy enough to tip over. Always ensure the work piece is well supported.
Check that table latches are securely locked and legs are fully extended, with tray flat before operating Pegasus
The tool must be used only for its intended purpose. Any use other than those mentioned in these instructions will be considered a case of misuse.
The manufacturer shall not be liable for any damage or injury resulting from misuse.
Never stand on this product.
Dress properly
● Do not wear loose clothing or jewelry, which can be caught in moving parts.
● Non-skid footwear is recommended when working outdoors.
● Secure long hair, or wear protective hair covering.
Use personal protective equipment
● Use safety glasses
● Use face or dust mask when working operations create or involve dust.
Save all warnings and instructions for future reference. Refer to them frequently and use them to instruct others using Pegasus. If you loan someone Pegasus, loan them these instructions to prevent misuse of the product and possible injury.
Do not use tools in damp or wet locations. Damp or wet conditions prevent appropriate clamping pressure and grip on the work piece
Ensure the work piece is clamped firmly and the lock is engaged before use
Check damaged parts. Before using the tool, it should be carefully checked to ensure it will operate properly and perform its intended function
When not in use, tools should be stored in a secure, dry place, out of the reach of children and unauthorized usage.
Have your Pegasus serviced by a qualified repair person.
Warning
● The use of any accessory or attachment other than those recommended in this instruction manual may present a risk of personal injury.

SYMBOLS

Warning To reduce the risk of injury, user must read instruction manual.
**** Warning
Pinch points

COMPONENT LIST

A. Quick clamps (2 pieces)
B. Clamp dogs (4 pieces)

INSTALLATION INSTRUCTION

To use Pegasus as a work bench, open the legs fully and pull the table upward until latches “click” into place.(Fig. 1)

NOTE: Before using, check that the table is horizontal and two latches on the same side lock securely into the upper hole at the same time.
Align the Quick Clamps with the slot and insert it fully. Grip the Quick Clamps handle and put it into the groove as shown. Once the clamps are seated, release the handle. (Fig. 2-4)

Push the clamping dogs into the desired holes on the table. (Fig. 5)

NOTE: Make sure dogs are installed towards the rear jaw as shown
When working, use clamping dogs and two quick clamps for multiple clamping options. (Fig. 6-9)

Quick clamps can be used independently if desired. (Fig. 10)

locked together side by side or end to end with the enclosed joiners. (Fig. 13-14)
Use the recesses and tool tray for storage. (Fig. 11)

If necessary, power strips can be attached using zip ties (zip ties and power strips are not included). (Fig. 12)

If desired, multiple units can be locked together side by side or end to end with the enclosed joiners. (Fig. 13-14)

To use Pegasus as a sawhorse, open the legs fully until the tool tray is flat. It is compatible with our clamping sawhorse (not supplied). (Fig. 15)

To fold Pegasus for storage:

Press both latches and collapse the table. ( Fig. 16)
Lift the tool tray in the centre to allow the legs to fold. (Fig. 17)

WARNING: Keep fingers away from moving joints to avoid pinching If necessary, power strips can be attached using zip ties (zip ties and power strips are not included).