MEMPHIS PRO CART ITC 3 Wood Fire Grill User Guide
- June 6, 2024
- MEMPHIS
Table of Contents
VG0895
Revision:
PRO CART ITC 3 QUICKSTART GUIDE
TOOLS REQUIRED
• 3/8″ Open End Wrench, Socket or Adjustable Wrench
• Phillips Screw Driver or Drill
• Snips or Heavy Duty Scissors
• Cut Resistant Gloves
• 5mm Allen Wrench
| CONTENTS
1: Tools Required
2: Included Hardware 2-
3: Assembly Instructions
4: Wi-Fi Setup and App Pairing
| TIME REQUIRED
1.5 Hours
---|---|---
HARDWARE COMPONENTS
HARDWARE COMPONENTS
| Qty:|
Picture:
---|---|---
1. VG0001Grate Kit|
1
|
2. Savorizer VG4403|
1
|
3. Direct Flame Insert VG4407|
1
|
4. Genie Tool VG1595|
1
|
5. Shelf Bolt DS2311|
10
|
6. Antenna VG9023|
1
|
7. #10 Screw (SS) DS2186|
1
|
8. Cord Wrap VG0560|
1
|
9. Meat Probe VG0956|
1
|
Packaging Locations
MEMPHIS PRO CART ASSEMBLY INSTRUCTIONS
-
Remove both shelves, the hardware kit, Savorizer, and grate kit from the grill. The shelves are located in boxes underneath the grill. The Savorizer and grate kit are in the grill hood. To remove the Savorizer, cut the 4 zip ties holding it in place.
Remove all laser film on the grill. This is a peel-able plastic left on to protect your grill from scratches during manufacturing and transit. Remove all laser film and laser etch lines with WD40 or olive oil. Once a grill has been heated up it is very difficult to remove this film, be sure to check your grill thoroughly before first burn. -
Replace the Savorizer and place 3 large grates on the lower level and the long grate on the upper level.
-
Remove the Direct Flame Insert and Genie Tool from the right side shelf.
-
Install 2 shelf bolt (#5) into the right side of the grill. Leave approximately 1/4” of the bolts sticking out so that the shelf can slide onto them.
NOTE: ALWAYS HOLD SHELVES FROM THE BOTTOM AS THE SHELF TOP SLIDES OPEN! -
Slide the shelf onto the bolts, press down on the shelf to secure into the keyway. Install the remaining 3 shelf bolts. Tighten bolts using 3/8” wrench, socket, or adjustable wrench.
-
Repeat steps 5 and 6 for the left side of the grill.
-
Remove two 5mm socket head screws from Display Housing shipping bracket using the 5mm allen wrench.
-
Snip the zip tie that secures the Display Housing to the shipping bracket.
-
Mount the Display Housing perpendicular to the side panel over the Display Insert bracket using the two 5mm x 40mm socket head screws in the hardware kit.
-
Attach the included antenna to the grill by twisting in a clockwise motion. The antenna will be included in the hardware kit located in the grease tray.
-
Attach the cord wrap with included screws found in the hardware kit.
COMPLETE THE STEPS BELOW IN NUMERICAL ORDER, REFERENCE THE SAME NUMBERED DIAGRAM AND HARDWARE COMPONENTS FOR CLARIFICATION.
MEMPHIS WI-FI SET UP GUIDE
ON YOUR GRILL CONTROLLER:
- Navigate to the Settings Screen on the display.
- Select “Connect to WiFi” to navigate to the Connection Screen.
- Press the blue “Connect WiFi” button to broadcast the BLE signal.
- Follow the steps below on your Memphis 3 App.
ON YOUR PHONE OR TABLET: (In Memphis 3 App)
- Log into Memphis 3 App using your account email and password.
- If no grill is connected, the BLE provisioning process will begin automatically. Otherwise, navigate to the Setting Screen and select “Add Grill”.
- Select your grill from the provisioning screen.
- Select the 2.4GHz network you would like to connect to your Memphis grill, enter the network password, and press “Provision”.
- If successful, the controller will display “Connection Successful” and show the WiFi signal strength in the top right corner.
*Note: If a red X is displayed on the controller instead of the signal strength the connection was unsuccessful. Attempt to provision the controller again, otherwise contact Memphis Technical Support.
GRILL NETWORK INFORMATION
Navigating back to the “Connect to Wifi” Screen displays the Network name, signal strength, and connection status as well the Grill Name, MAC Address and IP Address of your Memphis Grill.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>