MIBOXER D4-W72 LED Wall Washer Light ( DMX512&RDM) Instruction Manual

Mi-Light
Subordinate New Brand
LED-Wall Washer Light ( DMX512&RDM)
Model No.: D4-W72 / D5-W72

Features

1. Accord with DMX512 standard protocol.
2. Digital Display, Set DMX initial address through the button.
3. Support RDM function.
4. Logarithm/Linear dimming curve is optional.
5. 16 million colors to change, color temperature, and brightness adjustable.
6. IP66 waterproof rated

Parameter

D4-W72
72W RGBW LED Wall Washer Light

Luminous Flux:

D5-W72
72W RGB+CCT LED Wall Washer Light

Luminous Flux:

Function Settings

1. Digital Display status description
   Self-locking: Get into locking state when there is no operation over 30 seconds, digital display with low light or OFF.
   Unlock the Long press M button for 2 seconds to make a digital display with high light, quit self-locking state.
   The address is always ON: DMX signal valid.
   Address flickering: DMX signal invalid.

2. DMX initial address setting
   Under unlock status, when the digital display shows 001-512( for example ) Short press ▲ button or ▼ button, you can change the DMX initial address; Long press, you can change it quickly.
   For Example Set the Initial address to 100

3. System Parameter Setting Instruction
   Under unlock status: Long press the M button 3 seconds to make the digital display show or, then get into the system parameter setting. By this time, short press the M button to switch 3 different parameters setting circularly.
   Parameter 1: Dimming Curve setting (Show  or  ), short press ▲ button or ▼ button to switch.
   The dimming curve is logarithm dimming. (Factory default parameter)
   The dimming curve is linear dimming.
   Parameter 2: Dimming smoothness setting(show or ), short press ▲ button or ▼ button to switch.
   Smooth dimming. (Factory default setting)
   Standard dimming.
   Parameter 3: Digital display showing setting(show or ) short press ▲ button or ▼ button to switch.
   Under self-locking status, the digital display is always ON (low lighting showing). (Factory default parameter)
   Under self-locking status, digital display OFF.
   Exit system mode: long press M button 1 second to exit. Or it will be self exit if there is no operation over 8 seconds.

4. Restore factory default.
   Under unlock status, long-press the M button for 10 seconds until digital display shows .

Dimming Curve Diagram

Installation Diagram

1. Fix the lamp body on the base, and rotate the screws.
   

2. Select the installation place, and fix the base.

3. Adjust the illuminating angle, and tighten the screws.

Connection Diagram

Attention: If the DMX wall washer light is over 32pcs, or using the super long signal cable, you need a DMX signal amplifier. Amplify signal cannot be over 5 times.
Attention

1. This product should be debugged and installed by professionals.
2. Please check whether the input voltage meets the requirements of the product voltage range.
3. Before switching on the power, please ensure that all wiring is correct, so as not to cause damage to the devices.
4. Please do not install the devices in the low-lying and easy inundated areas.
5. If a fault has occurred, non-professionals do not repair it without permission, otherwise, the devices will be damaged.

Made in China

Documents / Resources

| MIBOXER D4-W72 LED Wall Washer Light ( DMX512&RDM) [pdf] Instruction Manual
D4-W72, D5-W72, LED Wall Washer Light DMX512 RDM
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>