FOTILE GLG30401-Y 30 Inch Moonshadow Tri-Ring Cooktop Installation Guide
- June 1, 2024
- FOTILE
Table of Contents
QUICK INSTALLATION GUIDE
30″ BUILT-IN GAS COOKTOPS
MODELS: GLG30301,GLG30401-Y,GLG30401
PACKAGE LIST
Note: In this document, we take the image of model GLG30401-Y/GLG30401 as an example. Compared with it, model GLG30301 does not have Simmer Burner and its control knob, and the Center Grate is slightly different.
Installation Details
Installation Information:
Gas Connection:
Suggested Installation for No Appliance obstruction below the cooktop|
Suggested installation to avoid appliance interference below cooktop
---|---
A. Manifold pipe
B. Regulator provided with unit:
● Outlet – 1/2” NPT female pipe thread
● Inlet – 1/2” NPT female pipe thread
C. Adapter
● Outlet – 1/2” NPT female pipe thread
● Intet – 3/8” NPT female pipe thread
D. Flexible connector
E. Adapter
F. Manual shut-off valve
G. Gas pipe| 
| A.
Manifold pipe
B. Elbow
C. Adapter
● Outlet – 1/2” NPT female pipe thread
● Inlet – 1/2” NPT female pipe
D. Flexible connector
(allows passage through cabinet wall)
E. Adapter
F. Regulator provided with unit:
● Outlet – 1/2” NPT female pipe thread
● Inlet – 3/8” NPT female pipe thread
G. Gas pipe
H. Manual shut-off valve
I. Gas pipe| 
- FOTILE gas cooktops are manufactured and shipped to be used with natural gas. If you want to use LPG, please convert the cooktop to LPG following the instructions in the Installation Manual.
Burner Assembly Guide
◼ Tri-Ring Power Burner Assembly
STEP 01
Hold the burner head so
the shiny silver side is facing down. Find the small hole in the burner head
as noted in this picture.
STEP 02
Place the burner head onto the cooktop surface so that “hole A” gets inserted
into “pin B” on the cooktop. Make sure “Pin B” is firmly seated into “hole A”
on the burner head. If not, remove the burner head and try it again. Please
refer to the pictures below for this step.
STEP 03
Place the lined part of the outer burner cap to fit in the lined part of the burner head. Shake the outer burner cap gently to check if it is firmly seated (you will be able to rotate the outer burner cap, but it should be firmly seated in the burner head).
STEP 04
Next, place the inner burner cap on the burner head and make sure it is
firmly set by gently sliding it from side to side.
STEP 05
Check if the burner head/burner cap is firmly seated. If the burner head/Cap
is not level or is unstable, you must take it off, and reinsert it again.
| Burner head placed wrong| | Inner burner cap placed wrong
---|---|---|---
| Inner&outer burner cap placed wrong| | Placed correct
Other Burner Assembly
Identify 13200BTU/5800BTU/3000BTU burner head and burner cap by size.
STEP 01
Hold the Burner head, then find the gap“C’”and ignition needle “D”, make it on
the same side.
STEP 02
Place the burner head with the gap“C” next to the ignition needle“D”’and make
sure the burner head is firmly seated.
STEP 03
Place the lined part of burner cap to fit in the lined part of the burner
head. Shake the burner cap gently to check if it is firmly seated.
STEP 04
Check if the burner head/burner cap is firmly seated. If the burner head/Cap
is not level or is unstable, you must take it off, and reinsert it again.
| 
| 
---|---|---
Burner head placed wrong| Burner cap placed wrong| Burner head placed wrong
| 
| 
Placed correct| Placed correct| Placed correct
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>