SEBSON Motion Detector User Manual
- June 6, 2024
- SEBSON
Table of Contents
SEBSON Motion Detector
SEBSON Motion Detector
Thank you for choosing a product of SEBSON. Please read the instructions
carefully and keep them for looking up before start-up this product. A long
and failure-free operation can only be guaranteed if the installation and
start-up is done properly.
Before starting up this product, please check for external damage. In case of
visible external damage we immediately dis-advise the start-up of this
product!
Please remove all packaging material of this product before the first start-up
an and check the content for completeness!
Intended use:
This SEBSON motion detector has an IR sensor that detects the heat radiation
of moving objects and activates e.g. a connected light.
Scope of delivery:
1 motion detector
General safety information:
Danger:
- The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!
- In case of damages or contact with water turn off this product immediately without tension and make sure that a restart is no longer possible!
Danger of suffocation:
Please keep this product away from children and animals. The packaging
contains small parts that can be swallowed!
Caution:
Avoid overloading the device, an overload can damage the device or cause a
short circuit! Therefore, please note the maximum power consumption in the
technical data!
- The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
- The manufacture does not accept any responsibility for injuries or damage resulting from improper use of this product!
- Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire etc.
- We reserve the right to make changes to the product, the packaging or the operating instructions as well as printing errors.
- This product is only suited for indoor-use and not for outdoor-use!
- Protect the product from external damage, heavy dirt, moisture and excessive heat!
- In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
- In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.
Instruction for installation (Fig 5):
Danger:
Before installing please make sure that the circuit is interrupted! For
installation, the work on the mains voltage is required. Please remove the
associated mains fuse or deactivate the switch fuse! Check by using a voltage
tester if the line is de-energized. Make sure that the current circuit will
not closed during the installation!
Danger:
The installation of this product may be done only by a qualified person
according the valid regulations for electrical installation!
Attention:
Before drilling the mounting holes, make sure that there are no gas,
electricity or water pipes at the drilling location that could be damaged by
this!
-
Please observe the safety instructions and technical data before installing this product!
-
Note on installation:
L: Live wire (black or brown)
N: Neutral conductor (blue or grey) -
This device is only suitable for wall mounting!
-
For optimum range, select the mounting height recommended in the “Technical Data”.
-
2 units in a parallel connection (see Fig.4a)
- Permanently switching a connected device on or off with a switch (see Fig.4b).
To ensure optimum sensitivity of the sensor, install the device in the room in such a way that the movements are transversely to the device. Movements that are directly to and from the device are less well detected. (see Fig. 2a):
The following environments or surfaces are not suitable for mounting, as they may impair the detection of thermal radiation (see Fig. 2b):
- Metal surfaces e.g. metal door frames
- In the immediate vicinity of electronic devices such as computers, monitors etc
- Heat sources e.g. radiant heaters, radiators or lamps
- In the vicinity of e.g. fume cupboards or fans
- Within the radiation range of luminaires (minimum distance from luminaires >50cm)
Function of the motion sensor:
The sensor integrated in this device detects heat radiation from moving
bodies, e.g. people or animals, and transmits this as an electrical impulse to
a connected light, for example. This device then switches itself on. The
detection of heat radiation can be limited by large furniture, glass panes or
very high ambient temperatures of over 40°C, for example in summer.
Disabling and activating the motion detector:
- ON: Sensor deactivated-Connected device is switched on
- OFF: Sensor deactivated- Connected device is switched off
- PIR: Motion detector is activated after 30 seconds (warm-up phase)
Detection area (Fig 3): The detection range of the motion detector is approx. 9m and 160° (free area) at a mounting height of 1-1,8m on the wall. In closed rooms the detection distance can be lower, according to room layout.
Connection of the protective conductor (PE):
If a lamp with protective earth contact is connected and a junction box is not installed, the protective earth must be bridged from the supply line to the lamp by means of an additional terminal in the housing of the motion detector.
Sensitivity when switching (with regard to the ambient brightness):
This setting control can be used to regulate the switch-on sensitivity of this unit depending on the ambient brightness (between 3 and 2.000 LUX).
Time setting (switching off delay):
The duration of the operating time can be set continuously from approx. 10s
to 30min. The timer is restarted if a movement from the sensor is detected
before the set time has elapsed.
Function test:
Ensure that the motion detector is not obscured. Ensure that the coverage
area is not restricted by items such as through large furniture. To set the
detection range and the daylight test, turn the knobs to the positions shown.
The motion detector is activated after a warm-up phase of approx. 30s. If no
further movement takes place in the sensing area of the sensor, the sensor
switches off.
Technical Data:
Technical Data:
Operating voltage:| 220 -240V AC 50Hz
Maximum power consumption:
|
Max. 800W Max. 400W
Consumption in standby:| < 0,5W
Electrical protection:| IP20
Protection class:| II
Delay fuse:| 4A/ 250V
Detection moving speed:| 0,6-1,5m/s
Ambient temperature:| -20° – +40°C
Humidity:| <93%
Possibilities of adjustments:
Possibilities of adjustments:
Detection area:| Max.9m (<24°C)/160°
Sensitivity when switching (with regard to
the ambient brightness):
| <3-2.000LUX
Time setting (switching off delay):| Min. 10s +/- 3s – Max. 30min
+/-2min
Disposal note
This product may not be disposed of with household waste. At the end of its
useful life, the product must be returned to a point of acceptance for the
recycling of electric and electronic device. Please ask your local
municipality for the point of acceptance! As the devices contain valuable
recyclable materials, they should be sent for recycling, in order not to harm
the environment or human health from uncontrolled waste disposal.
Cleaning:
Danger: Before start cleaning the product interrupt the current circuit by
switching off the circuit breaker or unscrew the fuse! Use a slightly
moistened cloth for cleaning. In order not to damage the product, it is
essential to avoid water penetrating into the housing! Never clean the device
under running water! Do not use solvent-containing cleaner for cleaning.
CE Declaration of Conformity:
This product has been prepared according to the listed below guidelines:
- LVD 2014/35/EU
- EMC 2014/30/EU
- RoHS 2011/65/EU
Address : SEBSON Sebastian Sonntag Gernotstr.17 44319 Dortmund Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>