DAYI D-25 Safe Box Instruction Manual

product Manual

Please do not lock the emergency key and emergency battery box into the cabinet.
Have any issues? Please contact us: DAYI_service@outlook.com

Component Description

1. Green light
2. The delete key(*)
3. Emergency keyhole cover
4. Emergency power jack
5. Yellow light
6. Red light
7. Confirming button(#)
8. Knob

1. Internal battery case
2. Locking bolt
3. Key Hook
4. Setting button
5. Shelf

Have any issues? Please contact us: DAYI_service@outlook.com

Parts List

Safe box *1

Quick start guide1    Emergency battery box1      Foot mat*4

Emergency key2                 Expansion screws4

Warnings

1. Do not lock the emergency key or emergency battery box into the cabinet.
2. The initial password is “123456”, need to be modified.
3. If the safe box is not used for a long time, the battery should be removed to prevent leakage of liquid from damaging the electronic system.
4. Purchase 4 AA batteries in advance, this safe does not contain batteries.

System Setting

Step1 Open the safe box for the first time

Press the right edge of the emergency keyhole cover, insert the emergency key, and turn it 90° counterclockwise, then turn the handle clockwise to open the door successfully for the first time

Step2 Insert the battery

Remove the internal battery case cover and install the 4 AA 1.5 Volt alkaline batteries, the system will power on.
(Note: Rechargeable battery is not recommended as it may destroy safe box’s internal electronic components)

Step3 Set the digital password

Note: 1. The user can set one independent passwords for the lock.
2. The initial password is “123456”, need to be modified.
3. The password consists of a minimum 1 number and maximum 8 numbers.

1. Setting button

Set Password

To set the password , the door must be opened first, then press the Setting button on the inner side of the door. Buzzer “di” will sound, the screen will display “ Red light “.
(1) Then enter your password , and press “#”.
(2) Repeat the password, then press “#” to confirm.
(3) The screen will display “ Green light ” indicate success.

Tip: 1. A single “di” sound indicating that the password has been set successfully, “di di di” sounds indicate that the user does not enter the same password, please repeat the procedures.
2. Please verity the passwords after done the passwords setting, and lock the door after verification.

Three ways to open the door

1. The first unlocking method: Use the emergency key.

Insert the emergency key into the right keyhole, and turn it 90°counterclockwise, then turn the handle clockwise to open the door (Suitable for unlocking or for the first time, forgetting the password, or when the battery is dead).

2. The second unlocking method: Use the keyboard password.

After installing the battery, press the “#” key, enter your password and then press the “#” key, Green indicator light is on, Then turn the knob to the right to open the door.

3. The third unlocking method: Use the emergency battery box + password.

When the safe box’s battery is too low to open the door, insert 4AA batteries in the emergency battery box, plug the emergency power cord into the emergency power jack on the bottom edge of the panel, then enter the correct password to open the door.

Dual Alarm System

1. After 3 consecutive time of wrong code, your safe will activate the alarm system, the alarm will sound for one minute, then enter the correct password and the alarm will be cancelled. If you want to turn off the alarm immediately, you need to open the safe with the emergency key, and then remove the battery.
2. In standby state, press the “*” button, all the lights are on at the same time, and then a beep of “di” , the Vibration alarm mode is turned on. If the box is shaken or violent hit, it will give an alarm immediately, at this point, enter the correct password to stop the alarm.

• When power on, the system default for alarm is off.
• When the door is opened, the alarm is turned off and needs to be turned on again.

Under-voltage warning

After opening the door, the buzzer “beep” will ring 9 times alarm, reminding the user that the battery power is low and the user needs to replace the battery.

How to use the adjustable shelf

Turn the fastener clockwise and pull out the fastener horizontally, you can adjust the position of the shelf or take out the shelf according to your needs.

How to install foot mat?

1. Remove the stickers of the four foot mats
2. Install the four foot mats on the bottom of the safe

| How to mount the safe?

1. Place the safe at the installation place. Mark the drilling spots on the wall from the inside pre-drilled holes, then remove safe and drill four holes.
2. Put the expansion bolts into the drilled holes, take the expansion bolt out of the sleeves, then place the safe and align the pre-drilled holes with drilled holes, and insert the expansion bolts into its sleeves from inside of the safe.

---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>