SEBSON Motion Detector User Manual

: June 6, 2024
: SEBSON

Table of Contents

SEBSON Motion Detector
- Intended Use
- Scope of Delivery
General Safety Information
Instruction for Installation
Function of The Motion Sensor
Detection Area
Cleaning
CE Declaration of Conformity
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEBSON Motion Detector

IR OUT A&AA

Instructions 01

Instructions 02

Instructions 03

Instructions 04

Instructions 05

Please read the instructions carefully and keep them for looking up before start-up this product. A long and failure-free operation can only be guaranteed if the installation and start-up is done properly. Before starting up this product, please check for external damage. In case of visible external damage we immediately dis-advise the start-up of this product! Please remove all packaging material of this product before the first start-up an and check the content for completeness!

Intended Use

This SEBSON motion detector has an IR sensor that detects the heat radiation of moving objects and activates e.g. a connected light.

Scope of Delivery

1 motion detector
Screws for fixing (2 pieces)
Dowels Ø 6mm (2 pieces)

General Safety Information

Danger: The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!
Danger: If the power cables are damaged or come into contact with wetness, immediately disconnect the product from the power supply and ensure that it cannot be switched on again!
Danger of Suffocation: Please keep this product away from children and animals. The packaging contains small parts that can be swallowed!
Caution: Avoid overloading the device, an overload can damage the device or cause a short circuit! Therefore, please note the maximum power consumption in the technical data!

The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
The manufacture does not accept any responsibility for injuries or damage resulting from improper use of this product!
Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire etc.
We reserve the right to make changes to the product, the packaging or the operating instructions as well as printing errors.
This product is suited for indoor- and outdoor-use.
Protect the product from external damage, heavy dirt, moisture and excessive heat!
In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.

Instruction for Installation

Danger: Before installing please make sure that the circuit is interrupted! For installation, the work on the mains voltage is required. Please remove the associated mains fuse or deactivate the switch fuse! Check by using a voltage tester if the line is de-energized. Make sure that the current circuit will not closed during the installation!
Danger: The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!
Attention: Before drilling the mounting holes, make sure that there are no gas, electricity or water pipes at the drilling location that could be damaged by this!

Please observe the safety instructions and technical data before installing this product!
Note on installation:
L: Live wire (black or brown)
N: Neutral conductor (blue or grey)
This device is suitable for wall or ceiling mounting!
Observe a minimum distance of 2 meters when commissioning several motion detectors.
For optimum range, select the mounting height recommended in the “Technical Data”.
2 units in a parallel connection.
Permanently switching a connected device on or off with a switch.

To ensure optimum sensitivity of the sensor, install the device in the room in such a way that the movements are transversely to the device. Movements that are directly to and from the device are less well detected:
The following environments or surfaces are not suitable for mounting, as they may impair the detection of thermal radiation:

Metal surfaces e.g. metal door frames
In the immediate vicinity of electronic devices such as computers, monitors etc
Heat sources e.g. radiant heaters, radiators or lamps
In the vicinity of e.g. fume cupboards or fans
Within the radiation range of luminaires (minimum distance from luminaires >50cm)

Function of The Motion Sensor

The sensor integrated in this device detects heat radiation from moving bodies, e.g. people or animals, and transmits this as an electrical impulse to a connected light, for example. This device then switches itself on. The detection of heat radiation can be limited by large furniture, glass panes or very high ambient temperatures of over 40°C, for example in summer.

Detection Area

The detection range of the motion detector is approx. 12m and 180° (free area) at a mounting height of 1,8-2,5m on the wall. In closed rooms the detection distance can be lower, according to room layout.

Connection of The Protective Conductor (PE)

If a lamp with protective earth contact is connected and a junction box is not installed, the protective earth must be bridged from the supply line to the lamp by means of an additional terminal in the housing of the motion detector.

Connection of the protective conductor

Sensitivity When Switching (With Regard to The Ambient Brightness)

This setting control can be used to regulate the switch-on sensitivity of this unit depending on the ambient brightness (between 3 and 2.000 LUX).

Sensitivity when switching

Time Setting (Switching Off Delay)

The duration of the operating time can be set continuously from approx. 10s to 15min. The timer is restarted if a movement from the sensor is detected before the set time has elapsed.

$Time setting $switching off delay$$

Function Test

Ensure that the motion detector is not obscured. Ensure that the coverage area is not restricted by items such as through large furniture. To set the detection range and the daylight test, turn the knobs to the positions shown. The motion detector is activated after a warm-up phase of approx. 30s. If no further movement takes place in the sensing area of the sensor, the sensor switches off.

Function test

Technical Data

Operating voltage:|

220 -240V AC 50/60Hz

Maximum power consumption:|

Max. 800W Max. 400W

Consumption in standby:|

< 0,5W

Electrical protection:|

IP44

Protection class:|

II

Detection moving speed:|

0,6-1,5m/s

Ambient temperature:|

-20° – +40°C

Humidity:|

<93%

Possibilities of Adjustments

Detection area:|

Max.12m (<24°C)/180°

Sensitivity when switching (with regard to the ambient brightness):|

<3-2.000LUX

Time setting (switching off delay):|

Min. 10s +/- 3s – Max. 15min +/-2min

Disposal Note: This product may not be disposed of with household waste. At the end of its useful life, the product must be returned to a point of acceptance for the recycling of electric and electronic device. Please ask your local municipality for the point of acceptance! As the devices contain valuable recyclable materials, they should be sent for recycling, in order not to harm the environment or human health from uncontrolled waste disposal.

Cleaning

Danger: Before start cleaning the product interrupt the current circuit by switching off the circuit breaker or unscrew the fuse! Use a slightly moistened cloth for cleaning. In order not to damage the product, it is essential to avoid water penetrating into the housing! Never clean the device under running water! Do not use solvent-containing cleaner for cleaning.