Hope Ebike Crankset Instruction Manual

June 6, 2024
HOPE

Hope Ebike -logo

Hope Ebike -logo2

Hope Ebike -icon3

CAUTION: READ THIS BEFORE INSTALLING YOUR CRANKS!
Riding bicycles can be dangerous. These instructions should be read thoroughly before installation. Failure to follow these instructions before Installing and using Hope Technology Components can result in severe injury or death.
BOX CONTENTS
Drive Side Crankarm Assembly Non-Drive Side Crankarm Assembly

TOOLS REQUIRED

  • 8mm Hex
  • Torque Wrench with 8mm Hex

HOPE WARRANTY

All Hope Technology Components are covered for two years from the original date of purchase against manufacturer defects in material and workmanship. Proof of purchase is required. The product must be returned to the original retailer to process any warranty claim. This warranty does not cover any damage caused through misuse or failure to comply with the recommendations given in this manual. This warranty does not affect your statutory rights.
HOPE TECHNOLOGY (IPCOJ Limited
Hope Mill. Calf Hall Road Barnoldswick. Lancashire BB18 SPX. United Kingdom
T: 01282 851400 E Info@hopetech.com W: hopetech.com

PRELIMINARY CHECKS

00l _Check Compatability of cranks with the motor axle. This crank has an ISIS spline fitting as found on most Bosch. Brose and some other manufacturers motors.
002 _Consult fitment diagram and check frame clearance. Chainstay clearance requirements vary between bike manufacturers and even between models. It is important the crank arm does not foul on any part of the motor or frame.

INSTALL DRIVE SIDE CRANKARM

003 _Clean and then lightly grease the spline of the motor axle. Also, grease the thread in the end of the motor axle.
004 _Locate the crank arm onto the spline. It should be possible to align the crank into the spline before the bolt thread contacts. At this point, the angular position of the crank on the spline is not critical.Hope Ebike
Crankset-6

005 _Using an 8mm hex screw the crank bolt into the axle thread. Take care to get the thread started correctly before fully tightening. The bolt should turn freely and draw the crank onto the first part of the spline with minimal resistance.Hope Ebike Crankset-1

006 _Fully tighten the crank bolt, drawing the crank onto the axle spline. The further the crank is drawn onto the spline the more torque will be needed to turn the crank bolt. The crankarm will come to a solid stop against the shaft shoulder when properly located. Crank bolt recommended tightening torque: 50 N.mHope Ebike Crankset-2

INSTALL NON-DRIVE SIDE CRANKARM

007 _Clean and then lightly grease the spline of the motor axle. Also, grease the thread in the end of the motor axle.
008 _Locate the crank arm onto the spline. It should be possible to align the crank into the spline before the bolt thread contacts. Take care to align the crank at 180° to the drive side crank.Hope Ebike
Crankset-3

009 _Using an 8mm hex screw the crank bolt into the axle thread. Take care to get the thread started correctly before fully tightening. The bolt should turn freely and draw the crank onto the first part of the spline with minimal resistance.

01O_ Fully tighten the crank bolt. drawing the crank onto the axle spline. The further the crank is drawn onto the spline the more torque will be needed to turn the crank bolt. The crankarm will come to a solid stop against the shaft shoulder when properly located. Crank bolt recommended tightening torque: 5O N.mHope Ebike Crankset-4

Traduction
Hope Ebike Crankset [PDF]

PEDAL WASHERS

IMPORTANT : Please follow relevant manufacturers’ instructions for pedal installation. Pedal washers are provided to avoid damaging the crankarm. Some pedal axle designs have an integrated washer, in this case, washers are not required.
When using the pedal washers take care to center the washer in the counterbore, not doing this could cause damage to the crankarm.Hope Ebike
Crankset-5

DISASSEMBLY PROCEDURE (Same procedure for drive and non-drive crankarms]
001 _Using an 8mm hex turn the inner crank bolt on the crank arm anticlockwise to loosen it.
002 _Keep turning the bolt in an anticlockwise direction. it will go loose and then you will feel resistance as the crank starts to extract off the axle, keep turning until the drive side crank comes right off the axle.Hope
Ebike Crankset-7

Hope Ebike -logo3 HOPETECH.COM

Hope Ebike -icon3

Documents / Resources

| Hope Hope Ebike Crankset [pdf] Instruction Manual
Hope, Ebike, Crankset
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HOPE User Manuals

Related Manuals