dji Action 2 Remote Control Extension Rod User Guide
- June 6, 2024
- DJi
Table of Contents
ACTION 2
Remote Control Extension Rod
User Guide
Disclaimer and Warning
Congratulations on purchasing your new DJI OSMOw product. The information in
this document affects your safety and your legal rights and responsibilities.
Read this entire document carefully to ensure proper configuration before use.
Failure to read and follow instructions and warnings in this document may
result in serious injury to yourself or others, damage to your DJI OSMO
product, or damage to other objects in the vicinity. This document and all
other collateral documents are subject to change at the sole discretion of DJI
OSMO. This content is subject to change without prior notice. For up-to-date
product information, visit http://www.dji.com and click on the product page
for this product.
By using this product, you hereby signify that you have read this disclaimer
and warning carefully and that you understand and agree to abide by the terms
and conditions herein. You agree that you are solely responsible for your own
conduct while using this product and for any consequences thereof. You agree
to use this product only for purposes that are proper and in accordance with
all applicable laws, rules, and regulations, and all terms, precautions,
practices, policies, and guidelines DJI OSMO has made and may make available.
DJI OSMO accepts no liability for damage, injury, or any legal responsibility
incurred directly or indirectly from the use of this product. The user shall
observe safe and lawful practices including, but not limited to, those set
forth in this document. Notwithstanding the above, your statutory rights under
applicable national legislation are not affected by this disclaimer.
OSMO is a trademark of SZ DJI OSMO TECHNOLOGY CO., LTD. (abbreviated as “DJI
OSMO”) and its affiliated companies. Names of products, brands, etc.,
appearing in this document are trademarks or registered trademarks of their
respective owner companies.
Safety Guidelines
- DO NOT allow the product to come into contact with any kind of liquid. DO NOT leave the product out in the rain or near a source of moisture. DO NOT drop the product into
- Put out any product fire using water, sand, a fire blanket, or a dry powder fire
- The product should only be used in temperatures from -10° to 45° C (14° to 113° F). Use of the product in environments above 45° C (113° F) can lead to a fire or explosion while use in environments below -10° C (14° F) can lead to permanent
- DO NOT disassemble or pierce the product in any way. Otherwise, the battery may leak, catch fire, or explode.
- DO NOT drop or strike the DO NOT place heavy objects on the product.
- DO NOT heat the product. DO NOT put the battery in a microwave oven or a pressurized
- DO NOT leave the product near heat sources such as a furnace or DO NOT leave the product inside of a vehicle on hot days. DO NOT store the product in environments above 45° C (113° F). The ideal storage temperature is 22° to 28° C (71.6° to 82.4° F).
- DO NOT store the battery for an extended period after fully Otherwise, the battery may over-discharge and cause irreparable damage.
- Discharge and charge the battery completely once every three months to keep it in good working
Introduction
The DJI Action”’. 2 Remote Control Extension Rod expands users shooting capabilities with an extension rod and a tripod. Users can control the camera remotely and capture self ies with the WI Remote Control Pad.
Overview
-
1/4″ Screw
Compatible with adapters with 114* threaded -
Extension Rod
The length of the extension rod is 16.5 cm when stored and can be extended to up to 37.8 cm. There is also a tripod that can be unfolded for greater stability. -
WI Remote Control Pad
Connected to the camera via Bluetooth, the remote control pad supports single-camera control and also multi-camera control mode so that users can shoot with up to eight cameras simultaneously. -
WI Remote Control Pad Slot
Used to attach the remote control -
Link Button
Press and hold the link button for one second to link the remote control pad and the camera.
Press and hold the link button and the 50 buttons for tour seconds to forget the Bluetooth connection and start linking. Press and hold the link button and the shutter/record button for four seconds to switch between single-camera control mode and multi-camera control mode and start linking.
In multi-camera control mode, press the link button to display the number of cameras connected. -
Screen
When controlling a single camera, the screen displays the status and battery level of the connected camera. When controlling multiple cameras, the screen displays the number of cameras connected. The display on the screen varies depending on the camera model. The screen will not enter sleep mode while recording or charging.
The screen will enter sleep mode if there is no operation after 3 minutes and the remote control pad will power off if there is still no operation after a further 10 minutes if there is no camera connected and the remote control pad is not charging. When the screen is off, press any button to exit sleep mode and continue using the remote control pad. -
5D Button
Press the 50 buttons to enter the camera mode switch screen, push the joystick left or right to select a camera mode, and press again to confirm. -
Status LED
Refer to the Status LED Descriptions section for more -
Shutter/Record Button
Press and hold for one second to power the remote control pad on or off. After powering on, the remote control pad will automatically search for and connect to any OM Action 2 cameras.
Press once to take a photo or to start or stop recording.
In multi-camera control mode, press once to take a photo or to start recording and press twice to stop recording. -
USB-C Port
Connected to a charger to charge the remote control
• Installation is shown in Figures A and B. WI Action 2 and the adapters are
not included.
• The description above is for when controlling a single camera unless
otherwise specified.
The built-in battery of the remote control pad may run out of power if it is
not used for more than six months and will require charging to use again.
Charge or discharge the battery to 4060% if it will not be used for 10 days
or more.
Status LED Descriptions
Status Indicator
|
Descriptions
---|---
Charging Status
Solid green for 6 seconds and turns off| Charging completed
Blinks green four times| Charging with battery level between 76-100%
Blinks green three times| Charging with battery level between 51-75%
Blinks green twice| Charging with battery level between 26-50%
Blinks green| Charging with battery level between 0-25%
System Status
Blinks red three times| Powering off
Blinks blue| Linking
Work Status
Solid green| Ready to use
Temporarily off| Taking photo
Blinks red| Recording video
Specifications
General Settings
DJI Remote Control Pad Model BTC01|
Weight| Extension Rod: 110 g; DJI Remote Control Pad: 11 g
DJI Remote Control Pad Dimensions| 36.5×27.5×19 mm
Extension Rod Dimensions| 30x34x165 mm (Extended: 378 mm)
Bluetooth
Protocol| BLE5.0
Operating Frequency| 2.400-2.4835 GHz
Transmission Power (EIRP)
| ≤8dbm
Built-in Battery
Battery Type| Li-ion (65 mAh @ 3.7 V)
Charging Type| Connected to USB-C port (5 V)
Charging Time*| 55 mins
Operating Time**| 5 hours
Charging Temperature| 5 to 45° C (32° to 113° F)
Operating Temperature| -10° to 45° C (14° to 113° F)
- Measured using a 5V/2A USB adapter in a laboratory environment. Use as a reference only.
**Measured using single-camera control mode, with the remote control pad screen on. Use as a reference only.
**WE ARE HERE FOR YOU
Contact DJI SUPPORT** via Facebook Messenger
http://weixin.qq.com/q/02Y8HiZQ_2eF410000g03M
This content is subject to change without prior notice.
Download the latest version from
https://wvvvv.dji.com/action-2
If you have any questions about this document, contact DJI by sending a
message to
DocSupport@dji.com.
Copyright © 2021 DJI OSMO All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>