WORX WG602 Electric Pressure Washer Instruction Manual

WORX WG602 Electric Pressure Washer

GENERAL SAFETY WARNINGS

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
WARNING: This product can expose you to chemicals including lead and Di(2-ethylhexyl) phthalate (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product basic precautions should always be followed, including the following:

1. Read all the instructions before using the prod-uct.
2. To reduce the risk of injury, close supervision is necessary when a product is used near children.
3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.
4. Stay alert – watch what you are doing.
5. Do not operate the product when fatigued or under the influence of alcohol or drugs.
6. Keep operating area clear of all persons.
7. Do not overreach or stand on unstable support. Keep good footing and balance at all times.
8. Follow the maintenance instructions specified in the manual.
9. This Product Is Provided With A Ground Fault Circuit Interrupter Built Into The Power Cord or Plug. If Replacement Of The Ground Fault Circuit Interrupter Or Cord Is Needed, Use Only Identical Replacement Parts.

SAVE THESE INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug or the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the ground-fault circuit-interrupter or cord become necessary, use only identical replace-ment parts.

SERVICING OF A DOUBLE-INSULATED APPLIANCE
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor should a means for grounding be added to the product. Servicing a double- insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace.

EXTENSION CORDS

WARNING: Inadequate extension cords can be dangerous.
If the appliance cord is equipped with a GFCI, do not use extension cords. If the appliance cord is not equipped with a GFCI, the appliance and any extension cord used should be connected only to a GFCI-protect-ed power source.

1. Use only extension cords that have grounding-type plugs and female cord connectors that accept the plug from the product.
2. Use only extension cords that are intended for out-door use. These extension cords are identified on the packaging or on the cord by a marking “Accept-able for use with outdoor appliances; store indoors while not in use.”
3. Use only extension cords having an electrical rating not less than the rating of the product.
4. Do not use a damaged extension cord. Examine ex tension cord before using and replace if damaged.
5. Do not abuse extension cord and do not yank on a cord to disconnect.
6. Keep cord away from heat and sharp edges.
7. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.
   WARNING – To reduce the risk of electrocution, use only a GFCI-protected extension cord or plug into GFCI outlet. Keep all connections dry and off the ground. Do not touch plug with wet hands.

ADDITIONAL SAFETY WARNINGS

1. The electric supply connection shall be made by a qualified electrician and comply with IEC 60364-1.
   It is recommended that the electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device that will prove the earth circuit.

2. WARNING: This appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance.

3. WARNING: Do not use the appliance within range of persons unless they wear protective clothing.

4. WARNING: High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment or the appliance itself.

5. Do not direct the jet against yourself or others in order to clean clothes or foot-wear.

6. Disconnect from the electrical power supply before carrying out user maintenance.

7. High pressure cleaners shall not be used by children or untrained personnel.

8. To ensure appliance safety, use only original spare parts from the manufacturer or approved by the manufacturer.

9. WARNING: High pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.

10. Do not use the appliance if a supply cord or important parts of the appliance are damaged, e.g. safety devices, high pressure hoses, trigger gun.

11. Water that has flown through backflow preventers is considered to be non-potable.

COMPONENT LIST

1. CARRY HANDLE (WAND HOLDER)
2. ONBOARD NOZZLE STORAGE
3. WATER PUMP
4. POWER CORD
5. ON /OFF SWITCH
6. LANCE HOLDER
7. POWER CORD HOLDER
8. HIGH PRESSURE HOSE
9. NOZZLE (40°)
10. TURBO NOZZLE
11. WATER INLET
12. RECLOGGING NEEDLE
13. SOAP BOTTLE*
14. LOCK-OUT
15. TRIGGER
16. WAND
17. LANCE
18. NOZZLE COUPLER
19. RESET BUTTON
20. TEST BUTTON
21. O-RING
22. POWER CORD CLIP

*Not all the accessories illustrated or described are included in standard delivery.

TECHNICAL DATA

|

WG602

---|---
Rated current|

13 A

Rated pressure|

1700 psi (117 bar)

Rated water flow rate|

1.2 gpm

Power cord length|

35 ft (10.5 m)

Max water temperature|

104°F (40°C)

Protection class|

 /ll

Machinery weight|

16.1 lbs (7.3 kg)

ACCESSORIES

|

WG602

---|---
40°Nozzle|

1

Turbo Nozzle|

1

20ft Hose|

1

Declogging needle|

1

We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

ASSEMBLY & OPERATION

ASSEMBLY

Attach the lance to the wand.
Note: when attaching, align the two projections on the lance with the grooves on the wand.

Screw & Unscrew the high pressure hose
Note: Make sure the hose is tightly connected.
Note: For convenience of unscrewing the hose, please pull the trigger to drain water from wand when operation is completed and switch is in “O” position.

Attach the garden hose
Connect one end of the home garden hose (not supplied) to the adapter and another end to waterspout.

OPERATION

Extension Cord
It is not recommended to use the extension cord. If necessary, ensure the plug and ex- tension cord connection is on an elevated surface that does not contact the water area.

GFCI Plug Test
Press “test”, the light will be out. Press “reset”, the power regains and the light will illuminate.
Note: To keep good operation of GFCI, please implement it once a month.

START/STOP
Turn on the water supply tap. Connect the washer to the power supply and turn the switch to “I” position. Then press trigger
Note: Before pressing trigger, Push the lock-out down into the trigger.
WARNING: Do not start the machine without connecting and turning on the water supply because it may cause damage to high pressure seals and reduce the service life of pump.

Release the trigger and turn the switch to “O” position. Turn Off the water supply tap
Note: When not in use, Push the lock-out up until it clicks into the slot.

Select the right nozzles
Select the suitable nozzle for different cleaning jobs.
Nozzle 400(white) is applicable for cleaning on wooden and other soft objects.
Turbo nozzle is applicable for cleaning concrete, bricks and masonry.
WARNING: Do not change the nozzle pattern when the tool is powered on.

Cleaning
Begin with the nozzle 1-2ft away from the surface and approach with caution until it reaches the desired position for overly close spray may do harm to surface.
WARNING: Do not connect the machine to water supplies that are dirty, rusty, muddy, or corrosive. (Including window cleaning liquids, plant foods, or fertilizers etc.)

Using the power cord holder
To wind the power cord, turn the holders outwards. To unwind the power cord, pull out the holders and turn them inwards.

ATTACHMENT OF ACCESSORIES

Note: Do not attempt to use the washer with no lance or accessories attached.

Soap bottle (sold separately)
Soap bottle provides detergent suds for deeper cleaning of dirt.

MAINTENANCE

Remove plug from the socket before carrying out any adjustment, servicing or maintenance.
Inspect the product for damaged or worn parts before each use. Do not operate it if you find damaged or worn parts. Contact your supplier or the manufacturer for replacement parts.

Power Cord Maintenance
If the electrical cord is damaged, do not attempt to repair yourself; call the Worx solutions center for further assistance.

Pump Maintenance
Inspect the pump frequently whether any leaking occurs around the pump seal. If leaking occurs, contact the solutions center for further assistance.

Nozzle Maintenance
Remove the nozzle from the lance, then remove any possible obstructions using the included declogging needle (See Fig. L).Then use a garden hose to rinse the nozzle by backwashing

WARNING: Any other servicing should be performed by an authorized service representative.

STORAGE

1. Disconnect the water source. Turn on the pressure washer for a few seconds until the remaining water flows out. Then turn it off quickly.
2. Unplug the power supply .Wind power cord on the tool and use power cord clip to fix.
3. Disconnect the high pressure hose and the garden hose (not supplied), and coil high-pressure hose for storage. Insert the Wand and lance separately into the Wand Holder and lance holder.
4. Store in a frost free area with a temperature above 0°C (32°F).

TROUBLESHOOTING

Symptom

| Possible Causes|

Solution

---|---|---
Machine does not start when the switch is in “I” position.| Power cord is not plugged in.| Plug in power cord.
Socket is defective.| Check or replace plug, socket, fuses.
GFCI is triggered.| Press reset on GFCI plug.
Machine pressure is not consistent.| Pump is faulty.| Contact service center.
Air in line.| Remove the nozzle, turn on the machine for a while and install the nozzle back.
Water inlet adapter is clogged or dirty.| Remove the adapter, rinse it with water and put is back.
The pressure of the pump is not adequate| Water supply is Insufficient.| Open water source completely.
Water supply is restricted.| Check If the water hose kinks or leaks.
Diameter of garden hose is too small.| Replace with right garden hose.
Leak or kick in hose.| Replace hose or untie kinks in hose.
Lance leaks| O-ring needs to be replaced| Replace o-ring .If the problem is not solved, contact service center to buy a new lance.

References

• P65Warnings.ca.gov
• P65Warnings.ca.gov
• Lawn & Garden Equipment | Innovative Power Tools | WORX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>