MiBOXER Smart LED Strip Control System User Manual
- June 6, 2024
- MiBOXER
Table of Contents
Smart LED Control System
Model No.: FUT043A / FUT044A / FUT045A
Introduction
Smart(set) LED strip control system is our newly developed high-end LED
controller controlled by wireless remote controller, also with smartphone
control and 4G long-distance control(2.4GHz gateway is needed). The controller
has auto-transmitting and auto-synchronizing functions and with RGB, RGBW, and
RGB+CCT output mode.
This controller adopts the widely used 2.4GHz wireless technology with the
features of low power consumption, long signal transmitting, and strong anti-
interference, etc. One compatible remote control has many controllers at the
same time. Widely used on the controlling of hotel lighting and home lighting.
Technical Data
Controller
| Model No.: | FUT043 / FUT044 / FUT045 |
|---|---|
| Working Voltage: | DC12V~24V |
| Output Max: | 6A/Channel |
| Total Output Max: | 15A |
| Working Temperature: | -20~60°C |
| RF: | 2.4GHz |
| Max Controlling Distance: | 30m |
| Output Connection: | Common anode |
| Size: | 372897mm |
Remote control
| Model No.: | FUT088 |
|---|---|
| Working Voltage: | 3V(2*AAA Battery) |
| Transmitting Power: | 6dBm |
| Standby Power: | 20uA |
| Working Temperature: | -20~60°C |
| Radio Frequency: | 2400-2483.5MHz |
| Modulation Method: | GFSK |
| Control Distance: | 30m |
| Size: | 4716.5134mm |
Products Key Diagram
| Touch the color ring to change colors.
---|---
| Under white light mode, adjust color temperature;
Under color light mode, change color saturation.
| Slide the brightness slider to adjust the brightness.
| Touch the ON button, turn on the linked device.
| Touch the OFF button, turn off the linked device.
| Press the button to get white light.
| Static Red Light.
| Static Green Light.
| Static Blue Light.
| Dynamic mode switching button.
| Slow the speed under the present dynamic mode.
Under static mode, Long press for 2 seconds, the light shine once, the light
will be off after 60 seconds.
| Accelerate the speed under present dynamic mode.
Under static mode, Long press for 2 seconds, the light shine once, the light
will be off after 10 minutes.
Auto-synchronization function
Different controllers can work synchronously when they are started at different times, controlled by the same remote, under the same dynamic mode, and with the same speed.
Remark:
- Indicating Auto-transmitting.
- The controller will be auto-synchronizing in the same dynamic modes and within a 30m controlling distance.
Auto-transmitting function
One strip controller can transmit the signals from the remote control to another controller within 30m, as long as there is a strip controller within 30m, the remote control distance can be limitless.
Dynamic Mode Sheet
Number
| Dynamic Mode| Brightness &Speed|
Saturation
---|---|---|---
1| Seven color gradual change| Adjustable| Adjustable
2| White light Gradual change| Unadjustable
3| RGB gradual change| Adjustable
4| Seven colors jump to change
5| Jump to change randomly
6| Red light gradual change+Flash 3times
7| Greenlight gradual change+Flash 3times
8| Blue light gradual change+Flash 3times
9| White light gradual change+Flash 3times| Unadjustable
Linking&Unlinking
Remark: The light can be working after linking with the remote
controller.
Linking Instructions
-
Switch off the light, after 10 seconds switch on again.
-
When the light is on, short press ” ON ” 3 times within 3 seconds.
-
The light blinking 3 times slowly means the linking is done successfully.
If the light does not blink slowly, the linking failed, Pls switch off the
light again, and follow the above steps again.
Unlinking Instructions
-
Switch off the light, after 10 seconds switch on again.
-
When the light is on, short press ” ON ” 5 times within 3 seconds.
-
The light blinking 10 times quickly, means the unblinking successfully.
If the light does not blink quickly, the unlink failed, pls switch off the light again, and follow the above steps to unlink again.
The controller connects to the LED strip diagram
Attention
- Please check whether the input voltage of the constant voltage power supply is in accordance with the controller, and please check the connection of both the cathode and anode, otherwise, the controller will be broken.
- Please don’t connect wires with power on. Please turn it on again only when it is in the right connection and has no short circuit.
- Please do not use the controller in a place with a wide range of metal areas or strong electromagnetic waves nearby, otherwise, the remote distance will be seriously affected.
Made in China
Documents / Resources
|
MiBOXER Smart LED Strip Control
System
[pdf] User Manual
MiBOXER, Smart, LED Control, System, FUT043A, FUT044A, FUT045A
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>