FEIT CAM/WM/WIFI Smart Outdoor Camera Installation Guide
- June 6, 2024
- Feit
Table of Contents
FEIT CAM/WM/WIFI Smart Outdoor Camera Installation Guide
Safety Information
IMPORTANT SAFEGUARDS
ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT
WARNING: This produN may represent a possible shock or fire hazard if improperly installed or attached in any way.
Product should be installed in accordance with the owner’s manual, current electrical todes and/or the current National Electric Code (NEC}.
RISK OF ELECTRIC SHOCK: Turn off the main power
CAUTION: Please read all information carefully before installation
CAUTION: If you are unfamiliar or inexperienced with your home’s electrical systems, comact a cenified electrician for assistance
CAUTION: Intendal for ouBoor use. May be used indoon.
Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, bSA 562-463-2852 Unique Identifier: CAM/D00RMIFI
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, induding interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment
The device has been evaluated to meet general RF exposure requirement
The device can be used in portable exposure condition without restriction.
The device can be used in mobile (min 7.87 in.) exposure condition without
restriction.
Limited Warranty
This product is warranted to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please contact Feit Electric at [email protected], visit feit.com/contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
Tools Required to Mount Camera
-
Phillips Screwdriver
-
Pencil
-
Power drill
Hardware Included
Note: Hardware not shown to actual size.
Part
| Description| Quantity
---|---|---
AA| Smart Outdoor Camera
|
1
BB
| Power Adapter
| 1
CC| Mounting Screws
|
6
DD
| Mounting Anchors
| 6
EE| Hex Key
|
1
Description
Input Power: 12VDC, Max. 1A
Status Light|
- Blinking RED = Pairing Mode Solid RED = NoWi-Fi Connection
- Blinking BLUE = Connecting to Wi-Fi
- Solid BLUE = Connected to Internet
SD Card Slot| Add 128GB or less microSD card to enable recording (not
included). Only supports microSD card with FAT32 format.
Reset| Press and hold for 5 seconds on the Reset button to reset the camera.
Mounting & Installation
-
Mark Screw Positions
Mark screw positions using the Camera Bracket (AA) on your wall.
-
Inserting the Mounting Anchors
Drill holes at the marked points if installing on a hard surface such as concrete or brick. Insert Mounting Anchors (DD) into holes. You can skip this step if installing on wood or siding.
-
Feeding the cable thru the Camera Bracket
The cable can go through the base slot of the Camera Bracket (M) or drill a hole in the wall if the cable needs to go through there.
-
Attaching the Camera Bracket
Use the Mounting Screws (CC) to attach the Camera Bracket (AA) to the wall.
-
Adjust Camera
Use the Hex Key (EE) to loosen the hex screws then adjust and rotate viewing angle on the Smart Outdoor Camera (AA).
-
Plug into Wall Outlet
After adjusting, tighten all hex screws. Connect the cable from the camera to the Power Adapter (BB). Plug the camera into an outlet or surge protector.
Note: When using outdoors, plug the camera into an outdoor rated GFCI receptacle with appropriate outdoor cover.
APP Setup
Download and install the Feit Electric app
- Search for the Feit Electric app in the App Store or Google Play Store.
- Download and install the Feit Electric app on your smart device.
Set up the smart outdoor camera using the Feit Electric app
- Check to be sure the camera is in pairing mode. The RED indicator light must be blinking rapidly to connect. If not already blinking, press and hold the Reset Button until you hear an audible tone. Use the Feit Electric app to complete the set up.
- Tap Add Device or the + sign, then select Camera and confirm. You will be prompted to enter your Wi-Fi network and password.
Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.
Need Help
FAQs and the latest versions of user guides can be found at feit.com/help and feit.com/smart. To reach customer support please visit feit.com/contact-us
