SALUS Thermostat and Smart Plug Installation Guide

RT310SPE
Installation Guide

Introduction

The RT310SPE module will switch your appliance on or off in accordance with the temperature set by you. The completed RT310SPE series consists of a transmitter – RT310TX thermostat and a Smart Plug SPE868.
Go to www.salus-manuals.com for the full PDF version of the manual.

Product Compliance

This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com.
868.0-868.6MHz; <13dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.

Button Functions

1. Turn on the LCD backlight.
2. Turn On/Off the Frost Mode.
3. Increase button.
4. Decrease button.
5. Test Mode/ Pairing Mode

LCD icons

1. The thermostat is calling for heat
2. The thermostat is in frost mode
3. The thermostat is sending a signal to the smart plug
4. The low battery indicator icon
5. Temperature display

DIP switch settings

The DIP Switches can be found on the rear of your thermostat.

functional. You can choose the Cycles Per Hour between a
lower comfort level (6CPH) and a higher comfort level (9CPH).| When Span is selected on DIP
switch № 2, the DIP switch № 1 is
not functional. The temperature
accuracy of your thermostat is set
to ± 0.25 °C.

Smart plug LED indication

| Solid Red – paired, a smart plug is off
---|---
| Solid Green – paired, a smart plug is on
| 1. Pulsating red- waiting for pairing
2. Slow Flash red – overheat protection
3. Flashing red – safe mode, lost connection with thermostat and smart plug is off
| Flashing Green – in test pairing mode
| Flashing Red and Green – fail-safe mode, lost connection with thermostat, a smart plug is on

Installation

Step 1

The thermostat and the smart plug are pre-paired from the factory if purchased as a pack. If not, follow the thermostat pairing process.

Step 2 Thermostat pairing process

In case you have more than 1 smart plug, set ALL the smart plugs into pairing mode and start the pairing process. The LED will flash red when the plug is in pairing mode.
Put the thermostat into pairing mode, by pressing the pair button for 3 seconds. After the smart plug is paired with the thermostat, the LED is steady red.
Begin pairing process

End pairing process

Test the pairing process

Change temperature

Note: By changing the Setpoint (desired) temperature, you are permanently altering your temperature.

Frost Mode

If the thermostat loses connection with the Smart Plug, the Smart Plug goes into fail-safe mode after 22 minutes. In this mode, you still can operate your Smart Plug manually (by pressing the button on the device).

Installer mode

Press the three buttons together for 3 seconds. Use to select dxx parameter, ∧ or ∨ to change parameter value and to confirm.

Parameter

0.0°C
d03| Frost setpoint| 5.0-1 7.0°C| Set the Frost Point temperature| 5.0°C

support@salus-controls.de
tel: +49 6108 8258515
Head Office:
SALUS Controls Plc
Units 8-10 Northfield
Business Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
T: +44 (0) 1226 323961
E: sales@salus-tech.com

www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change specification, design, and materials of products listed in this brochure without prior notice.
For PDF Installation guide please go to www.salus-manuals.com
Issue Date: V 2020
V011

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>