Wahl 8483 Rotary Corded Clipper User Manual

: June 6, 2024
: WAHL

Wahl 8483 Rotary Corded Clipper

Includes But Not Limited To:
All Wahl, 5 Star & Sterling Vibratory Clippersand Rotary Clippers Pilot & Nugg

IMPORTANT SAFEGUARDS

When using your electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS AND SAFEGUARDS BEFORE USING THIS APPLIANCE.

DANGER

To reduce the risk of death or injury by electric shock:

Do not reach for an appliance that has fallen into water. Unplug immediately from the outlet. Note: Some electrical parts inside the appliance are electrically live, even with the switch “OFF.”
Do not use while bathing or in a shower.
Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
Always unplug this appliance before cleaning.
Always unplug this appliance from the electrical outlet immediately after using.

WARNING

To reduce the risk of burns, electrical shock or injury to persons:

This appliance can be used by children aged from 14 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction, by a person responsible for their safety, concerning the use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Use this appliance only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.
Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has been dropped into water. Return the appliance to Wahl Clipper Corporation for examination and repair.
Keep the cord away from heated surfaces.
Never operate the appliance with the air openings blocked or while on a soft combustible surface, such as a bed or couch, where air openings may be blocked. Keep the air openings (if any) free from lint, hair or the like.
Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
Never drop or insert any object into any opening.
Do not use this appliance with a damaged or broken comb nor with teeth missing from the blades, as injury may occur. Before use, make certain blades are aligned properly. (See Clipper or Trimmer Care Instructions. May not be applicable for all appliances.)
During use, do not place or leave the appliance where it is expected to be subject to damage by an animal, or exposed to weather.
To disconnect, turn all controls to “OFF,” then remove plug from outlet.
Turn all controls to “OFF” before placing on or removing blades or attachments.
An appliance with a permanently attached cord should never be left unattended when plugged in.
Keep this appliance dry.
If your appliance is grounded (see Fig. 1 for grounded plug), connect it to a properly grounded outlet only. (See Grounding Instructions.)

SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR COMMERCIAL USE ONLY

GROUNDING INSTRUCTIONS

(Grounding Instructions only apply if the appliance has a grounding pin as shown in Figure 1.)This appliance should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all
local codes and ordinances.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat-blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the appliance is properly grounded. Do not modify the plug provided; if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

VIBRATORY CLIPPER DIAGRAM

CLIPPER USE

USING CORDED CLIPPERS

TAPER LEVER
Some clippers are equipped with an adjustable taper lever that changes the closeness of your cut. When the lever is in the uppermost position, the blades will give the closest cut. Pushing the lever downward gradually increases the cutting length. (Not found on all clipper models.)

POWER ADJUSTMENT SCREW

MAXIMIZING POWER TO THE BLADES

To adjust power, turn power screw in clockwise direction until clipper makes a noise caused by the arm hitting the coil. Then, slowly turn power screw out (counter-clockwise) just until noise stops then continue turning 1/8 to 1/4 of a turn more, this is maximum power. (Not found on all clipper models.)

POWER ADJUSTMENT SCREW DIAGRAM

QUICK TIP

Use the brush handle tip to adjust the power screw.

CLIPPER CARE

BLADE CARE AND OILING

In order to ensure that you get the most life and performance out of the clipper, we recommend oiling daily. To oil it properly, the clipper should be held so the blades are in a downward position as shown.
Place one drop of Wahl oil in the center of the movable top blade and one drop of oil on each end of the top blade. Turn clipper switch ON and run to distribute the oil. When oil is evenly distributed, turn clipper OFF and wipe off excess oil with a soft cloth. Periodically oil heel of blade (shown in image) to reduce blade friction.

(USE WAHL OIL ONLY)

WIPE OFF EXCESS OIL so it does not run into the motor compartment.
Oil in the motor compartment will eventually lead to poor motor performance.
Blades should be oiled after using disinfectant or sanitizing solution.

UNIT CARE

Use a clean cloth (dry or dampened with water).
DO NOT USE bleach, benzene or thinner to clean the unit.

CORD CARE

The cord should never be used to pull the clipper.Freedom of movement needs to be maintained. Care should be used to keep the cord untwisted, and undamaged. When stored, the cord should be coiled and placed neatly in a dry place.

BLADE ALIGNMENT DIAGRAM

ALIGNING 2 HOLE BLADES

Slightly loosen both blade screws at base of stationary blade, just enough to be able to shift the blade. Move blade adjustment lever to the full forward position. With the blade screws loosened, the bottom blade can be aligned with the top blade.

Points of the top blade teeth should be 1/32” to 1/16” (.79mm to 1.59mm) back and parallel to the points of bottom blade teeth. This is important so the clipper doesn’t cut too close or allow the moving top blade to touch the skin. (See Blade Alignment Diagram.)
Extreme left hand tooth of top blade must be on the first small tooth of bottom blade. (See Blade Alignment Diagram.)
After blade is aligned, tighten screws.
Plug clipper in, turn switch ON and OFF a couple of times, and then recheck alignment of blades.

ALIGNING 3 HOLE BLADES

Slightly loosen the three blade screws of the stationary blade, just enough to be able to shift the blade. Move blade adjustment lever to the full forward position. With the blade screws loosened, the bottom blade can be aligned with the top blade.
Aligning-3-Hole-Blades

Points of the top blade teeth should be 1/32” to 1/16” (.79mm to 1.59mm)back and parallel to the points of bottom blade teeth. This is important so the clipper doesn’t cut too close or allow the moving top blade to touch the skin. (See Blade Alignment Diagram.)
Extreme left hand tooth of top blade must be on the first small tooth of bottom blade. (See Blade Alignment Diagram.)
After blade is aligned, tighten screws.
Plug clipper in, turn switch ON and OFF a couple of times, and then recheck alignment of blades.

TROUBLESHOOTING

If your corded clipper does not seem to be operating properly, please
check the following:

Check the outlet’s current by plugging another appliance (one you know is in proper working condition) into the outlet.
Make sure the unit is not connected to a power source that turns itself off when lights are turned off.
Make sure the unit is clean and free of hair or other contaminants.
Verify that the blade assembly moves freely and is mounted properly.

If you still encounter problems with your unit, send your unit to Wahl Clipper Corporation with a note explaining the problem.

Wahl Clipper Corporation offers a limited warranty on this product.
Please visit our website for full warranty terms.