SALUS SQ610RF Quantum Smart Thermostat Instruction Manual

Introduction

The SQ610RF Quantum is a ZigBee temperature controller for wireless control of iT600 series devices, such as the KL08RF wiring center, mini TRV head, RX10RF boiler control module.
In order to control SQ610RF over the Internet or via the SALUS Smart Home mobile app (ONLINE mode) , it must be installed together with the UGE600 Internet gateway (sold separately). From the application level, it is possible to pair SQ610RF with other system elements, e.g. Smart Plug SPE600, Smart Relay SR600, or window/door sensor OS600/SW600.
SQ610RF can be used locally without an Internet connection (OFFLINE mode) , however, its communication with other devices must be done using the CO10RF coordinator (sold separately).

Full manual in PDF format is available at www. Salus-controls.EU site.

Product Compliance

This product complies with the essential requirements and other relevant provisions of Directives 2014/30/ EU, 2014/35/EU, 2014/53/EU, and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com.

Safety Information

Use in accordance with national and EU regulations. Use the device as intended, keeping it in dry condition. Product for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations. Disconnect your equipment before cleaning it with a dry cloth.

Package Content:

1. SQ610RF Quantum Thermostat
2.  Wall mounting plate
3.  Self-adhesive mounting tape
4.  Mounting screws
5.  Manual instruction

Before you start:

1. New SQ610RF Quantum Thermostat is partially charged, however, we recommend you to fully charge the battery before use. Connect the charger to the micro-USB Port which is at the bottom of the SQ610RF Quantum Thermostat to charge the device.
2. Charging to full battery level may take up to 24h maximum.

Wiring diagram (S1, S2 Input)

3. Mounting: to mount the thermostat you can use included accessories (mounting screws or self-adhesive tape). Remove back cover to mount the plate to the wall. After this just attach the thermostat to the plate (it has a built-in magnet).

Symbols explanation :
S – volt-free contact
T – temperature sensor
S1,S2 Terminals:

•  air or floor temperature sensor
•  external volt-free contact to connect any ON/OFF switch or occupancy sensor (Hotel card)

Please note:

The ideal position to thermostat mounting is about 1,5m under floor level far from heating or cooling sources. The thermostat can’t be exposed to sunlight
or any extreme conditions like for example draft.

LCD Icon Description

1.  Menu/Settings description + Clock
2.  AM/PM
3.  Temperature unit
4.  Heating indicator (icon is animating when there is heating demand)
5.  Cooling indicator (icon is animating when there is cooling demand)
6.  RF Connection indicator
7.  Internet connection indicator
8.  Occupancy sensor (hotel card)
9.  Key lock function
10.  Standby mode icon
11.  Current Temperature / Setpoint Temperature
12.  Holiday mode
13.  Temporary override mode
14.  Settings icon
15.  Battery status indicator
16.  External / Floor temp sensor indicator
17.  Schedule program number
18.  Schedule mode icon
19.  Day indicator/ SET information
20.  Current Humidity value

Buttons Description

1.  Menu button / Return button.
2. In the MAIN SCREEN: Press and hold for 3 sec to change the thermostat operating mode (Schedule mode / Permanent mode / Temporary override mode).
3. In the SETTINGS SCREEN: Press and hold for 3 sec to go back without saving the changes.
4. In the PAIRING SCREEN (in SYSTEM TYPE Menu): Press and hold for 3 sec to see other pairing options.

| „Down” Button (Decrease parameter value/moving on the menu in ‘DOWN’ direction)
| “Up” Button (Increase parameter value/moving on the menu in ‘UP’ direction)
|

1.  Press and hold for 3 seconds to POWER UP new device
2. “OK / Tick” Button (Confirm parameter value / Go to the next menu / Save settings)
3. In the MAIN SCREEN: Press and hold for 3 seconds to enter Standby mode
4. In the SETTINGS SCREEN: Press and hold for 3 sec to go back to the MAIN SCREEN & SAVE all the changes.
5. During the PAIRING process – hold the button for 3 seconds to POWER OFF or REBOOT the thermostat.

| In the MAIN SCREEN – press and hold these buttons together for 3 seconds to LOCK / UNLOCK
the Thermostat keys).

COMPATIBILITY WITH OTHER SALUS CONTROLS DEVICES
Quantum Thermostat can work in ONLINE or OFFLINE mode.
At the first step, you need to decide in which mode your thermostat will work.

Gateway](https://manuals.plus/wp-content/uploads/2021/12/SALUS-SQ610RF- Quantum-Smart-Thermostat-Universal-Gateway-300x153.png)
Download the Smart Home App on your iOS or Android
device for remote access to your SALUS equipment.| Universal Gateway is
CONNECTED TO THE internet you can configure and use all your devices in the Smart Home App
|
Universal Gateway is NOT
CONNECTED TO THE INTERNET
You can use your devices locally without the SmartHome App. Gateway works in this mode as a standard ZigBee coordinator.| CO10RF Coordinator – You can use standard ZigBee network coordinator to install and use your devices.

Compatible devices:

| | | |
---|---|---|---|---
SR600 Smart Relay| SPE600 Smart Plug| KL08RF Wiring Centre for 8-zone underfloor heating (UFH).| TRV (Thermostatic Radiator Valve) with wireless communication.| RX10RF receiver

*Only with Online Mode

First power-up sequence

Please note:

For easier installation, please make sure you have already added other devices to your ZigBee networks, such as Underfloor Heating Control Box (KL08RF) or Radiator heads (TRV’s), etc.

Installation in ONLINE mode

After Language selection follows the below steps to add your device to the Smart Home app and pair it with other devices:

Installation in OFFLINE mode

Pairing with Wiring Centre / Control Box (Install the Wiring Centre / Control Box according to the instructions included with product)

Pairing with TRV radiator head (Install the TRV according to the instructions included with product)

SQ610RF Full menu structure

Main menu

SQ610RF Full menu structure

Schedule settings

| DISABLE MO-FR+SA-SU MO-SU SINGLE DAYS

User settings

| TIME/DATE HOLIDAY MODE THERMOSTAT CALIBRATION SHOW/HIDE DISPLAY HUMIDITY SHOW/HIDE DISPLAY FLOOR STANDBY TEMP SETPOINT HEAT/COOL RESET USER SETTINGS

Admin settings

| TEMPERATURE SCALE DISPLAY TEMPERATURE RESOLUTION 1. HEAT CONTROL ALGORITHM 2. COOL CONTROL ALGORITHM S1/S2 INPUT 3. MINIMUM SETPOINT MAXIMUM SETPOINT VALVE PROTECTION 4. MINIMUM TURN-OFF TIME 5. OPTIMISATION FEATURE 6. COMFORT WARM FLOOR 7. PIN CODE DEVICE INFORMATION 8. FACTORY RESET 9.

Language

| ENGLISH DANISH POLISH

Short description of some selected functions
(all functions are described in the full version of the SQ610RF manual):

1. DISPLAY TEMP RESOLUTION: This function determines the resolution of the displayed temperature – User can temperature set by steps (every 0,5°C or 0,1°C).
2. CONTROL ALGORITHM: This function defines how to control the room temperature. Available options are ITLC for Underfloor Heating / Radiators / Electrical Heating (that’s an advanced algorithm for precise maintenance of room temperature), hysteresis +/-0.5°C or +/-0.25°C, THB Actuator (option recommended for systems with THB auto-balancing actuators).
3. S1/S2 INPUT: A floor sensor, an external temperature sensor, or an occupancy sensor can be connected to the S1/S2 input of SQ610RF. Additionally, by connecting a NO type of ON/OFF voltage-free contact, you can use this input as a OneTouch rules trigger (programmed in the Salus Smart Home app) or as a Heat/ Cool changeover.
4. VALVE PROTECTION: This function activates all actuators once a week for 5 minutes (in summer, this function helps to prevent the actuators stuck).
5. MIN TURN OFF TIME: Minimum switch-off time (thermostat will not send the signal for heating/ cooling more often than specified in this parameter).
6. OPTIMISATION FEATURE: Optimum Start and Optimum Stop functions are energy-saving features that make the thermostat most cost-effective (in combination with the ITLC control algorithm).
7. COMFORT WARM FLOOR: This function helps to keep the floor warm, even if the room is warm enough and there is no need to turn on the heating. Users can select 3 levels of the warm floor features. Please note it is not an economy feature, as your heating system may be ON even if there is no heating demand from the room thermostat. It is a COMFORT feature which keeps your floor warm all the time.
8. DEVICE INFORMATION: In this menu, the user can check: Software Version, Battery Level, RF range value; Paired devices or also user can activate Identification mode.
9. FACTORY RESET: Here you can RESET your device to factory settings. After successful reset device will be removed from the ZigBee network and you will need to add/pair your device again.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>