WORX WA4096 Gutterpro Universal Gutter Cleaning Kit Instruction Manual

October 27, 2023
Worx

worx-logo

WORX WA4096 Gutterpro Universal Gutter Cleaning Kit

SAFETY INSTRUCTIONS

WARNING! User must read the product manual to fully understand this product prior to use, and follow all safety instructions as outlined in the Worx AIRTM
CAUTION! The user must wear the appropriate clothing and safety goggles when operating this product. Be aware of all bystanders, pets and objects in a close proximity.

  • DO NOT operate blower and attachments when fatigued.
  • DO NOT overreach or stand on unstable support. Keep good footing and balance at all times.
  • Never direct airflow towards bystanders. Always be aware of the direction that the debris will be thrown.
  • Use a face filter mask to avoid breathing dust and debris.

WARNING: This product can expose you to chemicals including lead and Di(2-ethylhexyl) phthalate (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

COMPONENT LIST

WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-Kit-fig-
\(2\)

  1. GUTTER TUBE NOZZLE (QUANTITY OF 1)
  2. GUTTER TUBE EXTENSION (QUANTITY OF 3)
  3. GUTTER TUBE ADAPTOR (QUANTITY OF 1)
  4. GUTTER TUBE CONNECTOR (QUANTITY OF 1)
  5. UNIVERSAL ADAPTOR
  6. BLOWER TUBE ADAPTOR

ASSEMBLY AND OPERATION

WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-
Kit-fig- \(3\) WORX-WA4096-Gutterpro-
Universal-Gutter-Cleaning-Kit-fig- \(4\)

  1. Attach the Gutter kit as shown in Fig. A1 (for Worx TURBINE, TRIVAC models and other brands blowers), A2 (for WG545 models), A3 (for WG543 models): Connect the (1, 2, 3) components by screwing together. Snap the (3, 4, 5) or (3, 4, 6) components together, and then tighten the screw (Fig. A4).

  2. Assembling the Gutter Tube Adaptor
    Fit the gutter tube adaptor to the motor housing as shown in Fig. B1. Then tighten the screw. (Fig. B1.1) Check the gutter tube adaptor is firmly secured .WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-Kit-fig-
\(5\) WORX-WA4096-Gutterpro-Universal-
Gutter-Cleaning-Kit-fig- \(6\) WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-Kit-fig-
\(7\)

  3. Assembling the Universal Adaptor

  4. Place the fabric side of the Universal Adaptor over the Blower Outlet and slide it on as far as possible (B2).
    Worx TURBINETM models-Place the fabric side of the Universal Adaptor over the outlet of the Fan Housing and slide it on as far as possible(B2.1).

  5. Worx TRIVACTM models – Place the fabric side of the
    Universal Adaptor over the Vacuum Outlet and slide it on as far as possible (B2.2). Before operation, flip the blow/vac switch into the vacuum mode.
    PLEASE NOTE : Items can be vacuumed through the vac inlet and pass through or become clogged within the gutter kit. Please keep the vac inlet away from objects while using the gutter kit.

  6. Check to make sure the strap is threaded through the locking mechanism. Then pull to tighten the strap (B3). Increase the tension by pulling the latch up and down to tighten (B4). To loosen, simply press the two outside latches down and then pull the strap out from other side (B5).

  7. Test that the Universal Adaptor will not slide off of the blower outlet.

  8. If further tightening is needed, then pull the middle latch up and down until the adaptor is tight. Please recheck if it will slide off of the blower outlet. Realign and repeat these steps if needed (B4). To loosen, simply press the two outside latches down and then pull the strap out from other side (B5).
    PLEASE NOTE : The Universal Adaptor may have space between the Blower Outlet and Adaptor Outlet after installation.
    To remove the adaptor, simply press the two outside latches down and loosen the strap to remove it from the Blower Outlet (B5).
    NOTE: Use only enough Gutter Tube Extensions to comfortably reach the inside of the gutter.WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-Kit-
fig- \(8\) WORX-WA4096-Gutterpro-
Universal-Gutter-Cleaning-Kit-fig- \(9\)

  9. Assembling the Blower Tube Adaptor (for WG543 models)

  10. Press the Nozzle Release Button to remove the Airspeed Selector Nozzle from the Blower Tube. (See Fig. C1)

  11. Slide the Blower Tube adaptor on and make sure it firmly locks into position. (See Fig. C2, C3)

  12. Attach the Gutter kit.WORX-WA4096-Gutterpro-Universal-Gutter-Cleaning-Kit-fig- \(10\)

  13. Operate according to Fig. D:
    The Gutter Tube Nozzle can be adjusted to any desired direction by rotating the Gutter Tube Connector as shown in Fig. E. Gutter cleaning applications will vary. It is recommended to try various positions to find the most effective working position for the type of house and gutter design.

www.worx.com
Copyright © 2017, Positec. All Rights Reserved. Copyright © 2017, Positec. Tous droits réservés. © Derechos reservados 2017, Positec. Todos los derechos reservados. AR01528901

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Worx User Manuals

Related Manuals