SONOFF NSPanel Smart Scene Wall Switch User Manual
- June 6, 2024
- SonOFF
Table of Contents
Works with everything
User manual V1.1
Smart Scene Wall Switch
Product Intro$duction
The device’s weight is less than 1 kg. An installation height of less than 2 m is recommended.
The device’s weight is less than 1 kg. An installation height of less than 2 m is recommended.
Features
NSPanel is a dual-channel smart touch control panel integrating three interactive methods, screen touching, voice control, and App control. Users can control the device types including smart switches and plugs heating/cooling) under the eWeLink account. Users are able to control multiple smart devices through adding widgets on their smartphones, such as turn on/off, scheduled on/off the connected devices and share them with families to control.
Operating Instruction
-
Power off
Please install and maintain the device by a professional electrician. To avoid electric shock hazards, do not operate any connection or contact the terminal connector while the device is powered on! -
Wiring instruction
Light fixture wiring instruction:
Make sure all wires are connected correctly. -
Download the eWeLink App
|
---|---
4. . Power on
After powering on, the device will enter the Bluetooth pairing mode during
the first use.
The screen status is shown in the above image.
- Add the device
Tap “+” and select “Bluetooth pairing”, then operate following the prompt on the App.
Operation Guide
Dropdown
Settings of the screen brightness and sleep time
Swipe right
After adding the temperature controller function in the App, you can set the
added temperature controller on the device.
Swipe left
After adding widgets to the App, you can control the added widgets on the
device.
Bind Temperature Control Device
There is a built-in temperature sensor in the panel to monitor the room
temperature and you
can maintain the room temperature by controlling the cooler/heater, which is
connected with smart switches or smart plus, and these devices are required to
pair with the eWeLink app.
Access the panel interface in the App and tap “Thermostat” to select the
devices in the Action device list. All the listed devices are supported to
bind with the Thermostat (including two
NSPanel channels). You can only select one device or one channel of the multi-
channel device to execute and then choose heater or cooler as the Device type.
Active the Thermostat after
selecting the Action device and Device type, then you can see there are two
modes to control the temperature which are Manual mode and Auto mode.
Manual mode:
Allow you to adjust the temperature manually whenever you want and then the
Thermostat will execute to maintain the manual setting temperature.
Auto mode:
Allow you to set 6 target temperatures at most by tapping “Add” to set the
temperature respectively.
Once set, all settings will execute automatically at certain time duration and
cannot be controlled manually unless switched to the Manual mode. The binding
devices will turn off when they are out of schedule.
Actual room temperature will be ±1℃. For example, the setting temperature is
26℃ but the actual temperature range is between 25℃ and 27℃.
Add Widgets
NSPanel can be added 8 widgets in the screen for Quick Control. The form of a
widget can be a single device, group devices of the congeneric devices, and
Tap to Perform Scene. In addition, you can control more features of the multi-
gang and lighting devices in the secondary interface.
Specifications
Model | NSPanel-EU, NSPanel-US |
---|---|
Input | 100-240V ~ 50/60Hz 4A Max |
Output | 100-240V ~ 50/60Hz 2A/Gang 4A/Total |
LED load | 150W/110V/Gang,300W/110V/Total |
300W/220V/Gang,600W/220V/Total
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
Bluetooth Standard| 4.2 BLE
Screen Size| 3.5″ (Capacitive Touch Panel)
Screen Resolution| 480*320px
Operating systems| Android & iOS
Shell materials| PC V0+CRS+Toughened Glass
Dimension| NSPanel-EU: 86x86x41.7mm
NSPanel-US: 120x74x41.7mm
Re-establish Pairing of the NSPanel
When you want to change the NSPanel’s account or connected WIFI, it requires you to pair the NSPanel again. Press any bottom of the device for 5s until the screen indicates that it had entered into Bluetooth pairing mode and then release. Now the NSPanel is available for Bluetooth pairing in the eWeLink app.
The device will exit the Bluetooth pairing mode if not paired
within 3mins.
Factory Reset
Deleting the device on the eWeLink app indicates you restore it to the factory
setting.
Common Problems
Fail to pair Wi-Fi devices to eWeLink App
-
Make sure the device is in pairing mode. After three minutes of unsuccessful pairing, the device will automatically exit pairing mode.
-
Please turn on location services and allow location permission. Before choosing the Wi-Fi
network, location services should be turned on and location permission should be allowed.
Location information permission is used to obtain Wi-Fi list information. If you click Disable, you will not be able to add devices. -
Make sure your Wi-Fi network runs on the 2.4GHz band.
-
Make sure you entered the correct Wi-Fi SSID and password, no special characters are contained. A wrong password is a very common reason for pairing failure.
-
The device shall get close to the router for a good transmission signal condition while pairing.
FCC Warning
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled
environment. This equipment should be installed and operated with a minimum
distance20 of cm
between the radiator & your body. This transmitter must not be co-located or
operating in
conjunction with any other antenna or transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type NSPanel-EU, NSPanel-US is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, Shenzhen, GD, China
ZIP code: 518000 Website: sonoff.tech
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>