SALUS RT310SPE Radio Room Thermostat Installation Guide
- June 6, 2024
- SALUS
Table of Contents
- Introduction
- Product Compliance
- Safety Information
- Button Functions
- LCD icons
- DIP switch settings
- Smart plug LED indication
- Installation – Step 1
- Installation – Step 2
- Thermostat pairing process
- Test the pairing process
- Change temperature
- Frost Mode
- Installer mode
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RT310SPE
Radio Room Thermostat
Installation Guide
Introduction
The RT310SPE module will switch your appliance on or off in accordance with
the temperature set by you. The completed RT310SPE series consists of a
transmitter – RT310TX thermostat and a Smart Plug SPE868.
Go to www.salus-manuals.com for the full PDF
version of the manual.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and
RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on
www.saluslegal.com.
868.0-868.6MHz; <13dBm
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.
Button Functions
- Turn on the LCD backlight.
- Turn On/Off the Frost Mode.
- Increase button.
- Decrease button.
- Test Mode/ Pairing Mode
LCD icons
- Thermostat is calling for heat
- Thermostat is in frost mode
- Thermostat is sending signal to the smart plug
- Low battery indicator icon
- Temperature display
DIP switch settings
The DIP Switches can be found on the rear of your thermostat.
| Control feature | TPI | Span |
|---|---|---|
| Operation | When TPI is selected on DIP switch № 2, the DIP switch № 1 is |
functional. You can choose the Cycles Per Hour between a lower comfort level
(6CPH) and a higher
comfort level (9CPH).| When Span is selected on DIP switch № 2, the DIP switch
№ 1 is not functional. The temperature accuracy of your thermostat is set to
± 0.25 °C.
Smart plug LED indication
| Solid Red – paired, smart plug is off
---|---
| Solid Green – paired, smart plug is on
| 1. Pulsating red- waiting for pairing
2. Slow Flash red – overheat protection
3. Flashing red – safe mode, lost connection with thermostat and smart plug
is off
| Flashing Green – in test pairing mode
| Flashing Red and Green -fail safe mode, lost connection with
thermostat, smart plug is on
Installation – Step 1
The thermostat and the smart plug are pre-paired from the factory if purchased
as a pack. If not, follow thermostat pairing process.
Installation – Step 2
Thermostat pairing process
- In case you have more than 1 smart plug, set ALL the smart plugs into pairing mode and start the pairing process. The LED will flash red when the plug is in pairing mode.
- Put the thermostat into pairing mode, by pressing the pair button for 3 seconds. After the smart plug is paired with the thermostat, the LED is steady red.
Begin pairing process
End pairing process
Test the pairing process
Change temperature
Actual room temperature
Setpoint temperature
Note: By changing the Setpoint (desired) temperature, you are permanently
altering your temperature.
Two seconds timeout
Actual room temperature
Frost Mode
Frostpoint review
Frost Protection Off
If
the thermostat loses connection with the Smart Plug, the Smart Plug goes into
fail safe mode after 22 minutes. In this mode you still can operate your Smart
Plug manually (by pressing the button on the device).
Installer mode
Press the three buttons together for 3 seconds. Use to select dxx parameter, or to change parameter value and to confirm.
Parameter
| dxx | Function | Parameter | Description | Default value |
|---|---|---|---|---|
| d01 | Temperature display increments | 0.1 or 0.5°C | Select temperature display | |
| increments | 0.5°C | |||
| d02 | Temperature offset | +/-3.0°C | Calibrate your thermostat temperature |
0.0°C
d03| Frost setpoint| 5.0-17.0°C| Set the Frost Point temperature| 5.0°C
support@salus-controls.de
tel: +49 6108 8258515
Head Office:
SALUS Controls Plc
Units 8-10 Northfield Business Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
T: +44 (0) 1226 323961
E: sales@salus-tech.com
E: techsupport@salus-tech.com
www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc
reserve the right to change specification, design and materials of products
listed in this brochure
without prior notice.
For PDF Installation guide please go to www.salus-manuals.com
Issue date: 2020 V
Version: V023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>